1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 *
4 * Copyright (C) 2005 Mike Isely <isely@pobox.com>
5 */
6
7#include <linux/i2c.h>
8#include <linux/module.h>
9#include <media/i2c/ir-kbd-i2c.h>
10#include "pvrusb2-i2c-core.h"
11#include "pvrusb2-hdw-internal.h"
12#include "pvrusb2-debug.h"
13#include "pvrusb2-fx2-cmd.h"
14#include "pvrusb2.h"
15
16#define trace_i2c(...) pvr2_trace(PVR2_TRACE_I2C,__VA_ARGS__)
17
18/*
19
20 This module attempts to implement a compliant I2C adapter for the pvrusb2
21 device.
22
23*/
24
25static unsigned int i2c_scan;
26module_param(i2c_scan, int, S_IRUGO|S_IWUSR);
27MODULE_PARM_DESC(i2c_scan,"scan i2c bus at insmod time");
28
29static int ir_mode[PVR_NUM] = { [0 ... PVR_NUM-1] = 1 };
30module_param_array(ir_mode, int, NULL, 0444);
31MODULE_PARM_DESC(ir_mode,"specify: 0=disable IR reception, 1=normal IR");
32
33static int pvr2_disable_ir_video;
34module_param_named(disable_autoload_ir_video, pvr2_disable_ir_video,
35 int, S_IRUGO|S_IWUSR);
36MODULE_PARM_DESC(disable_autoload_ir_video,
37 "1=do not try to autoload ir_video IR receiver");
38
39static int pvr2_i2c_write(struct pvr2_hdw *hdw, /* Context */
40 u8 i2c_addr, /* I2C address we're talking to */
41 u8 *data, /* Data to write */
42 u16 length) /* Size of data to write */
43{
44 /* Return value - default 0 means success */
45 int ret;
46
47
48 if (!data) length = 0;
49 if (length > (sizeof(hdw->cmd_buffer) - 3)) {
50 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
51 "Killing an I2C write to %u that is too large (desired=%u limit=%u)",
52 i2c_addr,
53 length,(unsigned int)(sizeof(hdw->cmd_buffer) - 3));
54 return -ENOTSUPP;
55 }
56
57 LOCK_TAKE(hdw->ctl_lock);
58
59 /* Clear the command buffer (likely to be paranoia) */
60 memset(hdw->cmd_buffer, 0, sizeof(hdw->cmd_buffer));
61
62 /* Set up command buffer for an I2C write */
63 hdw->cmd_buffer[0] = FX2CMD_I2C_WRITE; /* write prefix */
64 hdw->cmd_buffer[1] = i2c_addr; /* i2c addr of chip */
65 hdw->cmd_buffer[2] = length; /* length of what follows */
66 if (length) memcpy(hdw->cmd_buffer + 3, data, length);
67
68 /* Do the operation */
69 ret = pvr2_send_request(hdw,
70 write_ptr: hdw->cmd_buffer,
71 write_len: length + 3,
72 read_ptr: hdw->cmd_buffer,
73 read_len: 1);
74 if (!ret) {
75 if (hdw->cmd_buffer[0] != 8) {
76 ret = -EIO;
77 if (hdw->cmd_buffer[0] != 7) {
78 trace_i2c("unexpected status from i2_write[%d]: %d",
79 i2c_addr,hdw->cmd_buffer[0]);
80 }
81 }
82 }
83
84 LOCK_GIVE(hdw->ctl_lock);
85
86 return ret;
87}
88
89static int pvr2_i2c_read(struct pvr2_hdw *hdw, /* Context */
90 u8 i2c_addr, /* I2C address we're talking to */
91 u8 *data, /* Data to write */
92 u16 dlen, /* Size of data to write */
93 u8 *res, /* Where to put data we read */
94 u16 rlen) /* Amount of data to read */
95{
96 /* Return value - default 0 means success */
97 int ret;
98
99
100 if (!data) dlen = 0;
101 if (dlen > (sizeof(hdw->cmd_buffer) - 4)) {
102 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
103 "Killing an I2C read to %u that has wlen too large (desired=%u limit=%u)",
104 i2c_addr,
105 dlen,(unsigned int)(sizeof(hdw->cmd_buffer) - 4));
106 return -ENOTSUPP;
107 }
108 if (res && (rlen > (sizeof(hdw->cmd_buffer) - 1))) {
109 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
110 "Killing an I2C read to %u that has rlen too large (desired=%u limit=%u)",
111 i2c_addr,
112 rlen,(unsigned int)(sizeof(hdw->cmd_buffer) - 1));
113 return -ENOTSUPP;
114 }
115
116 LOCK_TAKE(hdw->ctl_lock);
117
118 /* Clear the command buffer (likely to be paranoia) */
119 memset(hdw->cmd_buffer, 0, sizeof(hdw->cmd_buffer));
120
121 /* Set up command buffer for an I2C write followed by a read */
