1/* SPDX-License-Identifier: GPL-2.0 */
2/* Copyright(c) 1999 - 2018 Intel Corporation. */
3
4#ifndef _E1000E_ICH8LAN_H_
5#define _E1000E_ICH8LAN_H_
6
7#define ICH_FLASH_GFPREG 0x0000
8#define ICH_FLASH_HSFSTS 0x0004
9#define ICH_FLASH_HSFCTL 0x0006
10#define ICH_FLASH_FADDR 0x0008
11#define ICH_FLASH_FDATA0 0x0010
12#define ICH_FLASH_PR0 0x0074
13
14/* Requires up to 10 seconds when MNG might be accessing part. */
15#define ICH_FLASH_READ_COMMAND_TIMEOUT 10000000
16#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 10000000
17#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 10000000
18#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
19#define ICH_FLASH_CYCLE_REPEAT_COUNT 10
20
21#define ICH_CYCLE_READ 0
22#define ICH_CYCLE_WRITE 2
23#define ICH_CYCLE_ERASE 3
24
25#define FLASH_GFPREG_BASE_MASK 0x1FFF
26#define FLASH_SECTOR_ADDR_SHIFT 12
27
28#define ICH_FLASH_SEG_SIZE_256 256
29#define ICH_FLASH_SEG_SIZE_4K 4096
30#define ICH_FLASH_SEG_SIZE_8K 8192
31#define ICH_FLASH_SEG_SIZE_64K 65536
32
33#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */
34/* FW established a valid mode */
35#define E1000_ICH_FWSM_FW_VALID 0x00008000
36#define E1000_ICH_FWSM_PCIM2PCI 0x01000000 /* ME PCIm-to-PCI active */
37#define E1000_ICH_FWSM_PCIM2PCI_COUNT 2000
38
39#define E1000_ICH_MNG_IAMT_MODE 0x2
40
41#define E1000_FWSM_WLOCK_MAC_MASK 0x0380
42#define E1000_FWSM_WLOCK_MAC_SHIFT 7
43#define E1000_FWSM_ULP_CFG_DONE 0x00000400 /* Low power cfg done */
44#define E1000_EXFWSM_DPG_EXIT_DONE 0x00000001
45
46/* Shared Receive Address Registers */
47#define E1000_SHRAL_PCH_LPT(_i) (0x05408 + ((_i) * 8))
48#define E1000_SHRAH_PCH_LPT(_i) (0x0540C + ((_i) * 8))
49
50#define E1000_H2ME 0x05B50 /* Host to ME */
51#define E1000_H2ME_START_DPG 0x00000001 /* indicate the ME of DPG */
52#define E1000_H2ME_EXIT_DPG 0x00000002 /* indicate the ME exit DPG */
53#define E1000_H2ME_ULP 0x00000800 /* ULP Indication Bit */
54#define E1000_H2ME_ENFORCE_SETTINGS 0x00001000 /* Enforce Settings */
55
56#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
57 (ID_LED_OFF1_OFF2 << 8) | \
58 (ID_LED_OFF1_ON2 << 4) | \
59 (ID_LED_DEF1_DEF2))
60
61#define E1000_ICH_NVM_SIG_WORD 0x13u
62#define E1000_ICH_NVM_SIG_MASK 0xC000u
63#define E1000_ICH_NVM_VALID_SIG_MASK 0xC0u
64#define E1000_ICH_NVM_SIG_VALUE 0x80u
65
66#define E1000_ICH8_LAN_INIT_TIMEOUT 1500
67
68/* FEXT register bit definition */
69#define E1000_FEXT_PHY_CABLE_DISCONNECTED 0x00000004
70
71#define E1000_FEXTNVM_SW_CONFIG 1
72#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* different on ICH8M */
73
74#define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK 0x0C000000
75#define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC 0x08000000
76
77#define E1000_FEXTNVM4_BEACON_DURATION_MASK 0x7
78#define E1000_FEXTNVM4_BEACON_DURATION_8USEC 0x7
79#define E1000_FEXTNVM4_BEACON_DURATION_16USEC 0x3
80
81#define E1000_FEXTNVM6_REQ_PLL_CLK 0x00000100
82#define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION 0x00000200
83#define E1000_FEXTNVM6_K1_OFF_ENABLE 0x80000000
84/* bit for disabling packet buffer read */
85#define E1000_FEXTNVM7_DISABLE_PB_READ 0x00040000
86#define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004
87#define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020
88#define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS 0x00000800
89#define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS 0x00001000
