1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright (C) 2015-2016 Socionext Inc.
4 * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
5 */
6
7#define pr_fmt(fmt) "uniphier: " fmt
8
9#include <linux/bitops.h>
10#include <linux/init.h>
11#include <linux/io.h>
12#include <linux/log2.h>
13#include <linux/of_address.h>
14#include <linux/slab.h>
15#include <asm/hardware/cache-uniphier.h>
16#include <asm/outercache.h>
17
18/* control registers */
19#define UNIPHIER_SSCC 0x0 /* Control Register */
20#define UNIPHIER_SSCC_BST BIT(20) /* UCWG burst read */
21#define UNIPHIER_SSCC_ACT BIT(19) /* Inst-Data separate */
22#define UNIPHIER_SSCC_WTG BIT(18) /* WT gathering on */
23#define UNIPHIER_SSCC_PRD BIT(17) /* enable pre-fetch */
24#define UNIPHIER_SSCC_ON BIT(0) /* enable cache */
25#define UNIPHIER_SSCLPDAWCR 0x30 /* Unified/Data Active Way Control */
26#define UNIPHIER_SSCLPIAWCR 0x34 /* Instruction Active Way Control */
27
28/* revision registers */
29#define UNIPHIER_SSCID 0x0 /* ID Register */
30
31/* operation registers */
32#define UNIPHIER_SSCOPE 0x244 /* Cache Operation Primitive Entry */
33#define UNIPHIER_SSCOPE_CM_INV 0x0 /* invalidate */
34#define UNIPHIER_SSCOPE_CM_CLEAN 0x1 /* clean */
35#define UNIPHIER_SSCOPE_CM_FLUSH 0x2 /* flush */
36#define UNIPHIER_SSCOPE_CM_SYNC 0x8 /* sync (drain bufs) */
37#define UNIPHIER_SSCOPE_CM_FLUSH_PREFETCH 0x9 /* flush p-fetch buf */
38#define UNIPHIER_SSCOQM 0x248 /* Cache Operation Queue Mode */
39#define UNIPHIER_SSCOQM_S_MASK (0x3 << 17)
40#define UNIPHIER_SSCOQM_S_RANGE (0x0 << 17)
41#define UNIPHIER_SSCOQM_S_ALL (0x1 << 17)
42#define UNIPHIER_SSCOQM_CE BIT(15) /* notify completion */
43#define UNIPHIER_SSCOQM_CM_INV 0x0 /* invalidate */
44#define UNIPHIER_SSCOQM_CM_CLEAN 0x1 /* clean */
45#define UNIPHIER_SSCOQM_CM_FLUSH 0x2 /* flush */
46#define UNIPHIER_SSCOQAD 0x24c /* Cache Operation Queue Address */
47#define UNIPHIER_SSCOQSZ 0x250 /* Cache Operation Queue Size */
48#define UNIPHIER_SSCOPPQSEF 0x25c /* Cache Operation Queue Set Complete*/
49#define UNIPHIER_SSCOPPQSEF_FE BIT(1)
50#define UNIPHIER_SSCOPPQSEF_OE BIT(0)
51#define UNIPHIER_SSCOLPQS 0x260 /* Cache Operation Queue Status */
52#define UNIPHIER_SSCOLPQS_EF BIT(2)
53#define UNIPHIER_SSCOLPQS_EST BIT(1)
54#define UNIPHIER_SSCOLPQS_QST BIT(0)
55
56/* Is the operation region specified by address range? */
57#define UNIPHIER_SSCOQM_S_IS_RANGE(op) \
58 ((op & UNIPHIER_SSCOQM_S_MASK) == UNIPHIER_SSCOQM_S_RANGE)
59
60/**
61 * struct uniphier_cache_data - UniPhier outer cache specific data
62 *
63 * @ctrl_base: virtual base address of control registers
64 * @rev_base: virtual base address of revision registers
65 * @op_base: virtual base address of operation registers
66 * @way_ctrl_base: virtual address of the way control registers for this
67 * SoC revision
68 * @way_mask: each bit specifies if the way is present
69 * @nsets: number of associativity sets
70 * @line_size: line size in bytes
71 * @range_op_max_size: max size that can be handled by a single range operation
72 * @list: list node to include this level in the whole cache hierarchy
73 */
74struct uniphier_cache_data {
75 void __iomem *ctrl_base;
76 void __iomem *rev_base;
77 void __iomem *op_base;
78 void __iomem *way_ctrl_base;
79 u32 way_mask;
80 u32 nsets;
81 u32 line_size;
82 u32 range_op_max_size;
83 struct list_head list;
84};
85
86/*
87 * List of the whole outer cache hierarchy. This list is only modified during
88 * the early boot stage, so no mutex is taken for the access to the list.