122 hdw->cmd_buffer[0] = FX2CMD_I2C_READ; /* read prefix */
123 hdw->cmd_buffer[1] = dlen; /* arg length */
124 hdw->cmd_buffer[2] = rlen; /* answer length. Device will send one
125 more byte (status). */
126 hdw->cmd_buffer[3] = i2c_addr; /* i2c addr of chip */
127 if (dlen) memcpy(hdw->cmd_buffer + 4, data, dlen);
128
129 /* Do the operation */
130 ret = pvr2_send_request(hdw,
131 write_ptr: hdw->cmd_buffer,
132 write_len: 4 + dlen,
133 read_ptr: hdw->cmd_buffer,
134 read_len: rlen + 1);
135 if (!ret) {
136 if (hdw->cmd_buffer[0] != 8) {
137 ret = -EIO;
138 if (hdw->cmd_buffer[0] != 7) {
139 trace_i2c("unexpected status from i2_read[%d]: %d",
140 i2c_addr,hdw->cmd_buffer[0]);
141 }
142 }
143 }
144
145 /* Copy back the result */
146 if (res && rlen) {
147 if (ret) {
148 /* Error, just blank out the return buffer */
149 memset(res, 0, rlen);
150 } else {
151 memcpy(res, hdw->cmd_buffer + 1, rlen);
152 }
153 }
154
155 LOCK_GIVE(hdw->ctl_lock);
156
157 return ret;
158}
159
160/* This is the common low level entry point for doing I2C operations to the
161 hardware. */
162static int pvr2_i2c_basic_op(struct pvr2_hdw *hdw,
163 u8 i2c_addr,
164 u8 *wdata,
165 u16 wlen,
166 u8 *rdata,
167 u16 rlen)
168{
169 if (!rdata) rlen = 0;
170 if (!wdata) wlen = 0;
171 if (rlen || !wlen) {
172 return pvr2_i2c_read(hdw,i2c_addr,data: wdata,dlen: wlen,res: rdata,rlen);
173 } else {
174 return pvr2_i2c_write(hdw,i2c_addr,data: wdata,length: wlen);
175 }
176}
177
178
179/* This is a special entry point for cases of I2C transaction attempts to
180 the IR receiver. The implementation here simulates the IR receiver by
181 issuing a command to the FX2 firmware and using that response to return
182 what the real I2C receiver would have returned. We use this for 24xxx
183 devices, where the IR receiver chip has been removed and replaced with
184 FX2 related logic. */
185static int i2c_24xxx_ir(struct pvr2_hdw *hdw,
186 u8 i2c_addr,u8 *wdata,u16 wlen,u8 *rdata,u16 rlen)
187{
188 u8 dat[4];
189 unsigned int stat;
190
191 if (!(rlen || wlen)) {
192 /* This is a probe attempt. Just let it succeed. */
193 return 0;
194 }
195
196 /* We don't understand this kind of transaction */
197 if ((wlen != 0) || (rlen == 0)) return -EIO;
198
199 if (rlen < 3) {
200 /* Mike Isely <isely@pobox.com> Appears to be a probe
201 attempt from lirc. Just fill in zeroes and return. If
202 we try instead to do the full transaction here, then bad
203 things seem to happen within the lirc driver module
204 (version 0.8.0-7 sources from Debian, when run under
205 vanilla 2.6.17.6 kernel) - and I don't have the patience
206 to chase it down. */
207 if (rlen > 0) rdata[0] = 0;
208 if (rlen > 1) rdata[1] = 0;
209 return 0;
210 }
211
212 /* Issue a command to the FX2 to read the IR receiver. */
213 LOCK_TAKE(hdw->ctl_lock); do {
214 hdw->cmd_buffer[0] = FX2CMD_GET_IR_CODE;
215 stat = pvr2_send_request(hdw,
216 write_ptr: hdw->cmd_buffer,write_len: 1,
217 read_ptr: hdw->cmd_buffer,read_len: 4);
218 dat[0] = hdw->cmd_buffer[0];
219 dat[1] = hdw->cmd_buffer[1];
220 dat[2] = hdw->cmd_buffer[2];
221 dat[3] = hdw->cmd_buffer[3];
222 } while (0); LOCK_GIVE(hdw->ctl_lock);
223
224 /* Give up if that operation failed. */
225 if (stat != 0) return stat;
226
227 /* Mangle the results into something that looks like the real IR
228 receiver. */
229 rdata[2] = 0xc1;
230 if (dat[0] != 1) {
231 /* No code received. */
232 rdata[0] = 0;
233 rdata[1] = 0;
234 } else {
235 u16 val;
236 /* Mash the FX2 firmware-provided IR code into something
237 that the normal i2c chip-level driver expects. */
238 val = dat[1];
239 val <<= 8;
240 val |= dat[2];
241 val >>= 1;
