1/*
2 * Copyright 2005 Nicolai Haehnle et al.
3 * Copyright 2008 Advanced Micro Devices, Inc.
4 * Copyright 2009 Jerome Glisse.
5 *
6 * Permission is hereby granted, free of charge, to any person obtaining a
7 * copy of this software and associated documentation files (the "Software"),
8 * to deal in the Software without restriction, including without limitation
9 * the rights to use, copy, modify, merge, publish, distribute, sublicense,
10 * and/or sell copies of the Software, and to permit persons to whom the
11 * Software is furnished to do so, subject to the following conditions:
12 *
13 * The above copyright notice and this permission notice shall be included in
14 * all copies or substantial portions of the Software.
15 *
16 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
17 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
18 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
19 * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
20 * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
21 * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
22 * OTHER DEALINGS IN THE SOFTWARE.
23 *
24 * Authors: Nicolai Haehnle
25 * Jerome Glisse
26 */
27#ifndef _R300_REG_H_
28#define _R300_REG_H_
29
30#define R300_SURF_TILE_MACRO (1<<16)
31#define R300_SURF_TILE_MICRO (2<<16)
32#define R300_SURF_TILE_BOTH (3<<16)
33
34
35#define R300_MC_INIT_MISC_LAT_TIMER 0x180
36# define R300_MC_MISC__MC_CPR_INIT_LAT_SHIFT 0
37# define R300_MC_MISC__MC_VF_INIT_LAT_SHIFT 4
38# define R300_MC_MISC__MC_DISP0R_INIT_LAT_SHIFT 8
39# define R300_MC_MISC__MC_DISP1R_INIT_LAT_SHIFT 12
40# define R300_MC_MISC__MC_FIXED_INIT_LAT_SHIFT 16
41# define R300_MC_MISC__MC_E2R_INIT_LAT_SHIFT 20
42# define R300_MC_MISC__MC_SAME_PAGE_PRIO_SHIFT 24
43# define R300_MC_MISC__MC_GLOBW_INIT_LAT_SHIFT 28
44
45#define R300_MC_INIT_GFX_LAT_TIMER 0x154
46# define R300_MC_MISC__MC_G3D0R_INIT_LAT_SHIFT 0
47# define R300_MC_MISC__MC_G3D1R_INIT_LAT_SHIFT 4
48# define R300_MC_MISC__MC_G3D2R_INIT_LAT_SHIFT 8
49# define R300_MC_MISC__MC_G3D3R_INIT_LAT_SHIFT 12
50# define R300_MC_MISC__MC_TX0R_INIT_LAT_SHIFT 16
51# define R300_MC_MISC__MC_TX1R_INIT_LAT_SHIFT 20
52# define R300_MC_MISC__MC_GLOBR_INIT_LAT_SHIFT 24
53# define R300_MC_MISC__MC_GLOBW_FULL_LAT_SHIFT 28
54
55/*
56 * This file contains registers and constants for the R300. They have been
57 * found mostly by examining command buffers captured using glxtest, as well
58 * as by extrapolating some known registers and constants from the R200.
59 * I am fairly certain that they are correct unless stated otherwise
60 * in comments.
61 */
62
63#define R300_SE_VPORT_XSCALE 0x1D98
64#define R300_SE_VPORT_XOFFSET 0x1D9C
65#define R300_SE_VPORT_YSCALE 0x1DA0
66#define R300_SE_VPORT_YOFFSET 0x1DA4
67#define R300_SE_VPORT_ZSCALE 0x1DA8
68#define R300_SE_VPORT_ZOFFSET 0x1DAC
69
70
71/*
72 * Vertex Array Processing (VAP) Control
73 * Stolen from r200 code from Christoph Brill (It's a guess!)
74 */
75#define R300_VAP_CNTL 0x2080
76
77/* This register is written directly and also starts data section
78 * in many 3d CP_PACKET3's
79 */
80#define R300_VAP_VF_CNTL 0x2084
81# define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0
82# define R300_VAP_VF_CNTL__PRIM_NONE (0<<0)
83# define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0)
84# define R300_VAP_VF_CNTL__PRIM_LINES (2<<0)
85# define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0)
86# define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0)
87# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0)
88# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0)
89# define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0)
90# define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0)
91# define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0)
92# define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0)
93
94# define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4
95 /* State based - direct writes to registers trigger vertex
96 generation */
97# define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4)
98# define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4)
99# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4)
100# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4)
101
102 /* I don't think I saw these three used.. */
103# define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6
104# define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9
105# define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10
106
107 /* index size - when not set the indices are assumed to be 16 bit */
108# define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11)
109 /* number of vertices */
110# define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16
111
112/* BEGIN: Wild guesses */
113#define R300_VAP_OUTPUT_VTX_FMT_0 0x2090
114# define R300_VAP_OUTPUT_VTX_FMT_0__POS_PRESENT (1<<0)
115# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_PRESENT (1<<1)
116# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */
117# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */
118# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */
119# define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */
120
121#define R300_VAP_OUTPUT_VTX_FMT_1 0x2094
122 /* each of the following is 3 bits wide, specifies number
123 of components */
124# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0
125# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3
126# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6
127# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_3_COMP_CNT_SHIFT 9
128# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_4_COMP_CNT_SHIFT 12
129# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15
130# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18
131# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21
132/* END: Wild guesses */
133
134#define R300_SE_VTE_CNTL 0x20b0
135# define R300_VPORT_X_SCALE_ENA 0x00000001
136# define R300_VPORT_X_OFFSET_ENA 0x00000002
137# define R300_VPORT_Y_SCALE_ENA 0x00000004
138# define R300_VPORT_Y_OFFSET_ENA 0x00000008
139# define R300_VPORT_Z_SCALE_ENA 0x00000010
140# define R300_VPORT_Z_OFFSET_ENA 0x00000020
141# define R300_VTX_XY_FMT 0x00000100
142# define R300_VTX_Z_FMT 0x00000200
143# define R300_VTX_W0_FMT 0x00000400
144# define R300_VTX_W0_NORMALIZE 0x00000800
145# define R300_VTX_ST_DENORMALIZED 0x00001000
146
147/* BEGIN: Vertex data assembly - lots of uncertainties */
148
149/* gap */
150
151#define R300_VAP_CNTL_STATUS 0x2140
152# define R300_VC_NO_SWAP (0 << 0)
153# define R300_VC_16BIT_SWAP (1 << 0)
154# define R300_VC_32BIT_SWAP (2 << 0)
155# define R300_VAP_TCL_BYPASS (1 << 8)
156
157/* gap */
158
159/* Where do we get our vertex data?
160 *
161 * Vertex data either comes either from immediate mode registers or from
162 * vertex arrays.
163 * There appears to be no mixed mode (though we can force the pitch of
164 * vertex arrays to 0, effectively reusing the same element over and over
165 * again).
166 *
167 * Immediate mode is controlled by the INPUT_CNTL registers. I am not sure
168 * if these registers influence vertex array processing.
169 *
170 * Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3.
171 *
172 * In both cases, vertex attributes are then passed through INPUT_ROUTE.
173 *
174 * Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data
175 * into the vertex processor's input registers.
176 * The first word routes the first input, the second word the second, etc.
177 * The corresponding input is routed into the register with the given index.
178 * The list is ended by a word with INPUT_ROUTE_END set.
179 *
180 * Always set COMPONENTS_4 in immediate mode.
181 */
182
183#define R300_VAP_INPUT_ROUTE_0_0 0x2150
184# define R300_INPUT_ROUTE_COMPONENTS_1 (0 << 0)
185# define R300_INPUT_ROUTE_COMPONENTS_2 (1 << 0)
186# define R300_INPUT_ROUTE_COMPONENTS_3 (2 << 0)
187# define R300_INPUT_ROUTE_COMPONENTS_4 (3 << 0)
188# define R300_INPUT_ROUTE_COMPONENTS_RGBA (4 << 0) /* GUESS */
189# define R300_VAP_INPUT_ROUTE_IDX_SHIFT 8
190# define R300_VAP_INPUT_ROUTE_IDX_MASK (31 << 8) /* GUESS */
191# define R300_VAP_INPUT_ROUTE_END (1 << 13)
192# define R300_INPUT_ROUTE_IMMEDIATE_MODE (0 << 14) /* GUESS */
193# define R300_INPUT_ROUTE_FLOAT (1 << 14) /* GUESS */
194# define R300_INPUT_ROUTE_UNSIGNED_BYTE (2 << 14) /* GUESS */
195# define R300_INPUT_ROUTE_FLOAT_COLOR (3 << 14) /* GUESS */
196#define R300_VAP_INPUT_ROUTE_0_1 0x2154
197#define R300_VAP_INPUT_ROUTE_0_2 0x2158
198#define R300_VAP_INPUT_ROUTE_0_3 0x215C
199#define R300_VAP_INPUT_ROUTE_0_4 0x2160
200#define R300_VAP_INPUT_ROUTE_0_5 0x2164
201#define R300_VAP_INPUT_ROUTE_0_6 0x2168
202#define R300_VAP_INPUT_ROUTE_0_7 0x216C
203
204/* gap */
205
206/* Notes:
207 * - always set up to produce at least two attributes:
208 * if vertex program uses only position, fglrx will set normal, too
209 * - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal.
210 */
211#define R300_VAP_INPUT_CNTL_0 0x2180
212# define R300_INPUT_CNTL_0_COLOR 0x00000001
213#define R300_VAP_INPUT_CNTL_1 0x2184
214# define R300_INPUT_CNTL_POS 0x00000001
215# define R300_INPUT_CNTL_NORMAL 0x00000002
216# define R300_INPUT_CNTL_COLOR 0x00000004
217# define R300_INPUT_CNTL_TC0 0x00000400
218# define R300_INPUT_CNTL_TC1 0x00000800
219# define R300_INPUT_CNTL_TC2 0x00001000 /* GUESS */
220# define R300_INPUT_CNTL_TC3 0x00002000 /* GUESS */
221# define R300_INPUT_CNTL_TC4 0x00004000 /* GUESS */
222# define R300_INPUT_CNTL_TC5 0x00008000 /* GUESS */
223# define R300_INPUT_CNTL_TC6 0x00010000 /* GUESS */
224# define R300_INPUT_CNTL_TC7 0x00020000 /* GUESS */
225
226/* gap */
227
228/* Words parallel to INPUT_ROUTE_0; All words that are active in INPUT_ROUTE_0
229 * are set to a swizzling bit pattern, other words are 0.
230 *
231 * In immediate mode, the pattern is always set to xyzw. In vertex array
232 * mode, the swizzling pattern is e.g. used to set zw components in texture
233 * coordinates with only tweo components.
234 */
235#define R300_VAP_INPUT_ROUTE_1_0 0x21E0
236# define R300_INPUT_ROUTE_SELECT_X 0
237# define R300_INPUT_ROUTE_SELECT_Y 1
238# define R300_INPUT_ROUTE_SELECT_Z 2
239# define R300_INPUT_ROUTE_SELECT_W 3
240# define R300_INPUT_ROUTE_SELECT_ZERO 4
241# define R300_INPUT_ROUTE_SELECT_ONE 5
242# define R300_INPUT_ROUTE_SELECT_MASK 7
243# define R300_INPUT_ROUTE_X_SHIFT 0
244# define R300_INPUT_ROUTE_Y_SHIFT 3
245# define R300_INPUT_ROUTE_Z_SHIFT 6
246# define R300_INPUT_ROUTE_W_SHIFT 9
247# define R300_INPUT_ROUTE_ENABLE (15 << 12)
248#define R300_VAP_INPUT_ROUTE_1_1 0x21E4
249#define R300_VAP_INPUT_ROUTE_1_2 0x21E8
250#define R300_VAP_INPUT_ROUTE_1_3 0x21EC
251#define R300_VAP_INPUT_ROUTE_1_4 0x21F0
252#define R300_VAP_INPUT_ROUTE_1_5 0x21F4
253#define R300_VAP_INPUT_ROUTE_1_6 0x21F8
254#define R300_VAP_INPUT_ROUTE_1_7 0x21FC
255
256/* END: Vertex data assembly */
257
258/* gap */
259
260/* BEGIN: Upload vertex program and data */
261
262/*
263 * The programmable vertex shader unit has a memory bank of unknown size
264 * that can be written to in 16 byte units by writing the address into
265 * UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs).