89 */
90static LIST_HEAD(uniphier_cache_list);
91
92/**
93 * __uniphier_cache_sync - perform a sync point for a particular cache level
94 *
95 * @data: cache controller specific data
96 */
97static void __uniphier_cache_sync(struct uniphier_cache_data *data)
98{
99 /* This sequence need not be atomic. Do not disable IRQ. */
100 writel_relaxed(UNIPHIER_SSCOPE_CM_SYNC,
101 data->op_base + UNIPHIER_SSCOPE);
102 /* need a read back to confirm */
103 readl_relaxed(data->op_base + UNIPHIER_SSCOPE);
104}
105
106/**
107 * __uniphier_cache_maint_common - run a queue operation for a particular level
108 *
109 * @data: cache controller specific data
110 * @start: start address of range operation (don't care for "all" operation)
111 * @size: data size of range operation (don't care for "all" operation)
112 * @operation: flags to specify the desired cache operation
113 */
114static void __uniphier_cache_maint_common(struct uniphier_cache_data *data,
115 unsigned long start,
116 unsigned long size,
117 u32 operation)
118{
119 unsigned long flags;
120
121 /*
122 * No spin lock is necessary here because:
123 *
124 * [1] This outer cache controller is able to accept maintenance
125 * operations from multiple CPUs at a time in an SMP system; if a
126 * maintenance operation is under way and another operation is issued,
127 * the new one is stored in the queue. The controller performs one
128 * operation after another. If the queue is full, the status register,
129 * UNIPHIER_SSCOPPQSEF, indicates that the queue registration has
130 * failed. The status registers, UNIPHIER_{SSCOPPQSEF, SSCOLPQS}, have
131 * different instances for each CPU, i.e. each CPU can track the status
132 * of the maintenance operations triggered by itself.
133 *
134 * [2] The cache command registers, UNIPHIER_{SSCOQM, SSCOQAD, SSCOQSZ,
135 * SSCOQWN}, are shared between multiple CPUs, but the hardware still
136 * guarantees the registration sequence is atomic; the write access to
137 * them are arbitrated by the hardware. The first accessor to the
138 * register, UNIPHIER_SSCOQM, holds the access right and it is released
139 * by reading the status register, UNIPHIER_SSCOPPQSEF. While one CPU
140 * is holding the access right, other CPUs fail to register operations.
141 * One CPU should not hold the access right for a long time, so local
142 * IRQs should be disabled while the following sequence.
143 */
144 local_irq_save(flags);
145
146 /* clear the complete notification flag */
147 writel_relaxed(UNIPHIER_SSCOLPQS_EF, data->op_base + UNIPHIER_SSCOLPQS);
148
149 do {
150 /* set cache operation */
151 writel_relaxed(UNIPHIER_SSCOQM_CE | operation,
152 data->op_base + UNIPHIER_SSCOQM);
153
154 /* set address range if needed */
155 if (likely(UNIPHIER_SSCOQM_S_IS_RANGE(operation))) {
156 writel_relaxed(start, data->op_base + UNIPHIER_SSCOQAD);
157 writel_relaxed(size, data->op_base + UNIPHIER_SSCOQSZ);
158 }
159 } while (unlikely(readl_relaxed(data->op_base + UNIPHIER_SSCOPPQSEF) &
160 (UNIPHIER_SSCOPPQSEF_FE | UNIPHIER_SSCOPPQSEF_OE)));
161
162 /* wait until the operation is completed */
163 while (likely(readl_relaxed(data->op_base + UNIPHIER_SSCOLPQS) !=
164 UNIPHIER_SSCOLPQS_EF))
165 cpu_relax();
166
167 local_irq_restore(flags);
168}
169
170static void __uniphier_cache_maint_all(struct uniphier_cache_data *data,
171 u32 operation)
172{
173 __uniphier_cache_maint_common(data, start: 0, size: 0,
174 UNIPHIER_SSCOQM_S_ALL | operation);
175
176 __uniphier_cache_sync(data);
177}
178
179static void __uniphier_cache_maint_range(struct uniphier_cache_data *data,
180 unsigned long start, unsigned long end,
181 u32 operation)
182{
183 unsigned long size;
184
185 /*
186 * If the start address is not aligned,
187 * perform a cache operation for the first cache-line
188 */
189 start = start & ~(data->line_size - 1);
190
191 size = end - start;
192
193 if (unlikely(size >= (unsigned long)(-data->line_size))) {
194 /* this means cache operation for all range */
195 __uniphier_cache_maint_all(data, operation);
196 return;
197 }
198
199 /*
200 * If the end address is not aligned,