242 val &= ~0x0003;
243 val |= 0x8000;
244 rdata[0] = (val >> 8) & 0xffu;
245 rdata[1] = val & 0xffu;
246 }
247
248 return 0;
249}
250
251/* This is a special entry point that is entered if an I2C operation is
252 attempted to a wm8775 chip on model 24xxx hardware. Autodetect of this
253 part doesn't work, but we know it is really there. So let's look for
254 the autodetect attempt and just return success if we see that. */
255static int i2c_hack_wm8775(struct pvr2_hdw *hdw,
256 u8 i2c_addr,u8 *wdata,u16 wlen,u8 *rdata,u16 rlen)
257{
258 if (!(rlen || wlen)) {
259 // This is a probe attempt. Just let it succeed.
260 return 0;
261 }
262 return pvr2_i2c_basic_op(hdw,i2c_addr,wdata,wlen,rdata,rlen);
263}
264
265/* This is an entry point designed to always fail any attempt to perform a
266 transfer. We use this to cause certain I2C addresses to not be
267 probed. */
268static int i2c_black_hole(struct pvr2_hdw *hdw,
269 u8 i2c_addr,u8 *wdata,u16 wlen,u8 *rdata,u16 rlen)
270{
271 return -EIO;
272}
273
274/* This is a special entry point that is entered if an I2C operation is
275 attempted to a cx25840 chip on model 24xxx hardware. This chip can
276 sometimes wedge itself. Worse still, when this happens msp3400 can
277 falsely detect this part and then the system gets hosed up after msp3400
278 gets confused and dies. What we want to do here is try to keep msp3400
279 away and also try to notice if the chip is wedged and send a warning to
280 the system log. */
281static int i2c_hack_cx25840(struct pvr2_hdw *hdw,
282 u8 i2c_addr,u8 *wdata,u16 wlen,u8 *rdata,u16 rlen)
283{
284 int ret;
285 unsigned int subaddr;
286 u8 wbuf[2];
287 int state = hdw->i2c_cx25840_hack_state;
288
289 if (!(rlen || wlen)) {
290 // Probe attempt - always just succeed and don't bother the
291 // hardware (this helps to make the state machine further
292 // down somewhat easier).
293 return 0;
294 }
295
296 if (state == 3) {
297 return pvr2_i2c_basic_op(hdw,i2c_addr,wdata,wlen,rdata,rlen);
298 }
299
300 /* We're looking for the exact pattern where the revision register
301 is being read. The cx25840 module will always look at the
302 revision register first. Any other pattern of access therefore
303 has to be a probe attempt from somebody else so we'll reject it.
304 Normally we could just let each client just probe the part
305 anyway, but when the cx25840 is wedged, msp3400 will get a false
306 positive and that just screws things up... */
307
308 if (wlen == 0) {
309 switch (state) {
310 case 1: subaddr = 0x0100; break;
311 case 2: subaddr = 0x0101; break;
312 default: goto fail;
313 }
314 } else if (wlen == 2) {
315 subaddr = (wdata[0] << 8) | wdata[1];
316 switch (subaddr) {
317 case 0x0100: state = 1; break;
318 case 0x0101: state = 2; break;
319 default: goto fail;
320 }
321 } else {
322 goto fail;
323 }
324 if (!rlen) goto success;
325 state = 0;
326 if (rlen != 1) goto fail;
327
328 /* If we get to here then we have a legitimate read for one of the
329 two revision bytes, so pass it through. */
330 wbuf[0] = subaddr >> 8;
331 wbuf[1] = subaddr;
332 ret = pvr2_i2c_basic_op(hdw,i2c_addr,wdata: wbuf,wlen: 2,rdata,rlen);
333
334 if ((ret != 0) || (*rdata == 0x04) || (*rdata == 0x0a)) {
335 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
336 "***WARNING*** Detected a wedged cx25840 chip; the device will not work.");
337 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
338 "***WARNING*** Try power cycling the pvrusb2 device.");
339 pvr2_trace(PVR2_TRACE_ERROR_LEGS,
340 "***WARNING*** Disabling further access to the device to prevent other foul-ups.");
341 // This blocks all further communication with the part.