90#define E1000_FEXTNVM11_DISABLE_PB_READ 0x00000200
91#define E1000_FEXTNVM11_DISABLE_MULR_FIX 0x00002000
92
93/* bit24: RXDCTL thresholds granularity: 0 - cache lines, 1 - descriptors */
94#define E1000_RXDCTL_THRESH_UNIT_DESC 0x01000000
95
96#define K1_ENTRY_LATENCY 0
97#define K1_MIN_TIME 1
98#define NVM_SIZE_MULTIPLIER 4096 /*multiplier for NVMS field */
99#define E1000_FLASH_BASE_ADDR 0xE000 /*offset of NVM access regs */
100#define E1000_CTRL_EXT_NVMVS 0x3 /*NVM valid sector */
101#define E1000_TARC0_CB_MULTIQ_3_REQ 0x30000000
102#define E1000_TARC0_CB_MULTIQ_2_REQ 0x20000000
103#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL
104
105#define E1000_ICH_RAR_ENTRIES 7
106#define E1000_PCH2_RAR_ENTRIES 5 /* RAR[0], SHRA[0-3] */
107#define E1000_PCH_LPT_RAR_ENTRIES 12 /* RAR[0], SHRA[0-10] */
108
109#define PHY_PAGE_SHIFT 5
110#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
111 ((reg) & MAX_PHY_REG_ADDRESS))
112#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */
113#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */
114
115#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002
116#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
117#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200
118
119/* PHY Wakeup Registers and defines */
120#define BM_PORT_GEN_CFG PHY_REG(BM_PORT_CTRL_PAGE, 17)
121#define BM_RCTL PHY_REG(BM_WUC_PAGE, 0)
122#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
123#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
124#define BM_WUS PHY_REG(BM_WUC_PAGE, 3)
125#define BM_RAR_L(_i) (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
126#define BM_RAR_M(_i) (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
127#define BM_RAR_H(_i) (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
128#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
129#define BM_MTA(_i) (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
130
131#define BM_RCTL_UPE 0x0001 /* Unicast Promiscuous Mode */
132#define BM_RCTL_MPE 0x0002 /* Multicast Promiscuous Mode */
133#define BM_RCTL_MO_SHIFT 3 /* Multicast Offset Shift */
134#define BM_RCTL_MO_MASK (3 << 3) /* Multicast Offset Mask */
135#define BM_RCTL_BAM 0x0020 /* Broadcast Accept Mode */
136#define BM_RCTL_PMCF 0x0040 /* Pass MAC Control Frames */
137#define BM_RCTL_RFCE 0x0080 /* Rx Flow Control Enable */
138
139#define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */
140#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
141#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
142#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
143#define HV_STATS_PAGE 778
144/* Half-duplex collision counts */
145#define HV_SCC_UPPER PHY_REG(HV_STATS_PAGE, 16) /* Single Collision */
146#define HV_SCC_LOWER PHY_REG(HV_STATS_PAGE, 17)
147#define HV_ECOL_UPPER PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. */
148#define HV_ECOL_LOWER PHY_REG(HV_STATS_PAGE, 19)
149#define HV_MCC_UPPER PHY_REG(HV_STATS_PAGE, 20) /* Multiple Collision */
150#define HV_MCC_LOWER PHY_REG(HV_STATS_PAGE, 21)
151#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision */
152#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
153#define HV_COLC_UPPER PHY_REG(HV_STATS_PAGE, 25) /* Collision */
154#define HV_COLC_LOWER PHY_REG(HV_STATS_PAGE, 26)
155#define HV_DC_UPPER PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */
156#define HV_DC_LOWER PHY_REG(HV_STATS_PAGE, 28)