201 * perform a cache operation for the last cache-line
202 */
203 size = ALIGN(size, data->line_size);
204
205 while (size) {
206 unsigned long chunk_size = min_t(unsigned long, size,
207 data->range_op_max_size);
208
209 __uniphier_cache_maint_common(data, start, size: chunk_size,
210 UNIPHIER_SSCOQM_S_RANGE | operation);
211
212 start += chunk_size;
213 size -= chunk_size;
214 }
215
216 __uniphier_cache_sync(data);
217}
218
219static void __uniphier_cache_enable(struct uniphier_cache_data *data, bool on)
220{
221 u32 val = 0;
222
223 if (on)
224 val = UNIPHIER_SSCC_WTG | UNIPHIER_SSCC_PRD | UNIPHIER_SSCC_ON;
225
226 writel_relaxed(val, data->ctrl_base + UNIPHIER_SSCC);
227}
228
229static void __init __uniphier_cache_set_active_ways(
230 struct uniphier_cache_data *data)
231{
232 unsigned int cpu;
233
234 for_each_possible_cpu(cpu)
235 writel_relaxed(data->way_mask, data->way_ctrl_base + 4 * cpu);
236}
237
238static void uniphier_cache_maint_range(unsigned long start, unsigned long end,
239 u32 operation)
240{
241 struct uniphier_cache_data *data;
242
243 list_for_each_entry(data, &uniphier_cache_list, list)
244 __uniphier_cache_maint_range(data, start, end, operation);
245}
246
247static void uniphier_cache_maint_all(u32 operation)
248{
249 struct uniphier_cache_data *data;
250
251 list_for_each_entry(data, &uniphier_cache_list, list)
252 __uniphier_cache_maint_all(data, operation);
253}
254
255static void uniphier_cache_inv_range(unsigned long start, unsigned long end)
256{
257 uniphier_cache_maint_range(start, end, UNIPHIER_SSCOQM_CM_INV);
258}
259
260static void uniphier_cache_clean_range(unsigned long start, unsigned long end)
261{
262 uniphier_cache_maint_range(start, end, UNIPHIER_SSCOQM_CM_CLEAN);
263}
264
265static void uniphier_cache_flush_range(unsigned long start, unsigned long end)
266{
267 uniphier_cache_maint_range(start, end, UNIPHIER_SSCOQM_CM_FLUSH);
268}
269
270static void __init uniphier_cache_inv_all(void)
271{
272 uniphier_cache_maint_all(UNIPHIER_SSCOQM_CM_INV);
273}
274
275static void uniphier_cache_flush_all(void)
276{
277 uniphier_cache_maint_all(UNIPHIER_SSCOQM_CM_FLUSH);
278}
279
280static void uniphier_cache_disable(void)
281{
282 struct uniphier_cache_data *data;
283
284 list_for_each_entry_reverse(data, &uniphier_cache_list, list)
285 __uniphier_cache_enable(data, on: false);
286
287 uniphier_cache_flush_all();
288}
289
290static void __init uniphier_cache_enable(void)
291{
292 struct uniphier_cache_data *data;
293
294 uniphier_cache_inv_all();
295
296 list_for_each_entry(data, &uniphier_cache_list, list) {
297 __uniphier_cache_enable(data, on: true);
298 __uniphier_cache_set_active_ways(data);
299 }
300}
301
302static void uniphier_cache_sync(void)
303{
304 struct uniphier_cache_data *data;
305
306 list_for_each_entry(data, &uniphier_cache_list, list)
307 __uniphier_cache_sync(data);
308}
309
310static const struct of_device_id uniphier_cache_match[] __initconst = {
311 { .compatible = "socionext,uniphier-system-cache" },
312 { /* sentinel */ }
313};
314
315static int __init __uniphier_cache_init(struct device_node *np,
316 unsigned int *cache_level)
317{
318 struct uniphier_cache_data *data;
319 u32 level, cache_size;
320 struct device_node *next_np;
321 int ret = 0;
322
323 if (!of_match_node(matches: uniphier_cache_match, node: np)) {
324 pr_err("L%d: not compatible with uniphier cache\n",
325 *cache_level);
326 return -EINVAL;
327 }
328
329 if (of_property_read_u32(np, propname: "cache-level", out_value: &level)) {
330 pr_err("L%d: cache-level is not specified\n", *cache_level);
331 return -EINVAL;
332 }
333
334 if (level != *cache_level) {
335 pr_err("L%d: cache-level is unexpected value %d\n",
336 *cache_level, level);
337 return -EINVAL;
338 }
339
340 if (!of_property_read_bool(np, propname: "cache-unified")) {
341 pr_err("L%d: cache-unified is not specified\n", *cache_level);
342 return -EINVAL;
343 }
344
345 data = kzalloc(size: sizeof(*data), GFP_KERNEL);
346 if (!data)
347 return -ENOMEM;
348
349 if (of_property_read_u32(np, propname: "cache-line-size", out_value: &data->line_size) ||
350 !is_power_of_2(n: data->line_size)) {