342 hdw->i2c_func[0x44] = NULL;
343 pvr2_hdw_render_useless(hdw);
344 goto fail;
345 }
346
347 /* Success! */
348 pvr2_trace(PVR2_TRACE_CHIPS,"cx25840 appears to be OK.");
349 state = 3;
350
351 success:
352 hdw->i2c_cx25840_hack_state = state;
353 return 0;
354
355 fail:
356 hdw->i2c_cx25840_hack_state = state;
357 return -EIO;
358}
359
360/* This is a very, very limited I2C adapter implementation. We can only
361 support what we actually know will work on the device... */
362static int pvr2_i2c_xfer(struct i2c_adapter *i2c_adap,
363 struct i2c_msg msgs[],
364 int num)
365{
366 int ret = -ENOTSUPP;
367 pvr2_i2c_func funcp = NULL;
368 struct pvr2_hdw *hdw = (struct pvr2_hdw *)(i2c_adap->algo_data);
369
370 if (!num) {
371 ret = -EINVAL;
372 goto done;
373 }
374 if (msgs[0].addr < PVR2_I2C_FUNC_CNT) {
375 funcp = hdw->i2c_func[msgs[0].addr];
376 }
377 if (!funcp) {
378 ret = -EIO;
379 goto done;
380 }
381
382 if (num == 1) {
383 if (msgs[0].flags & I2C_M_RD) {
384 /* Simple read */
385 u16 tcnt,bcnt,offs;
386 if (!msgs[0].len) {
387 /* Length == 0 read. This is a probe. */
388 if (funcp(hdw,msgs[0].addr,NULL,0,NULL,0)) {
389 ret = -EIO;
390 goto done;
391 }
392 ret = 1;
393 goto done;
394 }
395 /* If the read is short enough we'll do the whole
396 thing atomically. Otherwise we have no choice
397 but to break apart the reads. */
398 tcnt = msgs[0].len;
399 offs = 0;
400 while (tcnt) {
401 bcnt = tcnt;
402 if (bcnt > sizeof(hdw->cmd_buffer)-1) {
403 bcnt = sizeof(hdw->cmd_buffer)-1;
404 }
405 if (funcp(hdw,msgs[0].addr,NULL,0,
406 msgs[0].buf+offs,bcnt)) {
407 ret = -EIO;
408 goto done;
409 }
410 offs += bcnt;
411 tcnt -= bcnt;
412 }
413 ret = 1;
414 goto done;
415 } else {
416 /* Simple write */
417 ret = 1;
418 if (funcp(hdw,msgs[0].addr,
419 msgs[0].buf,msgs[0].len,NULL,0)) {
420 ret = -EIO;
421 }
422 goto done;
423 }
424 } else if (num == 2) {
425 if (msgs[0].addr != msgs[1].addr) {
426 trace_i2c("i2c refusing 2 phase transfer with conflicting target addresses");
427 ret = -ENOTSUPP;
428 goto done;
429 }
430 if ((!((msgs[0].flags & I2C_M_RD))) &&
431 (msgs[1].flags & I2C_M_RD)) {
432 u16 tcnt,bcnt,wcnt,offs;
433 /* Write followed by atomic read. If the read
434 portion is short enough we'll do the whole thing
435 atomically. Otherwise we have no choice but to
436 break apart the reads. */
437 tcnt = msgs[1].len;
438 wcnt = msgs[0].len;
439 offs = 0;
440 while (tcnt || wcnt) {
441 bcnt = tcnt;
442 if (bcnt > sizeof(hdw->cmd_buffer)-1) {
443 bcnt = sizeof(hdw->cmd_buffer)-1;
444 }
445 if (funcp(hdw,msgs[0].addr,
446 msgs[0].buf,wcnt,
447 msgs[1].buf+offs,bcnt)) {
448 ret = -EIO;
449 goto done;
450 }
451 offs += bcnt;
452 tcnt -= bcnt;
453 wcnt = 0;
454 }
455 ret = 2;
456 goto done;
457 } else {
458 trace_i2c("i2c refusing complex transfer read0=%d read1=%d",
459 (msgs[0].flags & I2C_M_RD),
460 (msgs[1].flags & I2C_M_RD));
461 }
462 } else {
463 trace_i2c("i2c refusing %d phase transfer",num);
464 }
465
466 done:
467 if (pvrusb2_debug & PVR2_TRACE_I2C_TRAF) {
468 unsigned int idx,offs,cnt;
469 for (idx = 0; idx < num; idx++) {
470 cnt = msgs[idx].len;
471 pr_info("pvrusb2 i2c xfer %u/%u: addr=0x%x len=%d %s",
472 idx+1,num,
473 msgs[idx].addr,
474 cnt,
475 (msgs[idx].flags & I2C_M_RD ?
