Warning: This file is not a C or C++ file. It does not have highlighting.

1/* SPDX-License-Identifier: GPL-2.0-only */
2/*
3 * Definitions for Compaq iPAQ H3100 and H3600 handheld computers
4 *
5 * (c) 2000 Compaq Computer Corporation. (Author: Jamey Hicks)
6 * (c) 2009 Dmitry Artamonow <mad_soft@inbox.ru>
7 */
8
9#ifndef _INCLUDE_H3XXX_H_
10#define _INCLUDE_H3XXX_H_
11
12#include "hardware.h" /* Gives GPIO_MAX */
13
14/* Physical memory regions corresponding to chip selects */
15#define H3600_EGPIO_PHYS (SA1100_CS5_PHYS + 0x01000000)
16#define H3600_BANK_2_PHYS SA1100_CS2_PHYS
17#define H3600_BANK_4_PHYS SA1100_CS4_PHYS
18
19/* Virtual memory regions corresponding to chip selects 2 & 4 (used on sleeves) */
20#define H3600_EGPIO_VIRT 0xf0000000
21#define H3600_BANK_2_VIRT 0xf1000000
22#define H3600_BANK_4_VIRT 0xf3800000
23
24/*
25 * gpiolib numbers for all iPAQs
26 */
27#define H3XXX_GPIO_PWR_BUTTON 0
28#define H3XXX_GPIO_PCMCIA_CD1 10
29#define H3XXX_GPIO_PCMCIA_IRQ1 11
30#define H3XXX_GPIO_PCMCIA_CD0 17
31#define H3XXX_GPIO_ACTION_BUTTON 18
32#define H3XXX_GPIO_SYS_CLK 19
33#define H3XXX_GPIO_PCMCIA_IRQ0 21
34#define H3XXX_GPIO_COM_DCD 23
35#define H3XXX_GPIO_OPTION 24
36#define H3XXX_GPIO_COM_CTS 25
37#define H3XXX_GPIO_COM_RTS 26
38
39/* machine-specific gpios */
40
41#define H3100_GPIO_BT_ON 2
42#define H3100_GPIO_QMUTE 4
43#define H3100_GPIO_LCD_3V_ON 5
44#define H3100_GPIO_AUD_ON 6
45#define H3100_GPIO_AUD_PWR_ON 7
46#define H3100_GPIO_IR_ON 8
47#define H3100_GPIO_IR_FSEL 9
48
49#define H3600_GPIO_CLK_SET0 12 /* audio sample rate clock generator */
50#define H3600_GPIO_CLK_SET1 13
51#define H3600_GPIO_SOFT_RESET 20 /* also known as BATT_FAULT */
52#define H3600_GPIO_OPT_LOCK 22
53#define H3600_GPIO_OPT_DET 27
54
55
56/* H3100 / 3600 EGPIO pins */
57#define H3XXX_EGPIO_BASE (GPIO_MAX + 1)
58
59#define H3XXX_EGPIO_VPP_ON (H3XXX_EGPIO_BASE + 0)
60#define H3XXX_EGPIO_CARD_RESET (H3XXX_EGPIO_BASE + 1) /* reset the attached pcmcia/compactflash card. active high. */
61#define H3XXX_EGPIO_OPT_RESET (H3XXX_EGPIO_BASE + 2) /* reset the attached option pack. active high. */
62#define H3XXX_EGPIO_CODEC_NRESET (H3XXX_EGPIO_BASE + 3) /* reset the onboard UDA1341. active low. */
63#define H3XXX_EGPIO_OPT_NVRAM_ON (H3XXX_EGPIO_BASE + 4) /* apply power to optionpack nvram, active high. */
64#define H3XXX_EGPIO_OPT_ON (H3XXX_EGPIO_BASE + 5) /* full power to option pack. active high. */
65#define H3XXX_EGPIO_LCD_ON (H3XXX_EGPIO_BASE + 6) /* enable 3.3V to LCD. active high. */
66#define H3XXX_EGPIO_RS232_ON (H3XXX_EGPIO_BASE + 7) /* UART3 transceiver force on. Active high. */
67
68/* H3600 only EGPIO pins */
69#define H3600_EGPIO_LCD_PCI (H3XXX_EGPIO_BASE + 8) /* LCD control IC enable. active high. */
70#define H3600_EGPIO_IR_ON (H3XXX_EGPIO_BASE + 9) /* apply power to IR module. active high. */
71#define H3600_EGPIO_AUD_AMP_ON (H3XXX_EGPIO_BASE + 10) /* apply power to audio power amp. active high. */
72#define H3600_EGPIO_AUD_PWR_ON (H3XXX_EGPIO_BASE + 11) /* apply power to reset of audio circuit. active high. */
73#define H3600_EGPIO_QMUTE (H3XXX_EGPIO_BASE + 12) /* mute control for onboard UDA1341. active high. */
74#define H3600_EGPIO_IR_FSEL (H3XXX_EGPIO_BASE + 13) /* IR speed select: 1->fast, 0->slow */
75#define H3600_EGPIO_LCD_5V_ON (H3XXX_EGPIO_BASE + 14) /* enable 5V to LCD. active high. */
76#define H3600_EGPIO_LVDD_ON (H3XXX_EGPIO_BASE + 15) /* enable 9V and -6.5V to LCD. */
77
78void __init h3xxx_map_io(void);
79void __init h3xxx_mach_init(void);
80
81#endif /* _INCLUDE_H3XXX_H_ */
82

Warning: This file is not a C or C++ file. It does not have highlighting.

source code of linux/arch/arm/mach-sa1100/include/mach/h3xxx.h