157#define HV_TNCRS_UPPER PHY_REG(HV_STATS_PAGE, 29) /* Tx with no CRS */
158#define HV_TNCRS_LOWER PHY_REG(HV_STATS_PAGE, 30)
159
160#define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */
161
162#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
163#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
164
165/* SMBus Control Phy Register */
166#define CV_SMB_CTRL PHY_REG(769, 23)
167#define CV_SMB_CTRL_FORCE_SMBUS 0x0001
168
169/* I218 Ultra Low Power Configuration 1 Register */
170#define I218_ULP_CONFIG1 PHY_REG(779, 16)
171#define I218_ULP_CONFIG1_START 0x0001 /* Start auto ULP config */
172#define I218_ULP_CONFIG1_IND 0x0004 /* Pwr up from ULP indication */
173#define I218_ULP_CONFIG1_STICKY_ULP 0x0010 /* Set sticky ULP mode */
174#define I218_ULP_CONFIG1_INBAND_EXIT 0x0020 /* Inband on ULP exit */
175#define I218_ULP_CONFIG1_WOL_HOST 0x0040 /* WoL Host on ULP exit */
176#define I218_ULP_CONFIG1_RESET_TO_SMBUS 0x0100 /* Reset to SMBus mode */
177/* enable ULP even if when phy powered down via lanphypc */
178#define I218_ULP_CONFIG1_EN_ULP_LANPHYPC 0x0400
179/* disable clear of sticky ULP on PERST */
180#define I218_ULP_CONFIG1_DIS_CLR_STICKY_ON_PERST 0x0800
181#define I218_ULP_CONFIG1_DISABLE_SMB_PERST 0x1000 /* Disable on PERST# */
182
183/* SMBus Address Phy Register */
184#define HV_SMB_ADDR PHY_REG(768, 26)
185#define HV_SMB_ADDR_MASK 0x007F
186#define HV_SMB_ADDR_PEC_EN 0x0200
187#define HV_SMB_ADDR_VALID 0x0080
188#define HV_SMB_ADDR_FREQ_MASK 0x1100
189#define HV_SMB_ADDR_FREQ_LOW_SHIFT 8
190#define HV_SMB_ADDR_FREQ_HIGH_SHIFT 12
191
192/* Strapping Option Register - RO */
193#define E1000_STRAP 0x0000C
194#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
195#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
196#define E1000_STRAP_SMT_FREQ_MASK 0x00003000
197#define E1000_STRAP_SMT_FREQ_SHIFT 12
198
199/* OEM Bits Phy Register */
200#define HV_OEM_BITS PHY_REG(768, 25)
201#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
202#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
203#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
204
205/* KMRN Mode Control */
206#define HV_KMRN_MODE_CTRL PHY_REG(769, 16)
207#define HV_KMRN_MDIO_SLOW 0x0400
208
209/* KMRN FIFO Control and Status */
210#define HV_KMRN_FIFO_CTRLSTA PHY_REG(770, 16)
211#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK 0x7000
212#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT 12
213
214/* PHY Power Management Control */
215#define HV_PM_CTRL PHY_REG(770, 17)
216#define HV_PM_CTRL_K1_CLK_REQ 0x200
217#define HV_PM_CTRL_K1_ENABLE 0x4000
218
219#define I217_PLL_CLOCK_GATE_REG PHY_REG(772, 28)
220#define I217_PLL_CLOCK_GATE_MASK 0x07FF
221
222#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in ms */
223
224/* Inband Control */
225#define I217_INBAND_CTRL PHY_REG(770, 18)
226#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_MASK 0x3F00
227#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT 8
228
229/* Low Power Idle GPIO Control */
230#define I217_LPI_GPIO_CTRL PHY_REG(772, 18)
231#define I217_LPI_GPIO_CTRL_AUTO_EN_LPI 0x0800
232
233/* PHY Low Power Idle Control */
234#define I82579_LPI_CTRL PHY_REG(772, 20)
235#define I82579_LPI_CTRL_100_ENABLE 0x2000
236#define I82579_LPI_CTRL_1000_ENABLE 0x4000
237#define I82579_LPI_CTRL_ENABLE_MASK 0x6000
238#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT 0x80
239
240/* Extended Management Interface (EMI) Registers */
241#define I82579_EMI_ADDR 0x10