266 *
267 * Pointers into the memory bank are always in multiples of 16 bytes.
268 *
269 * The memory bank is divided into areas with fixed meaning.
270 *
271 * Starting at address UPLOAD_PROGRAM: Vertex program instructions.
272 * Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB),
273 * whereas the difference between known addresses suggests size 512.
274 *
275 * Starting at address UPLOAD_PARAMETERS: Vertex program parameters.
276 * Native reported limits and the VPI layout suggest size 256, whereas
277 * difference between known addresses suggests size 512.
278 *
279 * At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the
280 * floating point pointsize. The exact purpose of this state is uncertain,
281 * as there is also the R300_RE_POINTSIZE register.
282 *
283 * Multiple vertex programs and parameter sets can be loaded at once,
284 * which could explain the size discrepancy.
285 */
286#define R300_VAP_PVS_UPLOAD_ADDRESS 0x2200
287# define R300_PVS_UPLOAD_PROGRAM 0x00000000
288# define R300_PVS_UPLOAD_PARAMETERS 0x00000200
289# define R300_PVS_UPLOAD_POINTSIZE 0x00000406
290
291/* gap */
292
293#define R300_VAP_PVS_UPLOAD_DATA 0x2208
294
295/* END: Upload vertex program and data */
296
297/* gap */
298
299/* I do not know the purpose of this register. However, I do know that
300 * it is set to 221C_CLEAR for clear operations and to 221C_NORMAL
301 * for normal rendering.
302 */
303#define R300_VAP_UNKNOWN_221C 0x221C
304# define R300_221C_NORMAL 0x00000000
305# define R300_221C_CLEAR 0x0001C000
306
307/* These seem to be per-pixel and per-vertex X and Y clipping planes. The first
308 * plane is per-pixel and the second plane is per-vertex.
309 *
310 * This was determined by experimentation alone but I believe it is correct.
311 *
312 * These registers are called X_QUAD0_1_FL to X_QUAD0_4_FL by glxtest.
313 */
314#define R300_VAP_CLIP_X_0 0x2220
315#define R300_VAP_CLIP_X_1 0x2224
316#define R300_VAP_CLIP_Y_0 0x2228
317#define R300_VAP_CLIP_Y_1 0x2230
318
319/* gap */
320
321/* Sometimes, END_OF_PKT and 0x2284=0 are the only commands sent between
322 * rendering commands and overwriting vertex program parameters.
323 * Therefore, I suspect writing zero to 0x2284 synchronizes the engine and
324 * avoids bugs caused by still running shaders reading bad data from memory.
325 */
326#define R300_VAP_PVS_STATE_FLUSH_REG 0x2284
327
328/* Absolutely no clue what this register is about. */
329#define R300_VAP_UNKNOWN_2288 0x2288
330# define R300_2288_R300 0x00750000 /* -- nh */
331# define R300_2288_RV350 0x0000FFFF /* -- Vladimir */
332
333/* gap */
334
335/* Addresses are relative to the vertex program instruction area of the
336 * memory bank. PROGRAM_END points to the last instruction of the active
337 * program
338 *
339 * The meaning of the two UNKNOWN fields is obviously not known. However,
340 * experiments so far have shown that both *must* point to an instruction
341 * inside the vertex program, otherwise the GPU locks up.
342 *
343 * fglrx usually sets CNTL_3_UNKNOWN to the end of the program and
344 * R300_PVS_CNTL_1_POS_END_SHIFT points to instruction where last write to
345 * position takes place.
346 *
347 * Most likely this is used to ignore rest of the program in cases
348 * where group of verts arent visible. For some reason this "section"
349 * is sometimes accepted other instruction that have no relationship with
350 * position calculations.
351 */
352#define R300_VAP_PVS_CNTL_1 0x22D0
353# define R300_PVS_CNTL_1_PROGRAM_START_SHIFT 0
354# define R300_PVS_CNTL_1_POS_END_SHIFT 10
355# define R300_PVS_CNTL_1_PROGRAM_END_SHIFT 20
356/* Addresses are relative the vertex program parameters area. */
357#define R300_VAP_PVS_CNTL_2 0x22D4
358# define R300_PVS_CNTL_2_PARAM_OFFSET_SHIFT 0
359# define R300_PVS_CNTL_2_PARAM_COUNT_SHIFT 16
360#define R300_VAP_PVS_CNTL_3 0x22D8
361# define R300_PVS_CNTL_3_PROGRAM_UNKNOWN_SHIFT 10
362# define R300_PVS_CNTL_3_PROGRAM_UNKNOWN2_SHIFT 0
363
364/* The entire range from 0x2300 to 0x2AC inclusive seems to be used for
365 * immediate vertices
366 */
367#define R300_VAP_VTX_COLOR_R 0x2464
368#define R300_VAP_VTX_COLOR_G 0x2468
369#define R300_VAP_VTX_COLOR_B 0x246C
370#define R300_VAP_VTX_POS_0_X_1 0x2490 /* used for glVertex2*() */
371#define R300_VAP_VTX_POS_0_Y_1 0x2494
372#define R300_VAP_VTX_COLOR_PKD 0x249C /* RGBA */
373#define R300_VAP_VTX_POS_0_X_2 0x24A0 /* used for glVertex3*() */
374#define R300_VAP_VTX_POS_0_Y_2 0x24A4
375#define R300_VAP_VTX_POS_0_Z_2 0x24A8
376/* write 0 to indicate end of packet? */
377#define R300_VAP_VTX_END_OF_PKT 0x24AC
378
379/* gap */
380
381/* These are values from r300_reg/r300_reg.h - they are known to be correct
382 * and are here so we can use one register file instead of several
383 * - Vladimir
384 */
385#define R300_GB_VAP_RASTER_VTX_FMT_0 0x4000
386# define R300_GB_VAP_RASTER_VTX_FMT_0__POS_PRESENT (1<<0)
387# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_0_PRESENT (1<<1)
388# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_1_PRESENT (1<<2)
389# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_2_PRESENT (1<<3)
390# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_3_PRESENT (1<<4)
391# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_SPACE (0xf<<5)
392# define R300_GB_VAP_RASTER_VTX_FMT_0__PT_SIZE_PRESENT (0x1<<16)
393
394#define R300_GB_VAP_RASTER_VTX_FMT_1 0x4004
395 /* each of the following is 3 bits wide, specifies number
396 of components */
397# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0
398# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3
399# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6
400# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_3_COMP_CNT_SHIFT 9
401# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_4_COMP_CNT_SHIFT 12
402# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15
403# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18
404# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21
405
406/* UNK30 seems to enables point to quad transformation on textures
407 * (or something closely related to that).
408 * This bit is rather fatal at the time being due to lackings at pixel
409 * shader side
410 */
411#define R300_GB_ENABLE 0x4008
412# define R300_GB_POINT_STUFF_ENABLE (1<<0)
413# define R300_GB_LINE_STUFF_ENABLE (1<<1)
414# define R300_GB_TRIANGLE_STUFF_ENABLE (1<<2)
415# define R300_GB_STENCIL_AUTO_ENABLE (1<<4)
416# define R300_GB_UNK31 (1<<31)
417 /* each of the following is 2 bits wide */
418#define R300_GB_TEX_REPLICATE 0
419#define R300_GB_TEX_ST 1
420#define R300_GB_TEX_STR 2
421# define R300_GB_TEX0_SOURCE_SHIFT 16
422# define R300_GB_TEX1_SOURCE_SHIFT 18
423# define R300_GB_TEX2_SOURCE_SHIFT 20
424# define R300_GB_TEX3_SOURCE_SHIFT 22
425# define R300_GB_TEX4_SOURCE_SHIFT 24
426# define R300_GB_TEX5_SOURCE_SHIFT 26
427# define R300_GB_TEX6_SOURCE_SHIFT 28
428# define R300_GB_TEX7_SOURCE_SHIFT 30
429
430/* MSPOS - positions for multisample antialiasing (?) */
431#define R300_GB_MSPOS0 0x4010
432 /* shifts - each of the fields is 4 bits */
433# define R300_GB_MSPOS0__MS_X0_SHIFT 0
434# define R300_GB_MSPOS0__MS_Y0_SHIFT 4
435# define R300_GB_MSPOS0__MS_X1_SHIFT 8
436# define R300_GB_MSPOS0__MS_Y1_SHIFT 12
437# define R300_GB_MSPOS0__MS_X2_SHIFT 16
438# define R300_GB_MSPOS0__MS_Y2_SHIFT 20
439# define R300_GB_MSPOS0__MSBD0_Y 24
440# define R300_GB_MSPOS0__MSBD0_X 28
441
442#define R300_GB_MSPOS1 0x4014
443# define R300_GB_MSPOS1__MS_X3_SHIFT 0
444# define R300_GB_MSPOS1__MS_Y3_SHIFT 4
445# define R300_GB_MSPOS1__MS_X4_SHIFT 8
446# define R300_GB_MSPOS1__MS_Y4_SHIFT 12
447# define R300_GB_MSPOS1__MS_X5_SHIFT 16
448# define R300_GB_MSPOS1__MS_Y5_SHIFT 20
449# define R300_GB_MSPOS1__MSBD1 24
450
451
452#define R300_GB_TILE_CONFIG 0x4018
453# define R300_GB_TILE_ENABLE (1<<0)
454# define R300_GB_TILE_PIPE_COUNT_RV300 0
455# define R300_GB_TILE_PIPE_COUNT_R300 (3<<1)
456# define R300_GB_TILE_PIPE_COUNT_R420 (7<<1)
457# define R300_GB_TILE_PIPE_COUNT_RV410 (3<<1)
458# define R300_GB_TILE_SIZE_8 0
459# define R300_GB_TILE_SIZE_16 (1<<4)
460# define R300_GB_TILE_SIZE_32 (2<<4)
461# define R300_GB_SUPER_SIZE_1 (0<<6)
462# define R300_GB_SUPER_SIZE_2 (1<<6)
463# define R300_GB_SUPER_SIZE_4 (2<<6)
464# define R300_GB_SUPER_SIZE_8 (3<<6)
465# define R300_GB_SUPER_SIZE_16 (4<<6)
466# define R300_GB_SUPER_SIZE_32 (5<<6)
467# define R300_GB_SUPER_SIZE_64 (6<<6)
468# define R300_GB_SUPER_SIZE_128 (7<<6)
469# define R300_GB_SUPER_X_SHIFT 9 /* 3 bits wide */
470# define R300_GB_SUPER_Y_SHIFT 12 /* 3 bits wide */
471# define R300_GB_SUPER_TILE_A 0
472# define R300_GB_SUPER_TILE_B (1<<15)
473# define R300_GB_SUBPIXEL_1_12 0
474# define R300_GB_SUBPIXEL_1_16 (1<<16)
475
476#define R300_GB_FIFO_SIZE 0x4024
477 /* each of the following is 2 bits wide */
478#define R300_GB_FIFO_SIZE_32 0
479#define R300_GB_FIFO_SIZE_64 1
480#define R300_GB_FIFO_SIZE_128 2
481#define R300_GB_FIFO_SIZE_256 3
482# define R300_SC_IFIFO_SIZE_SHIFT 0
483# define R300_SC_TZFIFO_SIZE_SHIFT 2
484# define R300_SC_BFIFO_SIZE_SHIFT 4
485
486# define R300_US_OFIFO_SIZE_SHIFT 12
487# define R300_US_WFIFO_SIZE_SHIFT 14
488 /* the following use the same constants as above, but meaning is
489 is times 2 (i.e. instead of 32 words it means 64 */
490# define R300_RS_TFIFO_SIZE_SHIFT 6
491# define R300_RS_CFIFO_SIZE_SHIFT 8
492# define R300_US_RAM_SIZE_SHIFT 10
493 /* watermarks, 3 bits wide */
494# define R300_RS_HIGHWATER_COL_SHIFT 16
495# define R300_RS_HIGHWATER_TEX_SHIFT 19
496# define R300_OFIFO_HIGHWATER_SHIFT 22 /* two bits only */
497# define R300_CUBE_FIFO_HIGHWATER_COL_SHIFT 24
498
499#define R300_GB_SELECT 0x401C
500# define R300_GB_FOG_SELECT_C0A 0
501# define R300_GB_FOG_SELECT_C1A 1
502# define R300_GB_FOG_SELECT_C2A 2
503# define R300_GB_FOG_SELECT_C3A 3
504# define R300_GB_FOG_SELECT_1_1_W 4
505# define R300_GB_FOG_SELECT_Z 5
506# define R300_GB_DEPTH_SELECT_Z 0
507# define R300_GB_DEPTH_SELECT_1_1_W (1<<3)
508# define R300_GB_W_SELECT_1_W 0
509# define R300_GB_W_SELECT_1 (1<<4)
510
511#define R300_GB_AA_CONFIG 0x4020
512# define R300_AA_DISABLE 0x00
513# define R300_AA_ENABLE 0x01
514# define R300_AA_SUBSAMPLES_2 0
515# define R300_AA_SUBSAMPLES_3 (1<<1)
516# define R300_AA_SUBSAMPLES_4 (2<<1)
517# define R300_AA_SUBSAMPLES_6 (3<<1)
518
519/* gap */
520
521/* Zero to flush caches. */
522#define R300_TX_INVALTAGS 0x4100
523#define R300_TX_FLUSH 0x0
524
525/* The upper enable bits are guessed, based on fglrx reported limits. */
526#define R300_TX_ENABLE 0x4104
527# define R300_TX_ENABLE_0 (1 << 0)
528# define R300_TX_ENABLE_1 (1 << 1)
529# define R300_TX_ENABLE_2 (1 << 2)
530# define R300_TX_ENABLE_3 (1 << 3)
531# define R300_TX_ENABLE_4 (1 << 4)
532# define R300_TX_ENABLE_5 (1 << 5)
533# define R300_TX_ENABLE_6 (1 << 6)
534# define R300_TX_ENABLE_7 (1 << 7)
535# define R300_TX_ENABLE_8 (1 << 8)
536# define R300_TX_ENABLE_9 (1 << 9)
537# define R300_TX_ENABLE_10 (1 << 10)
538# define R300_TX_ENABLE_11 (1 << 11)
539# define R300_TX_ENABLE_12 (1 << 12)
540# define R300_TX_ENABLE_13 (1 << 13)
541# define R300_TX_ENABLE_14 (1 << 14)
542# define R300_TX_ENABLE_15 (1 << 15)
543
544/* The pointsize is given in multiples of 6. The pointsize can be
545 * enormous: Clear() renders a single point that fills the entire
546 * framebuffer.