351 pr_err("L%d: cache-line-size is unspecified or invalid\n",
352 *cache_level);
353 ret = -EINVAL;
354 goto err;
355 }
356
357 if (of_property_read_u32(np, propname: "cache-sets", out_value: &data->nsets) ||
358 !is_power_of_2(n: data->nsets)) {
359 pr_err("L%d: cache-sets is unspecified or invalid\n",
360 *cache_level);
361 ret = -EINVAL;
362 goto err;
363 }
364
365 if (of_property_read_u32(np, propname: "cache-size", out_value: &cache_size) ||
366 cache_size == 0 || cache_size % (data->nsets * data->line_size)) {
367 pr_err("L%d: cache-size is unspecified or invalid\n",
368 *cache_level);
369 ret = -EINVAL;
370 goto err;
371 }
372
373 data->way_mask = GENMASK(cache_size / data->nsets / data->line_size - 1,
374 0);
375
376 data->ctrl_base = of_iomap(node: np, index: 0);
377 if (!data->ctrl_base) {
378 pr_err("L%d: failed to map control register\n", *cache_level);
379 ret = -ENOMEM;
380 goto err;
381 }
382
383 data->rev_base = of_iomap(node: np, index: 1);
384 if (!data->rev_base) {
385 pr_err("L%d: failed to map revision register\n", *cache_level);
386 ret = -ENOMEM;
387 goto err;
388 }
389
390 data->op_base = of_iomap(node: np, index: 2);
391 if (!data->op_base) {
392 pr_err("L%d: failed to map operation register\n", *cache_level);
393 ret = -ENOMEM;
394 goto err;
395 }
396
397 data->way_ctrl_base = data->ctrl_base + 0xc00;
398
399 if (*cache_level == 2) {
400 u32 revision = readl(addr: data->rev_base + UNIPHIER_SSCID);
401 /*
402 * The size of range operation is limited to (1 << 22) or less
403 * for PH-sLD8 or older SoCs.
404 */
405 if (revision <= 0x16)
406 data->range_op_max_size = (u32)1 << 22;
407
408 /*
409 * Unfortunatly, the offset address of active way control base
410 * varies from SoC to SoC.
411 */
412 switch (revision) {
413 case 0x11: /* sLD3 */
414 data->way_ctrl_base = data->ctrl_base + 0x870;
415 break;
416 case 0x12: /* LD4 */
417 case 0x16: /* sld8 */
418 data->way_ctrl_base = data->ctrl_base + 0x840;
419 break;
420 default:
421 break;
422 }
423 }
424
425 data->range_op_max_size -= data->line_size;
426
427 INIT_LIST_HEAD(list: &data->list);
428 list_add_tail(new: &data->list, head: &uniphier_cache_list); /* no mutex */
429
430 /*
431 * OK, this level has been successfully initialized. Look for the next
432 * level cache. Do not roll back even if the initialization of the
433 * next level cache fails because we want to continue with available
434 * cache levels.
435 */
436 next_np = of_find_next_cache_node(np);
437 if (next_np) {
438 (*cache_level)++;
439 ret = __uniphier_cache_init(np: next_np, cache_level);
440 }
441 of_node_put(node: next_np);
442
443 return ret;
444err:
445 iounmap(addr: data->op_base);
446 iounmap(addr: data->rev_base);
447 iounmap(addr: data->ctrl_base);
448 kfree(objp: data);
449
450 return ret;
451}
452
453int __init uniphier_cache_init(void)
454{
455 struct device_node *np = NULL;
456 unsigned int cache_level;
457 int ret = 0;
458
459 /* look for level 2 cache */
460 while ((np = of_find_matching_node(from: np, matches: uniphier_cache_match)))
461 if (!of_property_read_u32(np, propname: "cache-level", out_value: &cache_level) &&
462 cache_level == 2)
463 break;
464
465 if (!np)
466 return -ENODEV;
467
468 ret = __uniphier_cache_init(np, cache_level: &cache_level);
469 of_node_put(node: np);
470
471 if (ret) {
472 /*
473 * Error out iif L2 initialization fails. Continue with any
474 * error on L3 or outer because they are optional.
475 */
476 if (cache_level == 2) {
477 pr_err("failed to initialize L2 cache\n");
478 return ret;
479 }
480
481 cache_level--;
482 ret = 0;
483 }
484
485 outer_cache.inv_range = uniphier_cache_inv_range;
486 outer_cache.clean_range = uniphier_cache_clean_range;
487 outer_cache.flush_range = uniphier_cache_flush_range;
488 outer_cache.flush_all = uniphier_cache_flush_all;
489 outer_cache.disable = uniphier_cache_disable;
490 outer_cache.sync = uniphier_cache_sync;
491
492 uniphier_cache_enable();
493
494 pr_info("enabled outer cache (cache level: %d)\n", cache_level);
495
496 return ret;
497}
498

source code of linux/arch/arm/mm/cache-uniphier.c