476 "read" : "write"));
477 if ((ret > 0) || !(msgs[idx].flags & I2C_M_RD)) {
478 if (cnt > 8) cnt = 8;
479 pr_cont(" [");
480 for (offs = 0; offs < cnt; offs++) {
481 if (offs) pr_cont(" ");
482 pr_cont("%02x", msgs[idx].buf[offs]);
483 }
484 if (offs < cnt) pr_cont(" ...");
485 pr_cont("]");
486 }
487 if (idx+1 == num) {
488 pr_cont(" result=%d", ret);
489 }
490 pr_cont("\n");
491 }
492 if (!num) {
493 pr_info("pvrusb2 i2c xfer null transfer result=%d\n",
494 ret);
495 }
496 }
497 return ret;
498}
499
500static u32 pvr2_i2c_functionality(struct i2c_adapter *adap)
501{
502 return I2C_FUNC_SMBUS_EMUL | I2C_FUNC_I2C;
503}
504
505static const struct i2c_algorithm pvr2_i2c_algo_template = {
506 .master_xfer = pvr2_i2c_xfer,
507 .functionality = pvr2_i2c_functionality,
508};
509
510static const struct i2c_adapter pvr2_i2c_adap_template = {
511 .owner = THIS_MODULE,
512 .class = 0,
513};
514
515
516/* Return true if device exists at given address */
517static int do_i2c_probe(struct pvr2_hdw *hdw, int addr)
518{
519 struct i2c_msg msg[1];
520 int rc;
521 msg[0].addr = 0;
522 msg[0].flags = I2C_M_RD;
523 msg[0].len = 0;
524 msg[0].buf = NULL;
525 msg[0].addr = addr;
526 rc = i2c_transfer(adap: &hdw->i2c_adap, msgs: msg, ARRAY_SIZE(msg));
527 return rc == 1;
528}
529
530static void do_i2c_scan(struct pvr2_hdw *hdw)
531{
532 int i;
533 pr_info("%s: i2c scan beginning\n", hdw->name);
534 for (i = 0; i < 128; i++) {
535 if (do_i2c_probe(hdw, addr: i)) {
536 pr_info("%s: i2c scan: found device @ 0x%x\n",
537 hdw->name, i);
538 }
539 }
540 pr_info("%s: i2c scan done.\n", hdw->name);
541}
542
543static void pvr2_i2c_register_ir(struct pvr2_hdw *hdw)
544{
545 struct i2c_board_info info;
546 struct IR_i2c_init_data *init_data = &hdw->ir_init_data;
547 if (pvr2_disable_ir_video) {
548 pvr2_trace(PVR2_TRACE_INFO,
549 "Automatic binding of ir_video has been disabled.");
550 return;
551 }
552 memset(&info, 0, sizeof(struct i2c_board_info));
553 switch (hdw->ir_scheme_active) {
554 case PVR2_IR_SCHEME_24XXX: /* FX2-controlled IR */
555 case PVR2_IR_SCHEME_29XXX: /* Original 29xxx device */
556 init_data->ir_codes = RC_MAP_HAUPPAUGE;
557 init_data->internal_get_key_func = IR_KBD_GET_KEY_HAUP;
558 init_data->type = RC_PROTO_BIT_RC5;
559 init_data->name = hdw->hdw_desc->description;
560 init_data->polling_interval = 100; /* ms From ir-kbd-i2c */
561 /* IR Receiver */
562 info.addr = 0x18;
563 info.platform_data = init_data;
564 strscpy(info.type, "ir_video", I2C_NAME_SIZE);
565 pvr2_trace(PVR2_TRACE_INFO, "Binding %s to i2c address 0x%02x.",
566 info.type, info.addr);
567 i2c_new_client_device(adap: &hdw->i2c_adap, info: &info);
568 break;
569 case PVR2_IR_SCHEME_ZILOG: /* HVR-1950 style */
570 case PVR2_IR_SCHEME_24XXX_MCE: /* 24xxx MCE device */
571 init_data->ir_codes = RC_MAP_HAUPPAUGE;
572 init_data->internal_get_key_func = IR_KBD_GET_KEY_HAUP_XVR;
573 init_data->type = RC_PROTO_BIT_RC5 | RC_PROTO_BIT_RC6_MCE |