547 */
548#define R300_RE_POINTSIZE 0x421C
549# define R300_POINTSIZE_Y_SHIFT 0
550# define R300_POINTSIZE_Y_MASK (0xFFFF << 0) /* GUESS */
551# define R300_POINTSIZE_X_SHIFT 16
552# define R300_POINTSIZE_X_MASK (0xFFFF << 16) /* GUESS */
553# define R300_POINTSIZE_MAX (R300_POINTSIZE_Y_MASK / 6)
554
555/* The line width is given in multiples of 6.
556 * In default mode lines are classified as vertical lines.
557 * HO: horizontal
558 * VE: vertical or horizontal
559 * HO & VE: no classification
560 */
561#define R300_RE_LINE_CNT 0x4234
562# define R300_LINESIZE_SHIFT 0
563# define R300_LINESIZE_MASK (0xFFFF << 0) /* GUESS */
564# define R300_LINESIZE_MAX (R300_LINESIZE_MASK / 6)
565# define R300_LINE_CNT_HO (1 << 16)
566# define R300_LINE_CNT_VE (1 << 17)
567
568/* Some sort of scale or clamp value for texcoordless textures. */
569#define R300_RE_UNK4238 0x4238
570
571/* Something shade related */
572#define R300_RE_SHADE 0x4274
573
574#define R300_RE_SHADE_MODEL 0x4278
575# define R300_RE_SHADE_MODEL_SMOOTH 0x3aaaa
576# define R300_RE_SHADE_MODEL_FLAT 0x39595
577
578/* Dangerous */
579#define R300_RE_POLYGON_MODE 0x4288
580# define R300_PM_ENABLED (1 << 0)
581# define R300_PM_FRONT_POINT (0 << 0)
582# define R300_PM_BACK_POINT (0 << 0)
583# define R300_PM_FRONT_LINE (1 << 4)
584# define R300_PM_FRONT_FILL (1 << 5)
585# define R300_PM_BACK_LINE (1 << 7)
586# define R300_PM_BACK_FILL (1 << 8)
587
588/* Fog parameters */
589#define R300_RE_FOG_SCALE 0x4294
590#define R300_RE_FOG_START 0x4298
591
592/* Not sure why there are duplicate of factor and constant values.
593 * My best guess so far is that there are separate zbiases for test and write.
594 * Ordering might be wrong.
595 * Some of the tests indicate that fgl has a fallback implementation of zbias
596 * via pixel shaders.
597 */
598#define R300_RE_ZBIAS_CNTL 0x42A0 /* GUESS */
599#define R300_RE_ZBIAS_T_FACTOR 0x42A4
600#define R300_RE_ZBIAS_T_CONSTANT 0x42A8
601#define R300_RE_ZBIAS_W_FACTOR 0x42AC
602#define R300_RE_ZBIAS_W_CONSTANT 0x42B0
603
604/* This register needs to be set to (1<<1) for RV350 to correctly
605 * perform depth test (see --vb-triangles in r300_demo)
606 * Don't know about other chips. - Vladimir
607 * This is set to 3 when GL_POLYGON_OFFSET_FILL is on.
608 * My guess is that there are two bits for each zbias primitive
609 * (FILL, LINE, POINT).
610 * One to enable depth test and one for depth write.
611 * Yet this doesn't explain why depth writes work ...
612 */
613#define R300_RE_OCCLUSION_CNTL 0x42B4
614# define R300_OCCLUSION_ON (1<<1)
615
616#define R300_RE_CULL_CNTL 0x42B8
617# define R300_CULL_FRONT (1 << 0)
618# define R300_CULL_BACK (1 << 1)
619# define R300_FRONT_FACE_CCW (0 << 2)
620# define R300_FRONT_FACE_CW (1 << 2)
621
622
623/* BEGIN: Rasterization / Interpolators - many guesses */
624
625/* 0_UNKNOWN_18 has always been set except for clear operations.
626 * TC_CNT is the number of incoming texture coordinate sets (i.e. it depends
627 * on the vertex program, *not* the fragment program)
628 */
629#define R300_RS_CNTL_0 0x4300
630# define R300_RS_CNTL_TC_CNT_SHIFT 2
631# define R300_RS_CNTL_TC_CNT_MASK (7 << 2)
632 /* number of color interpolators used */
633# define R300_RS_CNTL_CI_CNT_SHIFT 7
634# define R300_RS_CNTL_0_UNKNOWN_18 (1 << 18)
635 /* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n
636 register. */
637#define R300_RS_CNTL_1 0x4304
638
639/* gap */
640
641/* Only used for texture coordinates.
642 * Use the source field to route texture coordinate input from the
643 * vertex program to the desired interpolator. Note that the source
644 * field is relative to the outputs the vertex program *actually*
645 * writes. If a vertex program only writes texcoord[1], this will
646 * be source index 0.
647 * Set INTERP_USED on all interpolators that produce data used by
648 * the fragment program. INTERP_USED looks like a swizzling mask,
649 * but I haven't seen it used that way.
650 *
651 * Note: The _UNKNOWN constants are always set in their respective
652 * register. I don't know if this is necessary.
653 */
654#define R300_RS_INTERP_0 0x4310
655#define R300_RS_INTERP_1 0x4314
656# define R300_RS_INTERP_1_UNKNOWN 0x40
657#define R300_RS_INTERP_2 0x4318
658# define R300_RS_INTERP_2_UNKNOWN 0x80
659#define R300_RS_INTERP_3 0x431C
660# define R300_RS_INTERP_3_UNKNOWN 0xC0
661#define R300_RS_INTERP_4 0x4320
662#define R300_RS_INTERP_5 0x4324
663#define R300_RS_INTERP_6 0x4328
664#define R300_RS_INTERP_7 0x432C
665# define R300_RS_INTERP_SRC_SHIFT 2
666# define R300_RS_INTERP_SRC_MASK (7 << 2)
667# define R300_RS_INTERP_USED 0x00D10000
668
669/* These DWORDs control how vertex data is routed into fragment program
670 * registers, after interpolators.
671 */
672#define R300_RS_ROUTE_0 0x4330
673#define R300_RS_ROUTE_1 0x4334
674#define R300_RS_ROUTE_2 0x4338
675#define R300_RS_ROUTE_3 0x433C /* GUESS */
676#define R300_RS_ROUTE_4 0x4340 /* GUESS */
677#define R300_RS_ROUTE_5 0x4344 /* GUESS */
678#define R300_RS_ROUTE_6 0x4348 /* GUESS */
679#define R300_RS_ROUTE_7 0x434C /* GUESS */
680# define R300_RS_ROUTE_SOURCE_INTERP_0 0
681# define R300_RS_ROUTE_SOURCE_INTERP_1 1
682# define R300_RS_ROUTE_SOURCE_INTERP_2 2
683# define R300_RS_ROUTE_SOURCE_INTERP_3 3
684# define R300_RS_ROUTE_SOURCE_INTERP_4 4
685# define R300_RS_ROUTE_SOURCE_INTERP_5 5 /* GUESS */
686# define R300_RS_ROUTE_SOURCE_INTERP_6 6 /* GUESS */
687# define R300_RS_ROUTE_SOURCE_INTERP_7 7 /* GUESS */
688# define R300_RS_ROUTE_ENABLE (1 << 3) /* GUESS */
689# define R300_RS_ROUTE_DEST_SHIFT 6
690# define R300_RS_ROUTE_DEST_MASK (31 << 6) /* GUESS */
691
692/* Special handling for color: When the fragment program uses color,
693 * the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the
694 * color register index.
695 *
696 * Apperently you may set the R300_RS_ROUTE_0_COLOR bit, but not provide any
697 * R300_RS_ROUTE_0_COLOR_DEST value; this setup is used for clearing the state.
698 * See r300_ioctl.c:r300EmitClearState. I'm not sure if this setup is strictly
699 * correct or not. - Oliver.
700 */
701# define R300_RS_ROUTE_0_COLOR (1 << 14)
702# define R300_RS_ROUTE_0_COLOR_DEST_SHIFT 17
703# define R300_RS_ROUTE_0_COLOR_DEST_MASK (31 << 17) /* GUESS */
704/* As above, but for secondary color */
705# define R300_RS_ROUTE_1_COLOR1 (1 << 14)
706# define R300_RS_ROUTE_1_COLOR1_DEST_SHIFT 17
707# define R300_RS_ROUTE_1_COLOR1_DEST_MASK (31 << 17)
708# define R300_RS_ROUTE_1_UNKNOWN11 (1 << 11)
709/* END: Rasterization / Interpolators - many guesses */
710
711/* Hierarchical Z Enable */
712#define R300_SC_HYPERZ 0x43a4
713# define R300_SC_HYPERZ_DISABLE (0 << 0)
714# define R300_SC_HYPERZ_ENABLE (1 << 0)
715# define R300_SC_HYPERZ_MIN (0 << 1)
716# define R300_SC_HYPERZ_MAX (1 << 1)
717# define R300_SC_HYPERZ_ADJ_256 (0 << 2)
718# define R300_SC_HYPERZ_ADJ_128 (1 << 2)
719# define R300_SC_HYPERZ_ADJ_64 (2 << 2)
720# define R300_SC_HYPERZ_ADJ_32 (3 << 2)
721# define R300_SC_HYPERZ_ADJ_16 (4 << 2)
722# define R300_SC_HYPERZ_ADJ_8 (5 << 2)
723# define R300_SC_HYPERZ_ADJ_4 (6 << 2)
724# define R300_SC_HYPERZ_ADJ_2 (7 << 2)
725# define R300_SC_HYPERZ_HZ_Z0MIN_NO (0 << 5)
726# define R300_SC_HYPERZ_HZ_Z0MIN (1 << 5)
727# define R300_SC_HYPERZ_HZ_Z0MAX_NO (0 << 6)
728# define R300_SC_HYPERZ_HZ_Z0MAX (1 << 6)
729
730#define R300_SC_EDGERULE 0x43a8
731
732/* BEGIN: Scissors and cliprects */
733
734/* There are four clipping rectangles. Their corner coordinates are inclusive.
735 * Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending
736 * on whether the pixel is inside cliprects 0-3, respectively. For example,
737 * if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned
738 * the number 3 (binary 0011).
