1/* SPDX-License-Identifier: GPL-2.0-only */
2/*
3 * linux/amba/pl08x.h - ARM PrimeCell DMA Controller driver
4 *
5 * Copyright (C) 2005 ARM Ltd
6 * Copyright (C) 2010 ST-Ericsson SA
7 *
8 * pl08x information required by platform code
9 *
10 * Please credit ARM.com
11 * Documentation: ARM DDI 0196D
12 */
13
14#ifndef AMBA_PL08X_H
15#define AMBA_PL08X_H
16
17/* We need sizes of structs from this header */
18#include <linux/dmaengine.h>
19#include <linux/interrupt.h>
20
21struct pl08x_driver_data;
22struct pl08x_phy_chan;
23struct pl08x_txd;
24
25/* Bitmasks for selecting AHB ports for DMA transfers */
26enum {
27 PL08X_AHB1 = (1 << 0),
28 PL08X_AHB2 = (1 << 1)
29};
30
31/**
32 * struct pl08x_channel_data - data structure to pass info between
33 * platform and PL08x driver regarding channel configuration
34 * @bus_id: name of this device channel, not just a device name since
35 * devices may have more than one channel e.g. "foo_tx"
36 * @min_signal: the minimum DMA signal number to be muxed in for this
37 * channel (for platforms supporting muxed signals). If you have
38 * static assignments, make sure this is set to the assigned signal
39 * number, PL08x have 16 possible signals in number 0 thru 15 so
40 * when these are not enough they often get muxed (in hardware)
41 * disabling simultaneous use of the same channel for two devices.
42 * @max_signal: the maximum DMA signal number to be muxed in for
43 * the channel. Set to the same as min_signal for
44 * devices with static assignments
45 * @muxval: a number usually used to poke into some mux regiser to
46 * mux in the signal to this channel
47 * @addr: source/target address in physical memory for this DMA channel,
48 * can be the address of a FIFO register for burst requests for example.
49 * This can be left undefined if the PrimeCell API is used for configuring
50 * this.
51 * @single: the device connected to this channel will request single DMA
52 * transfers, not bursts. (Bursts are default.)
53 * @periph_buses: the device connected to this channel is accessible via
54 * these buses (use PL08X_AHB1 | PL08X_AHB2).
55 */
56struct pl08x_channel_data {
57 const char *bus_id;
58 int min_signal;
59 int max_signal;
60 u32 muxval;
61 dma_addr_t addr;
62 bool single;
63 u8 periph_buses;
64};
65
66enum pl08x_burst_size {
67 PL08X_BURST_SZ_1,
68 PL08X_BURST_SZ_4,
69 PL08X_BURST_SZ_8,
70 PL08X_BURST_SZ_16,
71 PL08X_BURST_SZ_32,
72 PL08X_BURST_SZ_64,
73 PL08X_BURST_SZ_128,
74 PL08X_BURST_SZ_256,
75};
76
77enum pl08x_bus_width {
78 PL08X_BUS_WIDTH_8_BITS,
79 PL08X_BUS_WIDTH_16_BITS,
80 PL08X_BUS_WIDTH_32_BITS,
81};
82
83/**
84 * struct pl08x_platform_data - the platform configuration for the PL08x
85 * PrimeCells.
86 * @slave_channels: the channels defined for the different devices on the
87 * platform, all inclusive, including multiplexed channels. The available
88 * physical channels will be multiplexed around these signals as they are
89 * requested, just enumerate all possible channels.
90 * @num_slave_channels: number of elements in the slave channel array
91 * @memcpy_burst_size: the appropriate burst size for memcpy operations
92 * @memcpy_bus_width: memory bus width
93 * @memcpy_prot_buff: whether memcpy DMA is bufferable
94 * @memcpy_prot_cache: whether memcpy DMA is cacheable
95 * @get_xfer_signal: request a physical signal to be used for a DMA transfer
96 * immediately: if there is some multiplexing or similar blocking the use
97 * of the channel the transfer can be denied by returning less than zero,
98 * else it returns the allocated signal number
99 * @put_xfer_signal: indicate to the platform that this physical signal is not
100 * running any DMA transfer and multiplexing can be recycled
101 * @lli_buses: buses which LLIs can be fetched from: PL08X_AHB1 | PL08X_AHB2
102 * @mem_buses: buses which memory can be accessed from: PL08X_AHB1 | PL08X_AHB2
103 * @slave_map: DMA slave matching table
104 * @slave_map_len: number of elements in @slave_map
105 */
106struct pl08x_platform_data {
107 struct pl08x_channel_data *slave_channels;
108 unsigned int num_slave_channels;
109 enum pl08x_burst_size memcpy_burst_size;
110 enum pl08x_bus_width memcpy_bus_width;
111 bool memcpy_prot_buff;
112 bool memcpy_prot_cache;
113 int (*get_xfer_signal)(const struct pl08x_channel_data *);
114 void (*put_xfer_signal)(const struct pl08x_channel_data *, int);
115 u8 lli_buses;
116 u8 mem_buses;
117 const struct dma_slave_map *slave_map;
118 int slave_map_len;
119};
120
121#ifdef CONFIG_AMBA_PL08X
122bool pl08x_filter_id(struct dma_chan *chan, void *chan_id);
123#else
124static inline bool pl08x_filter_id(struct dma_chan *chan, void *chan_id)
125{
126 return false;
127}
128#endif
129
130#endif /* AMBA_PL08X_H */
131

source code of linux/include/linux/amba/pl08x.h