242#define I82579_EMI_DATA 0x11
243#define I82579_LPI_UPDATE_TIMER 0x4805 /* in 40ns units + 40 ns base value */
244#define I82579_MSE_THRESHOLD 0x084F /* 82579 Mean Square Error Threshold */
245#define I82577_MSE_THRESHOLD 0x0887 /* 82577 Mean Square Error Threshold */
246#define I82579_MSE_LINK_DOWN 0x2411 /* MSE count before dropping link */
247#define I82579_RX_CONFIG 0x3412 /* Receive configuration */
248#define I82579_LPI_PLL_SHUT 0x4412 /* LPI PLL Shut Enable */
249#define I82579_EEE_PCS_STATUS 0x182E /* IEEE MMD Register 3.1 >> 8 */
250#define I82579_EEE_CAPABILITY 0x0410 /* IEEE MMD Register 3.20 */
251#define I82579_EEE_ADVERTISEMENT 0x040E /* IEEE MMD Register 7.60 */
252#define I82579_EEE_LP_ABILITY 0x040F /* IEEE MMD Register 7.61 */
253#define I82579_EEE_100_SUPPORTED (1 << 1) /* 100BaseTx EEE */
254#define I82579_EEE_1000_SUPPORTED (1 << 2) /* 1000BaseTx EEE */
255#define I82579_LPI_100_PLL_SHUT (1 << 2) /* 100M LPI PLL Shut Enabled */
256#define I217_EEE_PCS_STATUS 0x9401 /* IEEE MMD Register 3.1 */
257#define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */
258#define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */
259#define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */
260#define I217_RX_CONFIG 0xB20C /* Receive configuration */
261
262#define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */
263#define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */
264
265/* Intel Rapid Start Technology Support */
266#define I217_PROXY_CTRL BM_PHY_REG(BM_WUC_PAGE, 70)
267#define I217_PROXY_CTRL_AUTO_DISABLE 0x0080
268#define I217_SxCTRL PHY_REG(BM_PORT_CTRL_PAGE, 28)
269#define I217_SxCTRL_ENABLE_LPI_RESET 0x1000
270#define I217_CGFREG PHY_REG(772, 29)
271#define I217_CGFREG_ENABLE_MTA_RESET 0x0002
272#define I217_MEMPWR PHY_REG(772, 26)
273#define I217_MEMPWR_DISABLE_SMB_RELEASE 0x0010
274
275/* Receive Address Initial CRC Calculation */
276#define E1000_PCH_RAICC(_n) (0x05F50 + ((_n) * 4))
277
278/* Latency Tolerance Reporting */
279#define E1000_LTRV 0x000F8
280#define E1000_LTRV_VALUE_MASK 0x000003FF
281#define E1000_LTRV_SCALE_MAX 5
282#define E1000_LTRV_SCALE_FACTOR 5
283#define E1000_LTRV_SCALE_SHIFT 10
284#define E1000_LTRV_SCALE_MASK 0x00001C00
285#define E1000_LTRV_REQ_SHIFT 15
286#define E1000_LTRV_NOSNOOP_SHIFT 16
287#define E1000_LTRV_SEND (1 << 30)
288
289/* Proprietary Latency Tolerance Reporting PCI Capability */
290#define E1000_PCI_LTR_CAP_LPT 0xA8
291
292/* Don't gate wake DMA clock */
293#define E1000_FFLT_DBG_DONT_GATE_WAKE_DMA_CLK 0x1000
294
295void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
296void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
297 bool state);
298void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
299void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
300void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
301void e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
302s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
303void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
304s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
305s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
306s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data);
307s32 e1000_set_eee_pchlan(struct e1000_hw *hw);
308s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx);
309#endif /* _E1000E_ICH8LAN_H_ */
310

source code of linux/drivers/net/ethernet/intel/e1000e/ich8lan.h