739 * Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set,
740 * the pixel is rasterized.
741 *
742 * In addition to this, there is a scissors rectangle. Only pixels inside the
743 * scissors rectangle are drawn. (coordinates are inclusive)
744 *
745 * For some reason, the top-left corner of the framebuffer is at (1440, 1440)
746 * for the purpose of clipping and scissors.
747 */
748#define R300_RE_CLIPRECT_TL_0 0x43B0
749#define R300_RE_CLIPRECT_BR_0 0x43B4
750#define R300_RE_CLIPRECT_TL_1 0x43B8
751#define R300_RE_CLIPRECT_BR_1 0x43BC
752#define R300_RE_CLIPRECT_TL_2 0x43C0
753#define R300_RE_CLIPRECT_BR_2 0x43C4
754#define R300_RE_CLIPRECT_TL_3 0x43C8
755#define R300_RE_CLIPRECT_BR_3 0x43CC
756# define R300_CLIPRECT_OFFSET 1440
757# define R300_CLIPRECT_MASK 0x1FFF
758# define R300_CLIPRECT_X_SHIFT 0
759# define R300_CLIPRECT_X_MASK (0x1FFF << 0)
760# define R300_CLIPRECT_Y_SHIFT 13
761# define R300_CLIPRECT_Y_MASK (0x1FFF << 13)
762#define R300_RE_CLIPRECT_CNTL 0x43D0
763# define R300_CLIP_OUT (1 << 0)
764# define R300_CLIP_0 (1 << 1)
765# define R300_CLIP_1 (1 << 2)
766# define R300_CLIP_10 (1 << 3)
767# define R300_CLIP_2 (1 << 4)
768# define R300_CLIP_20 (1 << 5)
769# define R300_CLIP_21 (1 << 6)
770# define R300_CLIP_210 (1 << 7)
771# define R300_CLIP_3 (1 << 8)
772# define R300_CLIP_30 (1 << 9)
773# define R300_CLIP_31 (1 << 10)
774# define R300_CLIP_310 (1 << 11)
775# define R300_CLIP_32 (1 << 12)
776# define R300_CLIP_320 (1 << 13)
777# define R300_CLIP_321 (1 << 14)
778# define R300_CLIP_3210 (1 << 15)
779
780/* gap */
781
782#define R300_RE_SCISSORS_TL 0x43E0
783#define R300_RE_SCISSORS_BR 0x43E4
784# define R300_SCISSORS_OFFSET 1440
785# define R300_SCISSORS_X_SHIFT 0
786# define R300_SCISSORS_X_MASK (0x1FFF << 0)
787# define R300_SCISSORS_Y_SHIFT 13
788# define R300_SCISSORS_Y_MASK (0x1FFF << 13)
789/* END: Scissors and cliprects */
790
791/* BEGIN: Texture specification */
792
793/*
794 * The texture specification dwords are grouped by meaning and not by texture
795 * unit. This means that e.g. the offset for texture image unit N is found in
796 * register TX_OFFSET_0 + (4*N)
797 */
798#define R300_TX_FILTER_0 0x4400
799# define R300_TX_REPEAT 0
800# define R300_TX_MIRRORED 1
801# define R300_TX_CLAMP 4
802# define R300_TX_CLAMP_TO_EDGE 2
803# define R300_TX_CLAMP_TO_BORDER 6
804# define R300_TX_WRAP_S_SHIFT 0
805# define R300_TX_WRAP_S_MASK (7 << 0)
806# define R300_TX_WRAP_T_SHIFT 3
807# define R300_TX_WRAP_T_MASK (7 << 3)
808# define R300_TX_WRAP_Q_SHIFT 6
809# define R300_TX_WRAP_Q_MASK (7 << 6)
810# define R300_TX_MAG_FILTER_NEAREST (1 << 9)
811# define R300_TX_MAG_FILTER_LINEAR (2 << 9)
812# define R300_TX_MAG_FILTER_MASK (3 << 9)
813# define R300_TX_MIN_FILTER_NEAREST (1 << 11)
814# define R300_TX_MIN_FILTER_LINEAR (2 << 11)
815# define R300_TX_MIN_FILTER_NEAREST_MIP_NEAREST (5 << 11)
816# define R300_TX_MIN_FILTER_NEAREST_MIP_LINEAR (9 << 11)
817# define R300_TX_MIN_FILTER_LINEAR_MIP_NEAREST (6 << 11)
818# define R300_TX_MIN_FILTER_LINEAR_MIP_LINEAR (10 << 11)
819
820/* NOTE: NEAREST doesn't seem to exist.
821 * Im not seting MAG_FILTER_MASK and (3 << 11) on for all
822 * anisotropy modes because that would void selected mag filter
823 */
824# define R300_TX_MIN_FILTER_ANISO_NEAREST (0 << 13)
825# define R300_TX_MIN_FILTER_ANISO_LINEAR (0 << 13)
826# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST (1 << 13)
827# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR (2 << 13)
828# define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) )
829# define R300_TX_MAX_ANISO_1_TO_1 (0 << 21)
830# define R300_TX_MAX_ANISO_2_TO_1 (2 << 21)
831# define R300_TX_MAX_ANISO_4_TO_1 (4 << 21)
832# define R300_TX_MAX_ANISO_8_TO_1 (6 << 21)
833# define R300_TX_MAX_ANISO_16_TO_1 (8 << 21)
834# define R300_TX_MAX_ANISO_MASK (14 << 21)
835
836#define R300_TX_FILTER1_0 0x4440
837# define R300_CHROMA_KEY_MODE_DISABLE 0
838# define R300_CHROMA_KEY_FORCE 1
839# define R300_CHROMA_KEY_BLEND 2
840# define R300_MC_ROUND_NORMAL (0<<2)
841# define R300_MC_ROUND_MPEG4 (1<<2)
842# define R300_LOD_BIAS_MASK 0x1fff
843# define R300_EDGE_ANISO_EDGE_DIAG (0<<13)
844# define R300_EDGE_ANISO_EDGE_ONLY (1<<13)
845# define R300_MC_COORD_TRUNCATE_DISABLE (0<<14)
846# define R300_MC_COORD_TRUNCATE_MPEG (1<<14)
847# define R300_TX_TRI_PERF_0_8 (0<<15)
848# define R300_TX_TRI_PERF_1_8 (1<<15)
849# define R300_TX_TRI_PERF_1_4 (2<<15)
850# define R300_TX_TRI_PERF_3_8 (3<<15)
851# define R300_ANISO_THRESHOLD_MASK (7<<17)
852
853#define R300_TX_SIZE_0 0x4480
854# define R300_TX_WIDTHMASK_SHIFT 0
855# define R300_TX_WIDTHMASK_MASK (2047 << 0)
856# define R300_TX_HEIGHTMASK_SHIFT 11
857# define R300_TX_HEIGHTMASK_MASK (2047 << 11)
858# define R300_TX_UNK23 (1 << 23)
859# define R300_TX_MAX_MIP_LEVEL_SHIFT 26
860# define R300_TX_MAX_MIP_LEVEL_MASK (0xf << 26)
861# define R300_TX_SIZE_PROJECTED (1<<30)
862# define R300_TX_SIZE_TXPITCH_EN (1<<31)
863#define R300_TX_FORMAT_0 0x44C0
864 /* The interpretation of the format word by Wladimir van der Laan */
865 /* The X, Y, Z and W refer to the layout of the components.
866 They are given meanings as R, G, B and Alpha by the swizzle
867 specification */
868# define R300_TX_FORMAT_X8 0x0
869# define R300_TX_FORMAT_X16 0x1
870# define R300_TX_FORMAT_Y4X4 0x2
871# define R300_TX_FORMAT_Y8X8 0x3
872# define R300_TX_FORMAT_Y16X16 0x4
873# define R300_TX_FORMAT_Z3Y3X2 0x5
874# define R300_TX_FORMAT_Z5Y6X5 0x6
875# define R300_TX_FORMAT_Z6Y5X5 0x7
876# define R300_TX_FORMAT_Z11Y11X10 0x8
877# define R300_TX_FORMAT_Z10Y11X11 0x9
878# define R300_TX_FORMAT_W4Z4Y4X4 0xA
879# define R300_TX_FORMAT_W1Z5Y5X5 0xB
880# define R300_TX_FORMAT_W8Z8Y8X8 0xC
881# define R300_TX_FORMAT_W2Z10Y10X10 0xD
882# define R300_TX_FORMAT_W16Z16Y16X16 0xE
883# define R300_TX_FORMAT_DXT1 0xF
884# define R300_TX_FORMAT_DXT3 0x10
885# define R300_TX_FORMAT_DXT5 0x11
886# define R300_TX_FORMAT_D3DMFT_CxV8U8 0x12 /* no swizzle */
887# define R300_TX_FORMAT_A8R8G8B8 0x13 /* no swizzle */
888# define R300_TX_FORMAT_B8G8_B8G8 0x14 /* no swizzle */
889# define R300_TX_FORMAT_G8R8_G8B8 0x15 /* no swizzle */
890 /* 0x16 - some 16 bit green format.. ?? */
891# define R300_TX_FORMAT_UNK25 (1 << 25) /* no swizzle */
892# define R300_TX_FORMAT_CUBIC_MAP (1 << 26)
893
894 /* gap */
895 /* Floating point formats */
896 /* Note - hardware supports both 16 and 32 bit floating point */
897# define R300_TX_FORMAT_FL_I16 0x18
898# define R300_TX_FORMAT_FL_I16A16 0x19
899# define R300_TX_FORMAT_FL_R16G16B16A16 0x1A
900# define R300_TX_FORMAT_FL_I32 0x1B
901# define R300_TX_FORMAT_FL_I32A32 0x1C
902# define R300_TX_FORMAT_FL_R32G32B32A32 0x1D
903# define R300_TX_FORMAT_ATI2N 0x1F
904 /* alpha modes, convenience mostly */
905 /* if you have alpha, pick constant appropriate to the
906 number of channels (1 for I8, 2 for I8A8, 4 for R8G8B8A8, etc */
907# define R300_TX_FORMAT_ALPHA_1CH 0x000
908# define R300_TX_FORMAT_ALPHA_2CH 0x200
909# define R300_TX_FORMAT_ALPHA_4CH 0x600
910# define R300_TX_FORMAT_ALPHA_NONE 0xA00
911 /* Swizzling */
912 /* constants */
913# define R300_TX_FORMAT_X 0
914# define R300_TX_FORMAT_Y 1
915# define R300_TX_FORMAT_Z 2
916# define R300_TX_FORMAT_W 3
917# define R300_TX_FORMAT_ZERO 4
918# define R300_TX_FORMAT_ONE 5
919 /* 2.0*Z, everything above 1.0 is set to 0.0 */
920# define R300_TX_FORMAT_CUT_Z 6
921 /* 2.0*W, everything above 1.0 is set to 0.0 */
922# define R300_TX_FORMAT_CUT_W 7
923
924# define R300_TX_FORMAT_B_SHIFT 18
925# define R300_TX_FORMAT_G_SHIFT 15
926# define R300_TX_FORMAT_R_SHIFT 12
927# define R300_TX_FORMAT_A_SHIFT 9
928 /* Convenience macro to take care of layout and swizzling */
929# define R300_EASY_TX_FORMAT(B, G, R, A, FMT) ( \
930 ((R300_TX_FORMAT_##B)<<R300_TX_FORMAT_B_SHIFT) \
931 | ((R300_TX_FORMAT_##G)<<R300_TX_FORMAT_G_SHIFT) \
932 | ((R300_TX_FORMAT_##R)<<R300_TX_FORMAT_R_SHIFT) \
933 | ((R300_TX_FORMAT_##A)<<R300_TX_FORMAT_A_SHIFT) \
934 | (R300_TX_FORMAT_##FMT) \
935 )
936 /* These can be ORed with result of R300_EASY_TX_FORMAT()
937 We don't really know what they do. Take values from a
938 constant color ? */
939# define R300_TX_FORMAT_CONST_X (1<<5)
940# define R300_TX_FORMAT_CONST_Y (2<<5)
941# define R300_TX_FORMAT_CONST_Z (4<<5)
942# define R300_TX_FORMAT_CONST_W (8<<5)
943
944# define R300_TX_FORMAT_YUV_MODE 0x00800000
945
946#define R300_TX_PITCH_0 0x4500 /* obvious missing in gap */
947#define R300_TX_OFFSET_0 0x4540
948 /* BEGIN: Guess from R200 */
949# define R300_TXO_ENDIAN_NO_SWAP (0 << 0)
950# define R300_TXO_ENDIAN_BYTE_SWAP (1 << 0)
951# define R300_TXO_ENDIAN_WORD_SWAP (2 << 0)
952# define R300_TXO_ENDIAN_HALFDW_SWAP (3 << 0)
953# define R300_TXO_MACRO_TILE (1 << 2)
954# define R300_TXO_MICRO_TILE (1 << 3)
955# define R300_TXO_MICRO_TILE_SQUARE (2 << 3)
956# define R300_TXO_OFFSET_MASK 0xffffffe0
957# define R300_TXO_OFFSET_SHIFT 5
958 /* END: Guess from R200 */
959
960/* 32 bit chroma key */
961#define R300_TX_CHROMA_KEY_0 0x4580
962/* ff00ff00 == { 0, 1.0, 0, 1.0 } */
963#define R300_TX_BORDER_COLOR_0 0x45C0
964
965/* END: Texture specification */
966
967/* BEGIN: Fragment program instruction set */
968
969/* Fragment programs are written directly into register space.