574 RC_PROTO_BIT_RC6_6A_32;
575 init_data->name = hdw->hdw_desc->description;
576 /* IR Transceiver */
577 info.addr = 0x71;
578 info.platform_data = init_data;
579 strscpy(info.type, "ir_z8f0811_haup", I2C_NAME_SIZE);
580 pvr2_trace(PVR2_TRACE_INFO, "Binding %s to i2c address 0x%02x.",
581 info.type, info.addr);
582 i2c_new_client_device(adap: &hdw->i2c_adap, info: &info);
583 break;
584 default:
585 /* The device either doesn't support I2C-based IR or we
586 don't know (yet) how to operate IR on the device. */
587 break;
588 }
589}
590
591void pvr2_i2c_core_init(struct pvr2_hdw *hdw)
592{
593 unsigned int idx;
594
595 /* The default action for all possible I2C addresses is just to do
596 the transfer normally. */
597 for (idx = 0; idx < PVR2_I2C_FUNC_CNT; idx++) {
598 hdw->i2c_func[idx] = pvr2_i2c_basic_op;
599 }
600
601 /* However, deal with various special cases for 24xxx hardware. */
602 if (ir_mode[hdw->unit_number] == 0) {
603 pr_info("%s: IR disabled\n", hdw->name);
604 hdw->i2c_func[0x18] = i2c_black_hole;
605 } else if (ir_mode[hdw->unit_number] == 1) {
606 if (hdw->ir_scheme_active == PVR2_IR_SCHEME_24XXX) {
607 /* Set up translation so that our IR looks like a
608 29xxx device */
609 hdw->i2c_func[0x18] = i2c_24xxx_ir;
610 }
611 }
612 if (hdw->hdw_desc->flag_has_cx25840) {
613 hdw->i2c_func[0x44] = i2c_hack_cx25840;
614 }
615 if (hdw->hdw_desc->flag_has_wm8775) {
616 hdw->i2c_func[0x1b] = i2c_hack_wm8775;
617 }
618
619 // Configure the adapter and set up everything else related to it.
620 hdw->i2c_adap = pvr2_i2c_adap_template;
621 hdw->i2c_algo = pvr2_i2c_algo_template;
622 strscpy(hdw->i2c_adap.name, hdw->name, sizeof(hdw->i2c_adap.name));
623 hdw->i2c_adap.dev.parent = &hdw->usb_dev->dev;
624 hdw->i2c_adap.algo = &hdw->i2c_algo;
625 hdw->i2c_adap.algo_data = hdw;
626 hdw->i2c_linked = !0;
627 i2c_set_adapdata(adap: &hdw->i2c_adap, data: &hdw->v4l2_dev);
628 i2c_add_adapter(adap: &hdw->i2c_adap);
629 if (hdw->i2c_func[0x18] == i2c_24xxx_ir) {
630 /* Probe for a different type of IR receiver on this
631 device. This is really the only way to differentiate
632 older 24xxx devices from 24xxx variants that include an
633 IR blaster. If the IR blaster is present, the IR
634 receiver is part of that chip and thus we must disable
635 the emulated IR receiver. */
636 if (do_i2c_probe(hdw, addr: 0x71)) {
637 pvr2_trace(PVR2_TRACE_INFO,
638 "Device has newer IR hardware; disabling unneeded virtual IR device");
639 hdw->i2c_func[0x18] = NULL;
640 /* Remember that this is a different device... */
641 hdw->ir_scheme_active = PVR2_IR_SCHEME_24XXX_MCE;
642 }
643 }
644 if (i2c_scan) do_i2c_scan(hdw);
645
646 pvr2_i2c_register_ir(hdw);
647}
648
649void pvr2_i2c_core_done(struct pvr2_hdw *hdw)
650{
651 if (hdw->i2c_linked) {
652 i2c_del_adapter(adap: &hdw->i2c_adap);
653 hdw->i2c_linked = 0;
654 }
655}
656

source code of linux/drivers/media/usb/pvrusb2/pvrusb2-i2c-core.c