1/* SPDX-License-Identifier: GPL-2.0 */
2/***************************************************************************
3 * *
4 * Copyright (c) 2000-2008 LSI Corporation. All rights reserved. *
5 * *
6 * Description *
7 * ------------ *
8 * This include file contains SAS firmware interface IOC Log Info codes *
9 * *
10 *-------------------------------------------------------------------------*
11 */
12
13#ifndef IOPI_IOCLOGINFO_H_INCLUDED
14#define IOPI_IOCLOGINFO_H_INCLUDED
15
16#define SAS_LOGINFO_NEXUS_LOSS 0x31170000
17#define SAS_LOGINFO_MASK 0xFFFF0000
18
19/****************************************************************************/
20/* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */
21/* Format: */
22/* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) */
23/* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR */
24/* Bits 23-16: LOGINFO_CODE */
25/* Bits 15-0: LOGINFO_CODE Specific */
26/****************************************************************************/
27
28/****************************************************************************/
29/* IOC_LOGINFO_ORIGINATOR defines */
30/****************************************************************************/
31#define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000)
32#define IOC_LOGINFO_ORIGINATOR_PL (0x01000000)
33#define IOC_LOGINFO_ORIGINATOR_IR (0x02000000)
34
35#define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000)
36
37/****************************************************************************/
38/* LOGINFO_CODE defines */
39/****************************************************************************/
40#define IOC_LOGINFO_CODE_MASK (0x00FF0000)
41#define IOC_LOGINFO_CODE_SHIFT (16)
42
43/****************************************************************************/
44/* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP */
45/****************************************************************************/
46#define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000)
47#define IOP_LOGINFO_CODE_UNUSED2 (0x00020000)
48#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000)
49#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */
50#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */
51#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */
52#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */
53#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */
54#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */
55#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */
56
57#define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE (0x0003E000) /* Tried to upload from flash, but there is none */
58#define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE (0x0003E001) /* ImageType field contents were invalid */
59#define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */
60#define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occurred while attempting to upload the entire flash */
61#define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occurred while attempting to upload single flash region */
62#define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occurred while DMAing FW to host memory */
63
64#define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */
65
66#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000)
67
68#define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */
69#define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */
70
71#define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001)
72#define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002)
73#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003)
74#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004)
75#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005)
76
77#define IOP_LOGINFO_CODE_LOG_TIMESTAMP_EVENT (0x00080000)
78
79/****************************************************************************/
80/* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */
81/****************************************************************************/
82#define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000) /* see SUB_CODE_OPEN_FAIL_ below */
83
84#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_NO_DEST_TIME_OUT (0x00000001)
85#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATHWAY_BLOCKED (0x00000002)
86#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE0 (0x00000003)
87#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE1 (0x00000004)
88#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE0 (0x00000005)
89#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE1 (0x00000006)
90#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP0 (0x00000007)
91#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP1 (0x00000008)
92#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RETRY (0x00000009)
93#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BREAK (0x0000000A)
94#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0B (0x0000000B)
95#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP (0x0000000C)
96#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D (0x0000000D)
97#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL (0x0000000E)
98#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BAD_DEST (0x00000011)
99#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP (0x00000012)
100#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP (0x00000013)
101#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0 (0x00000014)
102#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON1 (0x00000015)
103#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON2 (0x00000016)
104#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON3 (0x00000017)
105#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_STP_RESOURCES_BSY (0x00000018)
106#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_WRONG_DESTINATION (0x00000019)
107
108#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATH_BLOCKED (0x0000001B) /* Retry Timeout */
109#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_AWT_MAXED (0x0000001C) /* Retry Timeout */
110
111
112
113#define PL_LOGINFO_CODE_INVALID_SGL (0x00020000)
114#define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000)
115#define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000)
116#define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000)
117#define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000)
118#define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000)
119#define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000)
120#define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000)
121#define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000)
122#define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000)
123#define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000)
124#define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000)
125#define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000)
126#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000)
127#define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */
128#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */
129#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */
130#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */
131#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */
132#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */
133#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */
134#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */
135#define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000)
136#define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE) */
137#define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE)*/
138#define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000)
139#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000)
140#define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000)
141#define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000)
142#define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000)
143#define PL_LOGINFO_CODE_IO_CANCELLED_DUE_TO_R_ERR (0x00180000)
144#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100)
145#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101)
146#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_SATA_NEG_RATE_2HI (0x00000102)
147#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_RATE_NOT_SUPPORTED (0x00000103)
148#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_BREAK (0x00000104)
149#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ZONE_VIOLATION (0x00000114)
150#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON0 (0x00000114) /* Open Reject (Zone Violation) - available on SAS-2 devices */
151#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON1 (0x00000115)
152#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON2 (0x00000116)
153#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON3 (0x00000117)
154#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */
155#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATH_BLOCKED (0x0000011B)
156#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */
157
158#define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120)
159#define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */
160#define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */
161
162
163#define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200)
164#define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300)
165#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400)
166/* Bits 0-3 encode Transport Status Register (offset 0x08) */
167/* Bit 0 is Status Bit 0: FrameXferErr */