970 * There are separate instruction streams for texture instructions and ALU
971 * instructions.
972 * In order to synchronize these streams, the program is divided into up
973 * to 4 nodes. Each node begins with a number of TEX operations, followed
974 * by a number of ALU operations.
975 * The first node can have zero TEX ops, all subsequent nodes must have at
976 * least
977 * one TEX ops.
978 * All nodes must have at least one ALU op.
979 *
980 * The index of the last node is stored in PFS_CNTL_0: A value of 0 means
981 * 1 node, a value of 3 means 4 nodes.
982 * The total amount of instructions is defined in PFS_CNTL_2. The offsets are
983 * offsets into the respective instruction streams, while *_END points to the
984 * last instruction relative to this offset.
985 */
986#define R300_PFS_CNTL_0 0x4600
987# define R300_PFS_CNTL_LAST_NODES_SHIFT 0
988# define R300_PFS_CNTL_LAST_NODES_MASK (3 << 0)
989# define R300_PFS_CNTL_FIRST_NODE_HAS_TEX (1 << 3)
990#define R300_PFS_CNTL_1 0x4604
991/* There is an unshifted value here which has so far always been equal to the
992 * index of the highest used temporary register.
993 */
994#define R300_PFS_CNTL_2 0x4608
995# define R300_PFS_CNTL_ALU_OFFSET_SHIFT 0
996# define R300_PFS_CNTL_ALU_OFFSET_MASK (63 << 0)
997# define R300_PFS_CNTL_ALU_END_SHIFT 6
998# define R300_PFS_CNTL_ALU_END_MASK (63 << 6)
999# define R300_PFS_CNTL_TEX_OFFSET_SHIFT 12
1000# define R300_PFS_CNTL_TEX_OFFSET_MASK (31 << 12) /* GUESS */
1001# define R300_PFS_CNTL_TEX_END_SHIFT 18
1002# define R300_PFS_CNTL_TEX_END_MASK (31 << 18) /* GUESS */
1003
1004/* gap */
1005
1006/* Nodes are stored backwards. The last active node is always stored in
1007 * PFS_NODE_3.
1008 * Example: In a 2-node program, NODE_0 and NODE_1 are set to 0. The
1009 * first node is stored in NODE_2, the second node is stored in NODE_3.
1010 *
1011 * Offsets are relative to the master offset from PFS_CNTL_2.
1012 */
1013#define R300_PFS_NODE_0 0x4610
1014#define R300_PFS_NODE_1 0x4614
1015#define R300_PFS_NODE_2 0x4618
1016#define R300_PFS_NODE_3 0x461C
1017# define R300_PFS_NODE_ALU_OFFSET_SHIFT 0
1018# define R300_PFS_NODE_ALU_OFFSET_MASK (63 << 0)
1019# define R300_PFS_NODE_ALU_END_SHIFT 6
1020# define R300_PFS_NODE_ALU_END_MASK (63 << 6)
1021# define R300_PFS_NODE_TEX_OFFSET_SHIFT 12
1022# define R300_PFS_NODE_TEX_OFFSET_MASK (31 << 12)
1023# define R300_PFS_NODE_TEX_END_SHIFT 17
1024# define R300_PFS_NODE_TEX_END_MASK (31 << 17)
1025# define R300_PFS_NODE_OUTPUT_COLOR (1 << 22)
1026# define R300_PFS_NODE_OUTPUT_DEPTH (1 << 23)
1027
1028/* TEX
1029 * As far as I can tell, texture instructions cannot write into output
1030 * registers directly. A subsequent ALU instruction is always necessary,
1031 * even if it's just MAD o0, r0, 1, 0
1032 */
1033#define R300_PFS_TEXI_0 0x4620
1034# define R300_FPITX_SRC_SHIFT 0
1035# define R300_FPITX_SRC_MASK (31 << 0)
1036 /* GUESS */
1037# define R300_FPITX_SRC_CONST (1 << 5)
1038# define R300_FPITX_DST_SHIFT 6
1039# define R300_FPITX_DST_MASK (31 << 6)
1040# define R300_FPITX_IMAGE_SHIFT 11
1041 /* GUESS based on layout and native limits */
1042# define R300_FPITX_IMAGE_MASK (15 << 11)
1043/* Unsure if these are opcodes, or some kind of bitfield, but this is how
1044 * they were set when I checked
1045 */
1046# define R300_FPITX_OPCODE_SHIFT 15
1047# define R300_FPITX_OP_TEX 1
1048# define R300_FPITX_OP_KIL 2
1049# define R300_FPITX_OP_TXP 3
1050# define R300_FPITX_OP_TXB 4
1051# define R300_FPITX_OPCODE_MASK (7 << 15)
1052
1053/* ALU
1054 * The ALU instructions register blocks are enumerated according to the order
1055 * in which fglrx. I assume there is space for 64 instructions, since
1056 * each block has space for a maximum of 64 DWORDs, and this matches reported
1057 * native limits.
1058 *
1059 * The basic functional block seems to be one MAD for each color and alpha,
1060 * and an adder that adds all components after the MUL.
1061 * - ADD, MUL, MAD etc.: use MAD with appropriate neutral operands
1062 * - DP4: Use OUTC_DP4, OUTA_DP4
1063 * - DP3: Use OUTC_DP3, OUTA_DP4, appropriate alpha operands
1064 * - DPH: Use OUTC_DP4, OUTA_DP4, appropriate alpha operands
1065 * - CMPH: If ARG2 > 0.5, return ARG0, else return ARG1
1066 * - CMP: If ARG2 < 0, return ARG1, else return ARG0
1067 * - FLR: use FRC+MAD
1068 * - XPD: use MAD+MAD
1069 * - SGE, SLT: use MAD+CMP
1070 * - RSQ: use ABS modifier for argument
1071 * - Use OUTC_REPL_ALPHA to write results of an alpha-only operation
1072 * (e.g. RCP) into color register
1073 * - apparently, there's no quick DST operation
1074 * - fglrx set FPI2_UNKNOWN_31 on a "MAD fragment.color, tmp0, tmp1, tmp2"
1075 * - fglrx set FPI2_UNKNOWN_31 on a "MAX r2, r1, c0"
1076 * - fglrx once set FPI0_UNKNOWN_31 on a "FRC r1, r1"
1077 *
1078 * Operand selection
1079 * First stage selects three sources from the available registers and
1080 * constant parameters. This is defined in INSTR1 (color) and INSTR3 (alpha).
1081 * fglrx sorts the three source fields: Registers before constants,
1082 * lower indices before higher indices; I do not know whether this is
1083 * necessary.
1084 *
1085 * fglrx fills unused sources with "read constant 0"
1086 * According to specs, you cannot select more than two different constants.
1087 *
1088 * Second stage selects the operands from the sources. This is defined in
1089 * INSTR0 (color) and INSTR2 (alpha). You can also select the special constants
1090 * zero and one.
1091 * Swizzling and negation happens in this stage, as well.
1092 *
1093 * Important: Color and alpha seem to be mostly separate, i.e. their sources
1094 * selection appears to be fully independent (the register storage is probably
1095 * physically split into a color and an alpha section).
1096 * However (because of the apparent physical split), there is some interaction
1097 * WRT swizzling. If, for example, you want to load an R component into an
1098 * Alpha operand, this R component is taken from a *color* source, not from
1099 * an alpha source. The corresponding register doesn't even have to appear in
1100 * the alpha sources list. (I hope this all makes sense to you)
1101 *
1102 * Destination selection
1103 * The destination register index is in FPI1 (color) and FPI3 (alpha)
1104 * together with enable bits.
1105 * There are separate enable bits for writing into temporary registers
1106 * (DSTC_REG_* /DSTA_REG) and program output registers (DSTC_OUTPUT_*
1107 * /DSTA_OUTPUT). You can write to both at once, or not write at all (the
1108 * same index must be used for both).
1109 *
1110 * Note: There is a special form for LRP
1111 * - Argument order is the same as in ARB_fragment_program.
1112 * - Operation is MAD
1113 * - ARG1 is set to ARGC_SRC1C_LRP/ARGC_SRC1A_LRP
1114 * - Set FPI0/FPI2_SPECIAL_LRP
1115 * Arbitrary LRP (including support for swizzling) requires vanilla MAD+MAD
1116 */
1117#define R300_PFS_INSTR1_0 0x46C0
1118# define R300_FPI1_SRC0C_SHIFT 0
1119# define R300_FPI1_SRC0C_MASK (31 << 0)
1120# define R300_FPI1_SRC0C_CONST (1 << 5)
1121# define R300_FPI1_SRC1C_SHIFT 6
1122# define R300_FPI1_SRC1C_MASK (31 << 6)
1123# define R300_FPI1_SRC1C_CONST (1 << 11)
1124# define R300_FPI1_SRC2C_SHIFT 12
1125# define R300_FPI1_SRC2C_MASK (31 << 12)
1126# define R300_FPI1_SRC2C_CONST (1 << 17)
1127# define R300_FPI1_SRC_MASK 0x0003ffff
1128# define R300_FPI1_DSTC_SHIFT 18
1129# define R300_FPI1_DSTC_MASK (31 << 18)
1130# define R300_FPI1_DSTC_REG_MASK_SHIFT 23
1131# define R300_FPI1_DSTC_REG_X (1 << 23)
1132# define R300_FPI1_DSTC_REG_Y (1 << 24)
1133# define R300_FPI1_DSTC_REG_Z (1 << 25)
1134# define R300_FPI1_DSTC_OUTPUT_MASK_SHIFT 26
1135# define R300_FPI1_DSTC_OUTPUT_X (1 << 26)
1136# define R300_FPI1_DSTC_OUTPUT_Y (1 << 27)
1137# define R300_FPI1_DSTC_OUTPUT_Z (1 << 28)
1138
1139#define R300_PFS_INSTR3_0 0x47C0
1140# define R300_FPI3_SRC0A_SHIFT 0
1141# define R300_FPI3_SRC0A_MASK (31 << 0)
1142# define R300_FPI3_SRC0A_CONST (1 << 5)
1143# define R300_FPI3_SRC1A_SHIFT 6
1144# define R300_FPI3_SRC1A_MASK (31 << 6)
1145# define R300_FPI3_SRC1A_CONST (1 << 11)
1146# define R300_FPI3_SRC2A_SHIFT 12
1147# define R300_FPI3_SRC2A_MASK (31 << 12)
1148# define R300_FPI3_SRC2A_CONST (1 << 17)
1149# define R300_FPI3_SRC_MASK 0x0003ffff
1150# define R300_FPI3_DSTA_SHIFT 18
1151# define R300_FPI3_DSTA_MASK (31 << 18)
1152# define R300_FPI3_DSTA_REG (1 << 23)
1153# define R300_FPI3_DSTA_OUTPUT (1 << 24)
1154# define R300_FPI3_DSTA_DEPTH (1 << 27)
1155
1156#define R300_PFS_INSTR0_0 0x48C0
1157# define R300_FPI0_ARGC_SRC0C_XYZ 0
1158# define R300_FPI0_ARGC_SRC0C_XXX 1
1159# define R300_FPI0_ARGC_SRC0C_YYY 2
1160# define R300_FPI0_ARGC_SRC0C_ZZZ 3
1161# define R300_FPI0_ARGC_SRC1C_XYZ 4
1162# define R300_FPI0_ARGC_SRC1C_XXX 5
1163# define R300_FPI0_ARGC_SRC1C_YYY 6
1164# define R300_FPI0_ARGC_SRC1C_ZZZ 7
1165# define R300_FPI0_ARGC_SRC2C_XYZ 8
1166# define R300_FPI0_ARGC_SRC2C_XXX 9
1167# define R300_FPI0_ARGC_SRC2C_YYY 10
1168# define R300_FPI0_ARGC_SRC2C_ZZZ 11
1169# define R300_FPI0_ARGC_SRC0A 12
1170# define R300_FPI0_ARGC_SRC1A 13
1171# define R300_FPI0_ARGC_SRC2A 14
1172# define R300_FPI0_ARGC_SRC1C_LRP 15
1173# define R300_FPI0_ARGC_ZERO 20
1174# define R300_FPI0_ARGC_ONE 21
1175 /* GUESS */
1176# define R300_FPI0_ARGC_HALF 22
1177# define R300_FPI0_ARGC_SRC0C_YZX 23
1178# define R300_FPI0_ARGC_SRC1C_YZX 24
1179# define R300_FPI0_ARGC_SRC2C_YZX 25
1180# define R300_FPI0_ARGC_SRC0C_ZXY 26
1181# define R300_FPI0_ARGC_SRC1C_ZXY 27
1182# define R300_FPI0_ARGC_SRC2C_ZXY 28
1183# define R300_FPI0_ARGC_SRC0CA_WZY 29
1184# define R300_FPI0_ARGC_SRC1CA_WZY 30
1185# define R300_FPI0_ARGC_SRC2CA_WZY 31
1186
1187# define R300_FPI0_ARG0C_SHIFT 0
1188# define R300_FPI0_ARG0C_MASK (31 << 0)
1189# define R300_FPI0_ARG0C_NEG (1 << 5)
1190# define R300_FPI0_ARG0C_ABS (1 << 6)
1191# define R300_FPI0_ARG1C_SHIFT 7
1192# define R300_FPI0_ARG1C_MASK (31 << 7)
1193# define R300_FPI0_ARG1C_NEG (1 << 12)
1194# define R300_FPI0_ARG1C_ABS (1 << 13)
1195# define R300_FPI0_ARG2C_SHIFT 14
1196# define R300_FPI0_ARG2C_MASK (31 << 14)
1197# define R300_FPI0_ARG2C_NEG (1 << 19)
1198# define R300_FPI0_ARG2C_ABS (1 << 20)
1199# define R300_FPI0_SPECIAL_LRP (1 << 21)
1200# define R300_FPI0_OUTC_MAD (0 << 23)
1201# define R300_FPI0_OUTC_DP3 (1 << 23)
1202# define R300_FPI0_OUTC_DP4 (2 << 23)
1203# define R300_FPI0_OUTC_MIN (4 << 23)
1204# define R300_FPI0_OUTC_MAX (5 << 23)
1205# define R300_FPI0_OUTC_CMPH (7 << 23)
1206# define R300_FPI0_OUTC_CMP (8 << 23)
1207# define R300_FPI0_OUTC_FRC (9 << 23)
1208# define R300_FPI0_OUTC_REPL_ALPHA (10 << 23)
1209# define R300_FPI0_OUTC_SAT (1 << 30)
1210# define R300_FPI0_INSERT_NOP (1 << 31)
1211
1212#define R300_PFS_INSTR2_0 0x49C0
1213# define R300_FPI2_ARGA_SRC0C_X 0
1214# define R300_FPI2_ARGA_SRC0C_Y 1
1215# define R300_FPI2_ARGA_SRC0C_Z 2
1216# define R300_FPI2_ARGA_SRC1C_X 3
1217# define R300_FPI2_ARGA_SRC1C_Y 4
1218# define R300_FPI2_ARGA_SRC1C_Z 5
1219# define R300_FPI2_ARGA_SRC2C_X 6
1220# define R300_FPI2_ARGA_SRC2C_Y 7
1221# define R300_FPI2_ARGA_SRC2C_Z 8
1222# define R300_FPI2_ARGA_SRC0A 9
1223# define R300_FPI2_ARGA_SRC1A 10
1224# define R300_FPI2_ARGA_SRC2A 11
1225# define R300_FPI2_ARGA_SRC1A_LRP 15
1226# define R300_FPI2_ARGA_ZERO 16
1227# define R300_FPI2_ARGA_ONE 17
1228 /* GUESS */
1229# define R300_FPI2_ARGA_HALF 18
1230# define R300_FPI2_ARG0A_SHIFT 0
1231# define R300_FPI2_ARG0A_MASK (31 << 0)
1232# define R300_FPI2_ARG0A_NEG (1 << 5)
1233 /* GUESS */
1234# define R300_FPI2_ARG0A_ABS (1 << 6)
1235# define R300_FPI2_ARG1A_SHIFT 7
1236# define R300_FPI2_ARG1A_MASK (31 << 7)
1237# define R300_FPI2_ARG1A_NEG (1 << 12)
1238 /* GUESS */
1239# define R300_FPI2_ARG1A_ABS (1 << 13)
1240# define R300_FPI2_ARG2A_SHIFT 14
1241# define R300_FPI2_ARG2A_MASK (31 << 14)
1242# define R300_FPI2_ARG2A_NEG (1 << 19)
1243 /* GUESS */
1244# define R300_FPI2_ARG2A_ABS (1 << 20)
1245# define R300_FPI2_SPECIAL_LRP (1 << 21)
1246# define R300_FPI2_OUTA_MAD (0 << 23)
1247# define R300_FPI2_OUTA_DP4 (1 << 23)
1248# define R300_FPI2_OUTA_MIN (2 << 23)
1249# define R300_FPI2_OUTA_MAX (3 << 23)
1250# define R300_FPI2_OUTA_CMP (6 << 23)
1251# define R300_FPI2_OUTA_FRC (7 << 23)
1252# define R300_FPI2_OUTA_EX2 (8 << 23)
1253# define R300_FPI2_OUTA_LG2 (9 << 23)
1254# define R300_FPI2_OUTA_RCP (10 << 23)
1255# define R300_FPI2_OUTA_RSQ (11 << 23)
1256# define R300_FPI2_OUTA_SAT (1 << 30)
1257# define R300_FPI2_UNKNOWN_31 (1 << 31)
1258/* END: Fragment program instruction set */
1259
1260/* Fog state and color */
1261#define R300_RE_FOG_STATE 0x4BC0
1262# define R300_FOG_ENABLE (1 << 0)
1263# define R300_FOG_MODE_LINEAR (0 << 1)
1264# define R300_FOG_MODE_EXP (1 << 1)
1265# define R300_FOG_MODE_EXP2 (2 << 1)
1266# define R300_FOG_MODE_MASK (3 << 1)
1267#define R300_FOG_COLOR_R 0x4BC8
1268#define R300_FOG_COLOR_G 0x4BCC
1269#define R300_FOG_COLOR_B 0x4BD0
1270
1271#define R300_PP_ALPHA_TEST 0x4BD4
1272# define R300_REF_ALPHA_MASK 0x000000ff
1273# define R300_ALPHA_TEST_FAIL (0 << 8)
1274# define R300_ALPHA_TEST_LESS (1 << 8)
1275# define R300_ALPHA_TEST_LEQUAL (3 << 8)
1276# define R300_ALPHA_TEST_EQUAL (2 << 8)
1277# define R300_ALPHA_TEST_GEQUAL (6 << 8)
1278# define R300_ALPHA_TEST_GREATER (4 << 8)
1279# define R300_ALPHA_TEST_NEQUAL (5 << 8)
1280# define R300_ALPHA_TEST_PASS (7 << 8)
1281# define R300_ALPHA_TEST_OP_MASK (7 << 8)
1282# define R300_ALPHA_TEST_ENABLE (1 << 11)
1283
1284/* gap */
1285
1286/* Fragment program parameters in 7.16 floating point */
1287#define R300_PFS_PARAM_0_X 0x4C00
1288#define R300_PFS_PARAM_0_Y 0x4C04
1289#define R300_PFS_PARAM_0_Z 0x4C08
1290#define R300_PFS_PARAM_0_W 0x4C0C
1291/* GUESS: PARAM_31 is last, based on native limits reported by fglrx */
1292#define R300_PFS_PARAM_31_X 0x4DF0
1293#define R300_PFS_PARAM_31_Y 0x4DF4
1294#define R300_PFS_PARAM_31_Z 0x4DF8
1295#define R300_PFS_PARAM_31_W 0x4DFC
1296
1297/* Notes:
1298 * - AFAIK fglrx always sets BLEND_UNKNOWN when blending is used in
1299 * the application
1300 * - AFAIK fglrx always sets BLEND_NO_SEPARATE when CBLEND and ABLEND
1301 * are set to the same
1302 * function (both registers are always set up completely in any case)
1303 * - Most blend flags are simply copied from R200 and not tested yet
1304 */
1305#define R300_RB3D_CBLEND 0x4E04
1306#define R300_RB3D_ABLEND 0x4E08
1307/* the following only appear in CBLEND */
1308# define R300_BLEND_ENABLE (1 << 0)
1309# define R300_BLEND_UNKNOWN (3 << 1)
1310# define R300_BLEND_NO_SEPARATE (1 << 3)
1311/* the following are shared between CBLEND and ABLEND */
1312# define R300_FCN_MASK (3 << 12)
1313# define R300_COMB_FCN_ADD_CLAMP (0 << 12)
1314# define R300_COMB_FCN_ADD_NOCLAMP (1 << 12)
1315# define R300_COMB_FCN_SUB_CLAMP (2 << 12)
1316# define R300_COMB_FCN_SUB_NOCLAMP (3 << 12)
1317# define R300_COMB_FCN_MIN (4 << 12)
1318# define R300_COMB_FCN_MAX (5 << 12)
1319# define R300_COMB_FCN_RSUB_CLAMP (6 << 12)
1320# define R300_COMB_FCN_RSUB_NOCLAMP (7 << 12)
1321# define R300_BLEND_GL_ZERO (32)
1322# define R300_BLEND_GL_ONE (33)
1323# define R300_BLEND_GL_SRC_COLOR (34)
1324# define R300_BLEND_GL_ONE_MINUS_SRC_COLOR (35)
1325# define R300_BLEND_GL_DST_COLOR (36)
1326# define R300_BLEND_GL_ONE_MINUS_DST_COLOR (37)
1327# define R300_BLEND_GL_SRC_ALPHA (38)
1328# define R300_BLEND_GL_ONE_MINUS_SRC_ALPHA (39)
1329# define R300_BLEND_GL_DST_ALPHA (40)
1330# define R300_BLEND_GL_ONE_MINUS_DST_ALPHA (41)
1331# define R300_BLEND_GL_SRC_ALPHA_SATURATE (42)
1332# define R300_BLEND_GL_CONST_COLOR (43)
1333# define R300_BLEND_GL_ONE_MINUS_CONST_COLOR (44)
1334# define R300_BLEND_GL_CONST_ALPHA (45)
1335# define R300_BLEND_GL_ONE_MINUS_CONST_ALPHA (46)
1336# define R300_BLEND_MASK (63)
1337# define R300_SRC_BLEND_SHIFT (16)
1338# define R300_DST_BLEND_SHIFT (24)
1339#define R300_RB3D_BLEND_COLOR 0x4E10
1340#define R300_RB3D_COLORMASK 0x4E0C
1341# define R300_COLORMASK0_B (1<<0)
1342# define R300_COLORMASK0_G (1<<1)
1343# define R300_COLORMASK0_R (1<<2)
1344# define R300_COLORMASK0_A (1<<3)
1345
1346/* gap */
1347
1348#define R300_RB3D_COLOROFFSET0 0x4E28
1349# define R300_COLOROFFSET_MASK 0xFFFFFFF0 /* GUESS */
1350#define R300_RB3D_COLOROFFSET1 0x4E2C /* GUESS */
1351#define R300_RB3D_COLOROFFSET2 0x4E30 /* GUESS */
1352#define R300_RB3D_COLOROFFSET3 0x4E34 /* GUESS */
1353
1354/* gap */
1355
1356/* Bit 16: Larger tiles
1357 * Bit 17: 4x2 tiles
1358 * Bit 18: Extremely weird tile like, but some pixels duplicated?