168/* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */
169/* Bit 3 is Status Bit 18 WriteDataLenghtGTDataLengthErr */
170
171#define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500)
172#define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600)
173#define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700)
174#define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800)
175#define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900)
176#define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00)
177#define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00)
178#define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00)
179#define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00)
180#define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00)
181#define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01)
182#define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00)
183#define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000)
184#define PL_LOGINFO_SUB_CODE_BREAK_ON_SATA_CONNECTION (0x00002000)
185/* not currently used in mainline */
186#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK (0x00003000)
187#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK_AIP (0x00004000)
188#define PL_LOGINFO_SUB_CODE_BREAK_ON_INCOMPLETE_BREAK_RCVD (0x00005000)
189
190#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */
191#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occurred on SMP Read */
192#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occurred on SMP Write */
193#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */
194#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */
195#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */
196#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */
197#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */
198#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */
199#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */
200#define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */
201#define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */
202#define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */
203#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */
204
205#define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */
206#define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */
207#define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */
208#define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */
209#define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */
210#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */
211#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transferring data */
212#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transferring sense data */
213#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */
214#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */
215#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */
216#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/
217#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode f/w location 1 */
218#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_2 (0x0020010D) /* SEP doesn't support CDB opcode f/w location 2 */
219#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_3 (0x0020010E) /* SEP doesn't support CDB opcode f/w location 3 */
220
221
222/****************************************************************************/
223/* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */
224/****************************************************************************/
225#define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000)
226#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)
227
228/* Amount of information passed down for Create Volume is too large */
229#define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001)
230/* Creation of duplicate volume attempted (Bus/Target ID checked) */
231#define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002)
232/* Creation failed due to maximum number of supported volumes exceeded */
233#define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003)
234/* Creation failed due to DMA error in trying to read from host */
235#define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004)
236/* Creation failed due to invalid volume type passed down */
237#define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005)
238/* Creation failed due to error reading MFG Page 4 */
239#define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006)
240/* Creation failed when trying to create internal structures */
241#define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007)
242
243/* Activation failed due to trying to activate an already active volume */
244#define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010)
245/* Activation failed due to trying to active unsupported volume type */
246#define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011)
247/* Activation failed due to trying to active too many volumes */
248#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012)
249/* Activation failed due to Volume ID in use already */
250#define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013)
251/* Activation failed call to activateVolume returned failure */
252#define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014)
253/* Activation failed trying to import the volume */
254#define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015)
255/* Activation failed trying to import the volume */
256#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_PHYS_DISKS (0x00010016)
257
258/* Phys Disk failed, too many phys disks */
259#define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020)
260/* Amount of information passed down for Create Pnysdisk is too large */
261#define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021)
262/* Creation failed due to DMA error in trying to read from host */
263#define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022)
264/* Creation failed due to invalid Bus TargetID passed down */
265#define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023)
266/* Creation failed due to error in creating RAID Phys Disk Config Page */
267#define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024)
268
269
270/* Compatibility Error : IR Disabled */
271#define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030)
272/* Compatibility Error : Inquiry Command failed */
273#define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031)
274/* Compatibility Error : Device not direct access device */
275#define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032)
276/* Compatibility Error : Removable device found */
277#define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033)
278/* Compatibility Error : Device SCSI Version not 2 or higher */
279#define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034)
280/* Compatibility Error : SATA device, 48 BIT LBA not supported */
281#define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035)
282/* Compatibility Error : Device does not have 512 byte block sizes */
283#define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036)
284/* Compatibility Error : Volume Type check failed */
285#define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037)
286/* Compatibility Error : Volume Type is unsupported by FW */
287#define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038)
288/* Compatibility Error : Disk drive too small for use in volume */
289#define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039)
290/* Compatibility Error : Phys disk for Create Volume not found */
291#define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A)
292/* Compatibility Error : membership count error, too many or too few disks for volume type */
293#define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B)
294/* Compatibility Error : Disk stripe sizes must be 64KB */
295#define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C)
296/* Compatibility Error : IME size limited to < 2TB */
297#define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D)
298
299/* Device Firmware Update: DFU can only be started once */
300#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DFU_IN_PROGRESS (0x00010050)
301/* Device Firmware Update: Volume must be Optimal/Active/non-Quiesced */
302#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DEVICE_IN_INVALID_STATE (0x00010051)
303/* Device Firmware Update: DFU Timeout cannot be zero */
304#define IR_LOGINFO_DEV_FW_UPDATE_ERR_INVALID_TIMEOUT (0x00010052)
305/* Device Firmware Update: CREATE TIMER FAILED */
306#define IR_LOGINFO_DEV_FW_UPDATE_ERR_NO_TIMERS (0x00010053)
307/* Device Firmware Update: Failed to read SAS_IO_UNIT_PG_1 */
308#define IR_LOGINFO_DEV_FW_UPDATE_ERR_READING_CFG_PAGE (0x00010054)
309/* Device Firmware Update: Invalid SAS_IO_UNIT_PG_1 value(s) */
310#define IR_LOGINFO_DEV_FW_UPDATE_ERR_PORT_IO_TIMEOUTS_REQUIRED (0x00010055)
311/* Device Firmware Update: Unable to allocate memory for page */
312#define IR_LOGINFO_DEV_FW_UPDATE_ERR_ALLOC_CFG_PAGE (0x00010056)
313
314
315/****************************************************************************/
316/* Defines for convenience */
317/****************************************************************************/
318#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP)
319#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL)
320#define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR)
321
322#endif /* end of file */
323
324

Provided by KDAB

Privacy Policy
Improve your Profiling and Debugging skills
Find out more

source code of linux/drivers/message/fusion/lsi/mpi_log_sas.h