1359 */
1360#define R300_RB3D_COLORPITCH0 0x4E38
1361# define R300_COLORPITCH_MASK 0x00001FF8 /* GUESS */
1362# define R300_COLOR_TILE_ENABLE (1 << 16) /* GUESS */
1363# define R300_COLOR_MICROTILE_ENABLE (1 << 17) /* GUESS */
1364# define R300_COLOR_MICROTILE_SQUARE_ENABLE (2 << 17)
1365# define R300_COLOR_ENDIAN_NO_SWAP (0 << 18) /* GUESS */
1366# define R300_COLOR_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */
1367# define R300_COLOR_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */
1368# define R300_COLOR_FORMAT_RGB565 (2 << 22)
1369# define R300_COLOR_FORMAT_ARGB8888 (3 << 22)
1370#define R300_RB3D_COLORPITCH1 0x4E3C /* GUESS */
1371#define R300_RB3D_COLORPITCH2 0x4E40 /* GUESS */
1372#define R300_RB3D_COLORPITCH3 0x4E44 /* GUESS */
1373
1374#define R300_RB3D_AARESOLVE_OFFSET 0x4E80
1375#define R300_RB3D_AARESOLVE_PITCH 0x4E84
1376#define R300_RB3D_AARESOLVE_CTL 0x4E88
1377/* gap */
1378
1379/* Guess by Vladimir.
1380 * Set to 0A before 3D operations, set to 02 afterwards.
1381 */
1382/*#define R300_RB3D_DSTCACHE_CTLSTAT 0x4E4C*/
1383# define R300_RB3D_DSTCACHE_UNKNOWN_02 0x00000002
1384# define R300_RB3D_DSTCACHE_UNKNOWN_0A 0x0000000A
1385
1386/* gap */
1387/* There seems to be no "write only" setting, so use Z-test = ALWAYS
1388 * for this.
1389 * Bit (1<<8) is the "test" bit. so plain write is 6 - vd
1390 */
1391#define R300_ZB_CNTL 0x4F00
1392# define R300_STENCIL_ENABLE (1 << 0)
1393# define R300_Z_ENABLE (1 << 1)
1394# define R300_Z_WRITE_ENABLE (1 << 2)
1395# define R300_Z_SIGNED_COMPARE (1 << 3)
1396# define R300_STENCIL_FRONT_BACK (1 << 4)
1397
1398#define R300_ZB_ZSTENCILCNTL 0x4f04
1399 /* functions */
1400# define R300_ZS_NEVER 0
1401# define R300_ZS_LESS 1
1402# define R300_ZS_LEQUAL 2
1403# define R300_ZS_EQUAL 3
1404# define R300_ZS_GEQUAL 4
1405# define R300_ZS_GREATER 5
1406# define R300_ZS_NOTEQUAL 6
1407# define R300_ZS_ALWAYS 7
1408# define R300_ZS_MASK 7
1409 /* operations */
1410# define R300_ZS_KEEP 0
1411# define R300_ZS_ZERO 1
1412# define R300_ZS_REPLACE 2
1413# define R300_ZS_INCR 3
1414# define R300_ZS_DECR 4
1415# define R300_ZS_INVERT 5
1416# define R300_ZS_INCR_WRAP 6
1417# define R300_ZS_DECR_WRAP 7
1418# define R300_Z_FUNC_SHIFT 0
1419 /* front and back refer to operations done for front
1420 and back faces, i.e. separate stencil function support */
1421# define R300_S_FRONT_FUNC_SHIFT 3
1422# define R300_S_FRONT_SFAIL_OP_SHIFT 6
1423# define R300_S_FRONT_ZPASS_OP_SHIFT 9
1424# define R300_S_FRONT_ZFAIL_OP_SHIFT 12
1425# define R300_S_BACK_FUNC_SHIFT 15
1426# define R300_S_BACK_SFAIL_OP_SHIFT 18
1427# define R300_S_BACK_ZPASS_OP_SHIFT 21
1428# define R300_S_BACK_ZFAIL_OP_SHIFT 24
1429
1430#define R300_ZB_STENCILREFMASK 0x4f08
1431# define R300_STENCILREF_SHIFT 0
1432# define R300_STENCILREF_MASK 0x000000ff
1433# define R300_STENCILMASK_SHIFT 8
1434# define R300_STENCILMASK_MASK 0x0000ff00
1435# define R300_STENCILWRITEMASK_SHIFT 16
1436# define R300_STENCILWRITEMASK_MASK 0x00ff0000
1437
1438/* gap */
1439
1440#define R300_ZB_FORMAT 0x4f10
1441# define R300_DEPTHFORMAT_16BIT_INT_Z (0 << 0)
1442# define R300_DEPTHFORMAT_16BIT_13E3 (1 << 0)
1443# define R300_DEPTHFORMAT_24BIT_INT_Z_8BIT_STENCIL (2 << 0)
1444/* reserved up to (15 << 0) */
1445# define R300_INVERT_13E3_LEADING_ONES (0 << 4)
1446# define R300_INVERT_13E3_LEADING_ZEROS (1 << 4)
1447
1448#define R300_ZB_ZTOP 0x4F14
1449# define R300_ZTOP_DISABLE (0 << 0)
1450# define R300_ZTOP_ENABLE (1 << 0)
1451
1452/* gap */
1453
1454#define R300_ZB_ZCACHE_CTLSTAT 0x4f18
1455# define R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_NO_EFFECT (0 << 0)
1456# define R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_FLUSH_AND_FREE (1 << 0)
1457# define R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_NO_EFFECT (0 << 1)
1458# define R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_FREE (1 << 1)
1459# define R300_ZB_ZCACHE_CTLSTAT_ZC_BUSY_IDLE (0 << 31)
1460# define R300_ZB_ZCACHE_CTLSTAT_ZC_BUSY_BUSY (1 << 31)
1461
1462#define R300_ZB_BW_CNTL 0x4f1c
1463# define R300_HIZ_DISABLE (0 << 0)
1464# define R300_HIZ_ENABLE (1 << 0)
1465# define R300_HIZ_MIN (0 << 1)
1466# define R300_HIZ_MAX (1 << 1)
1467# define R300_FAST_FILL_DISABLE (0 << 2)
1468# define R300_FAST_FILL_ENABLE (1 << 2)
1469# define R300_RD_COMP_DISABLE (0 << 3)
1470# define R300_RD_COMP_ENABLE (1 << 3)
1471# define R300_WR_COMP_DISABLE (0 << 4)
1472# define R300_WR_COMP_ENABLE (1 << 4)
1473# define R300_ZB_CB_CLEAR_RMW (0 << 5)
1474# define R300_ZB_CB_CLEAR_CACHE_LINEAR (1 << 5)
1475# define R300_FORCE_COMPRESSED_STENCIL_VALUE_DISABLE (0 << 6)
1476# define R300_FORCE_COMPRESSED_STENCIL_VALUE_ENABLE (1 << 6)
1477
1478# define R500_ZEQUAL_OPTIMIZE_ENABLE (0 << 7)
1479# define R500_ZEQUAL_OPTIMIZE_DISABLE (1 << 7)
1480# define R500_SEQUAL_OPTIMIZE_ENABLE (0 << 8)
1481# define R500_SEQUAL_OPTIMIZE_DISABLE (1 << 8)
1482
1483# define R500_BMASK_ENABLE (0 << 10)
1484# define R500_BMASK_DISABLE (1 << 10)
1485# define R500_HIZ_EQUAL_REJECT_DISABLE (0 << 11)
1486# define R500_HIZ_EQUAL_REJECT_ENABLE (1 << 11)
1487# define R500_HIZ_FP_EXP_BITS_DISABLE (0 << 12)
1488# define R500_HIZ_FP_EXP_BITS_1 (1 << 12)
1489# define R500_HIZ_FP_EXP_BITS_2 (2 << 12)
1490# define R500_HIZ_FP_EXP_BITS_3 (3 << 12)
1491# define R500_HIZ_FP_EXP_BITS_4 (4 << 12)
1492# define R500_HIZ_FP_EXP_BITS_5 (5 << 12)
1493# define R500_HIZ_FP_INVERT_LEADING_ONES (0 << 15)
1494# define R500_HIZ_FP_INVERT_LEADING_ZEROS (1 << 15)
1495# define R500_TILE_OVERWRITE_RECOMPRESSION_ENABLE (0 << 16)
1496# define R500_TILE_OVERWRITE_RECOMPRESSION_DISABLE (1 << 16)
1497# define R500_CONTIGUOUS_6XAA_SAMPLES_ENABLE (0 << 17)
1498# define R500_CONTIGUOUS_6XAA_SAMPLES_DISABLE (1 << 17)
1499# define R500_PEQ_PACKING_DISABLE (0 << 18)
1500# define R500_PEQ_PACKING_ENABLE (1 << 18)
1501# define R500_COVERED_PTR_MASKING_DISABLE (0 << 18)
1502# define R500_COVERED_PTR_MASKING_ENABLE (1 << 18)
1503
1504
1505/* gap */
1506
1507/* Z Buffer Address Offset.
1508 * Bits 31 to 5 are used for aligned Z buffer address offset for macro tiles.
1509 */
1510#define R300_ZB_DEPTHOFFSET 0x4f20
1511
1512/* Z Buffer Pitch and Endian Control */
1513#define R300_ZB_DEPTHPITCH 0x4f24
1514# define R300_DEPTHPITCH_MASK 0x00003FFC
1515# define R300_DEPTHMACROTILE_DISABLE (0 << 16)
1516# define R300_DEPTHMACROTILE_ENABLE (1 << 16)
1517# define R300_DEPTHMICROTILE_LINEAR (0 << 17)
1518# define R300_DEPTHMICROTILE_TILED (1 << 17)
1519# define R300_DEPTHMICROTILE_TILED_SQUARE (2 << 17)
1520# define R300_DEPTHENDIAN_NO_SWAP (0 << 18)
1521# define R300_DEPTHENDIAN_WORD_SWAP (1 << 18)
1522# define R300_DEPTHENDIAN_DWORD_SWAP (2 << 18)
1523# define R300_DEPTHENDIAN_HALF_DWORD_SWAP (3 << 18)
1524
1525/* Z Buffer Clear Value */
1526#define R300_ZB_DEPTHCLEARVALUE 0x4f28
1527
1528#define R300_ZB_ZMASK_OFFSET 0x4f30
1529#define R300_ZB_ZMASK_PITCH 0x4f34
1530#define R300_ZB_ZMASK_WRINDEX 0x4f38
1531#define R300_ZB_ZMASK_DWORD 0x4f3c
1532#define R300_ZB_ZMASK_RDINDEX 0x4f40
1533
1534/* Hierarchical Z Memory Offset */
1535#define R300_ZB_HIZ_OFFSET 0x4f44
1536
1537/* Hierarchical Z Write Index */
1538#define R300_ZB_HIZ_WRINDEX 0x4f48
1539
1540/* Hierarchical Z Data */
1541#define R300_ZB_HIZ_DWORD 0x4f4c
1542
1543/* Hierarchical Z Read Index */
1544#define R300_ZB_HIZ_RDINDEX 0x4f50
1545
1546/* Hierarchical Z Pitch */
1547#define R300_ZB_HIZ_PITCH 0x4f54
1548
1549/* Z Buffer Z Pass Counter Data */
1550#define R300_ZB_ZPASS_DATA 0x4f58
1551
1552/* Z Buffer Z Pass Counter Address */
1553#define R300_ZB_ZPASS_ADDR 0x4f5c
1554
1555/* Depth buffer X and Y coordinate offset */
1556#define R300_ZB_DEPTHXY_OFFSET 0x4f60
1557# define R300_DEPTHX_OFFSET_SHIFT 1
1558# define R300_DEPTHX_OFFSET_MASK 0x000007FE
1559# define R300_DEPTHY_OFFSET_SHIFT 17
1560# define R300_DEPTHY_OFFSET_MASK 0x07FE0000
1561
1562/* Sets the fifo sizes */
1563#define R500_ZB_FIFO_SIZE 0x4fd0
1564# define R500_OP_FIFO_SIZE_FULL (0 << 0)
1565# define R500_OP_FIFO_SIZE_HALF (1 << 0)
1566# define R500_OP_FIFO_SIZE_QUATER (2 << 0)
1567# define R500_OP_FIFO_SIZE_EIGTHS (4 << 0)
1568
1569/* Stencil Reference Value and Mask for backfacing quads */
1570/* R300_ZB_STENCILREFMASK handles front face */
1571#define R500_ZB_STENCILREFMASK_BF 0x4fd4
1572# define R500_STENCILREF_SHIFT 0
1573# define R500_STENCILREF_MASK 0x000000ff
1574# define R500_STENCILMASK_SHIFT 8
1575# define R500_STENCILMASK_MASK 0x0000ff00
1576# define R500_STENCILWRITEMASK_SHIFT 16
1577# define R500_STENCILWRITEMASK_MASK 0x00ff0000
1578
1579/* BEGIN: Vertex program instruction set */
1580
1581/* Every instruction is four dwords long:
1582 * DWORD 0: output and opcode
1583 * DWORD 1: first argument
1584 * DWORD 2: second argument
1585 * DWORD 3: third argument
1586 *
1587 * Notes:
1588 * - ABS r, a is implemented as MAX r, a, -a
1589 * - MOV is implemented as ADD to zero
1590 * - XPD is implemented as MUL + MAD
1591 * - FLR is implemented as FRC + ADD
1592 * - apparently, fglrx tries to schedule instructions so that there is at
1593 * least one instruction between the write to a temporary and the first
1594 * read from said temporary; however, violations of this scheduling are
1595 * allowed
1596 * - register indices seem to be unrelated with OpenGL aliasing to
1597 * conventional state
1598 * - only one attribute and one parameter can be loaded at a time; however,
1599 * the same attribute/parameter can be used for more than one argument
1600 * - the second software argument for POW is the third hardware argument
1601 * (no idea why)
1602 * - MAD with only temporaries as input seems to use VPI_OUT_SELECT_MAD_2
1603 *
1604 * There is some magic surrounding LIT:
1605 * The single argument is replicated across all three inputs, but swizzled:
1606 * First argument: xyzy
1607 * Second argument: xyzx
1608 * Third argument: xyzw
1609 * Whenever the result is used later in the fragment program, fglrx forces
1610 * x and w to be 1.0 in the input selection; I don't know whether this is
1611 * strictly necessary
1612 */
1613#define R300_VPI_OUT_OP_DOT (1 << 0)
1614#define R300_VPI_OUT_OP_MUL (2 << 0)
1615#define R300_VPI_OUT_OP_ADD (3 << 0)
1616#define R300_VPI_OUT_OP_MAD (4 << 0)
1617#define R300_VPI_OUT_OP_DST (5 << 0)
1618#define R300_VPI_OUT_OP_FRC (6 << 0)
1619#define R300_VPI_OUT_OP_MAX (7 << 0)
1620#define R300_VPI_OUT_OP_MIN (8 << 0)
1621#define R300_VPI_OUT_OP_SGE (9 << 0)
1622#define R300_VPI_OUT_OP_SLT (10 << 0)
1623 /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, vector(scalar, vector) */
1624#define R300_VPI_OUT_OP_UNK12 (12 << 0)
1625#define R300_VPI_OUT_OP_ARL (13 << 0)
1626#define R300_VPI_OUT_OP_EXP (65 << 0)
1627#define R300_VPI_OUT_OP_LOG (66 << 0)
1628 /* Used in fog computations, scalar(scalar) */
1629#define R300_VPI_OUT_OP_UNK67 (67 << 0)
1630#define R300_VPI_OUT_OP_LIT (68 << 0)
1631#define R300_VPI_OUT_OP_POW (69 << 0)
1632#define R300_VPI_OUT_OP_RCP (70 << 0)
1633#define R300_VPI_OUT_OP_RSQ (72 << 0)
1634 /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, scalar(scalar) */
1635#define R300_VPI_OUT_OP_UNK73 (73 << 0)
1636#define R300_VPI_OUT_OP_EX2 (75 << 0)
1637#define R300_VPI_OUT_OP_LG2 (76 << 0)
1638#define R300_VPI_OUT_OP_MAD_2 (128 << 0)
1639 /* all temps, vector(scalar, vector, vector) */
1640#define R300_VPI_OUT_OP_UNK129 (129 << 0)
1641
1642#define R300_VPI_OUT_REG_CLASS_TEMPORARY (0 << 8)
1643#define R300_VPI_OUT_REG_CLASS_ADDR (1 << 8)
1644#define R300_VPI_OUT_REG_CLASS_RESULT (2 << 8)
1645#define R300_VPI_OUT_REG_CLASS_MASK (31 << 8)
1646
1647#define R300_VPI_OUT_REG_INDEX_SHIFT 13
1648 /* GUESS based on fglrx native limits */
1649#define R300_VPI_OUT_REG_INDEX_MASK (31 << 13)
1650
1651#define R300_VPI_OUT_WRITE_X (1 << 20)
1652#define R300_VPI_OUT_WRITE_Y (1 << 21)
1653#define R300_VPI_OUT_WRITE_Z (1 << 22)
1654#define R300_VPI_OUT_WRITE_W (1 << 23)
1655
1656#define R300_VPI_IN_REG_CLASS_TEMPORARY (0 << 0)
1657#define R300_VPI_IN_REG_CLASS_ATTRIBUTE (1 << 0)
1658#define R300_VPI_IN_REG_CLASS_PARAMETER (2 << 0)
1659#define R300_VPI_IN_REG_CLASS_NONE (9 << 0)
1660#define R300_VPI_IN_REG_CLASS_MASK (31 << 0)
1661
1662#define R300_VPI_IN_REG_INDEX_SHIFT 5
1663 /* GUESS based on fglrx native limits */
1664#define R300_VPI_IN_REG_INDEX_MASK (255 << 5)
1665
1666/* The R300 can select components from the input register arbitrarily.
1667 * Use the following constants, shifted by the component shift you
1668 * want to select
1669 */
1670#define R300_VPI_IN_SELECT_X 0
1671#define R300_VPI_IN_SELECT_Y 1
1672#define R300_VPI_IN_SELECT_Z 2
1673#define R300_VPI_IN_SELECT_W 3
1674#define R300_VPI_IN_SELECT_ZERO 4
1675#define R300_VPI_IN_SELECT_ONE 5
1676#define R300_VPI_IN_SELECT_MASK 7
1677
1678#define R300_VPI_IN_X_SHIFT 13
1679#define R300_VPI_IN_Y_SHIFT 16
1680#define R300_VPI_IN_Z_SHIFT 19
1681#define R300_VPI_IN_W_SHIFT 22
1682
1683#define R300_VPI_IN_NEG_X (1 << 25)
1684#define R300_VPI_IN_NEG_Y (1 << 26)
1685#define R300_VPI_IN_NEG_Z (1 << 27)
1686#define R300_VPI_IN_NEG_W (1 << 28)
1687/* END: Vertex program instruction set */
1688
1689/* BEGIN: Packet 3 commands */
1690
1691/* A primitive emission dword. */
1692#define R300_PRIM_TYPE_NONE (0 << 0)
1693#define R300_PRIM_TYPE_POINT (1 << 0)
1694#define R300_PRIM_TYPE_LINE (2 << 0)
1695#define R300_PRIM_TYPE_LINE_STRIP (3 << 0)
1696#define R300_PRIM_TYPE_TRI_LIST (4 << 0)
1697#define R300_PRIM_TYPE_TRI_FAN (5 << 0)
1698#define R300_PRIM_TYPE_TRI_STRIP (6 << 0)
1699#define R300_PRIM_TYPE_TRI_TYPE2 (7 << 0)
1700#define R300_PRIM_TYPE_RECT_LIST (8 << 0)
1701#define R300_PRIM_TYPE_3VRT_POINT_LIST (9 << 0)
1702#define R300_PRIM_TYPE_3VRT_LINE_LIST (10 << 0)
1703 /* GUESS (based on r200) */
1704#define R300_PRIM_TYPE_POINT_SPRITES (11 << 0)
1705#define R300_PRIM_TYPE_LINE_LOOP (12 << 0)
1706#define R300_PRIM_TYPE_QUADS (13 << 0)
1707#define R300_PRIM_TYPE_QUAD_STRIP (14 << 0)
1708#define R300_PRIM_TYPE_POLYGON (15 << 0)
1709#define R300_PRIM_TYPE_MASK 0xF
1710#define R300_PRIM_WALK_IND (1 << 4)
1711#define R300_PRIM_WALK_LIST (2 << 4)
1712#define R300_PRIM_WALK_RING (3 << 4)
1713#define R300_PRIM_WALK_MASK (3 << 4)
1714 /* GUESS (based on r200) */
1715#define R300_PRIM_COLOR_ORDER_BGRA (0 << 6)
1716#define R300_PRIM_COLOR_ORDER_RGBA (1 << 6)
1717#define R300_PRIM_NUM_VERTICES_SHIFT 16
1718#define R300_PRIM_NUM_VERTICES_MASK 0xffff
1719
1720/* Draw a primitive from vertex data in arrays loaded via 3D_LOAD_VBPNTR.
1721 * Two parameter dwords:
1722 * 0. The first parameter appears to be always 0
1723 * 1. The second parameter is a standard primitive emission dword.
1724 */
1725#define R300_PACKET3_3D_DRAW_VBUF 0x00002800
1726
1727/* Specify the full set of vertex arrays as (address, stride).
1728 * The first parameter is the number of vertex arrays specified.
1729 * The rest of the command is a variable length list of blocks, where
1730 * each block is three dwords long and specifies two arrays.
1731 * The first dword of a block is split into two words, the lower significant
1732 * word refers to the first array, the more significant word to the second
1733 * array in the block.
1734 * The low byte of each word contains the size of an array entry in dwords,
1735 * the high byte contains the stride of the array.
1736 * The second dword of a block contains the pointer to the first array,
1737 * the third dword of a block contains the pointer to the second array.
1738 * Note that if the total number of arrays is odd, the third dword of
1739 * the last block is omitted.
1740 */
1741#define R300_PACKET3_3D_LOAD_VBPNTR 0x00002F00
1742
1743#define R300_PACKET3_INDX_BUFFER 0x00003300
1744# define R300_EB_UNK1_SHIFT 24
1745# define R300_EB_UNK1 (0x80<<24)
1746# define R300_EB_UNK2 0x0810
1747#define R300_PACKET3_3D_DRAW_VBUF_2 0x00003400
1748#define R300_PACKET3_3D_DRAW_INDX_2 0x00003600
1749
1750/* END: Packet 3 commands */
1751
1752
1753/* Color formats for 2d packets
1754 */
1755#define R300_CP_COLOR_FORMAT_CI8 2
1756#define R300_CP_COLOR_FORMAT_ARGB1555 3
1757#define R300_CP_COLOR_FORMAT_RGB565 4
1758#define R300_CP_COLOR_FORMAT_ARGB8888 6
1759#define R300_CP_COLOR_FORMAT_RGB332 7
1760#define R300_CP_COLOR_FORMAT_RGB8 9
1761#define R300_CP_COLOR_FORMAT_ARGB4444 15
1762
1763/*
1764 * CP type-3 packets
1765 */
1766#define R300_CP_CMD_BITBLT_MULTI 0xC0009B00
1767
1768#define R500_VAP_INDEX_OFFSET 0x208c
1769
1770#define R500_GA_US_VECTOR_INDEX 0x4250
1771#define R500_GA_US_VECTOR_DATA 0x4254
1772
1773#define R500_RS_IP_0 0x4074
1774#define R500_RS_INST_0 0x4320
1775
1776#define R500_US_CONFIG 0x4600
1777
1778#define R500_US_FC_CTRL 0x4624
1779#define R500_US_CODE_ADDR 0x4630
1780
1781#define R500_RB3D_COLOR_CLEAR_VALUE_AR 0x46c0
1782#define R500_RB3D_CONSTANT_COLOR_AR 0x4ef8
1783
1784#define R300_SU_REG_DEST 0x42c8
1785#define RV530_FG_ZBREG_DEST 0x4be8
1786#define R300_ZB_ZPASS_DATA 0x4f58
1787#define R300_ZB_ZPASS_ADDR 0x4f5c
1788
1789#endif /* _R300_REG_H */
1790

source code of linux/drivers/gpu/drm/radeon/r300_reg.h