1	// SPDX-License-Identifier: GPL-2.0+
2	//
3	// em28xx-cards.c - driver for Empia EM2800/EM2820/2840 USB
4	// video capture devices
5	//
6	// Copyright (C) 2005 Ludovico Cavedon <cavedon@sssup.it>
7	// Markus Rechberger <mrechberger@gmail.com>
8	// Mauro Carvalho Chehab <mchehab@kernel.org>
9	// Sascha Sommer <saschasommer@freenet.de>
10	// Copyright (C) 2012 Frank Schäfer <fschaefer.oss@googlemail.com>
11
12	#include "em28xx.h"
13
14	#include <linux/init.h>
15	#include <linux/module.h>
16	#include <linux/slab.h>
17	#include <linux/delay.h>
18	#include <linux/i2c.h>
19	#include <linux/usb.h>
20	#include <media/tuner.h>
21	#include <media/drv-intf/msp3400.h>
22	#include <media/i2c/saa7115.h>
23	#include <dt-bindings/media/tvp5150.h>
24	#include <media/i2c/tvaudio.h>
25	#include <media/tveeprom.h>
26	#include <media/v4l2-common.h>
27	#include <sound/ac97_codec.h>
28
29	#define DRIVER_NAME "em28xx"
30
31	static int tuner = -1;
32	module_param(tuner, int, 0444);
33	MODULE_PARM_DESC(tuner, "tuner type");
34
35	static unsigned int disable_ir;
36	module_param(disable_ir, int, 0444);
37	MODULE_PARM_DESC(disable_ir, "disable infrared remote support");
38
39	static unsigned int disable_usb_speed_check;
40	module_param(disable_usb_speed_check, int, 0444);
41	MODULE_PARM_DESC(disable_usb_speed_check,
42	"override min bandwidth requirement of 480M bps");
43
44	static unsigned int card[] = {[0 ... (EM28XX_MAXBOARDS - 1)] = -1U };
45	module_param_array(card, int, NULL, 0444);
46	MODULE_PARM_DESC(card, "card type");
47
48	static int usb_xfer_mode = -1;
49	module_param(usb_xfer_mode, int, 0444);
50	MODULE_PARM_DESC(usb_xfer_mode,
51	"USB transfer mode for frame data (-1 = auto, 0 = prefer isoc, 1 = prefer bulk)");
52
53	/* Bitmask marking allocated devices from 0 to EM28XX_MAXBOARDS - 1 */
54	static DECLARE_BITMAP(em28xx_devused, EM28XX_MAXBOARDS);
55
56	struct em28xx_hash_table {
57	unsigned long hash;
58	unsigned int model;
59	unsigned int tuner;
60	};
61
62	static void em28xx_pre_card_setup(struct em28xx *dev);
63
64	/*
65	* Reset sequences for analog/digital modes
66	*/
67
68	/* Reset for the most [analog] boards */
69	static const struct em28xx_reg_seq default_analog[] = {
70	{EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
71	{ -1, -1, -1, -1},
72	};
73
74	/* Reset for the most [digital] boards */
75	static const struct em28xx_reg_seq default_digital[] = {
76	{EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
77	{ -1, -1, -1, -1},
78	};
79
80	/* Board :Zolid Hybrid Tv Stick */
81	static struct em28xx_reg_seq zolid_tuner[] = {
82	{EM2820_R08_GPIO_CTRL, 0xfd, 0xff, 100},
83	{EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 100},
84	{ -1, -1, -1, -1},
85	};
86
87	static struct em28xx_reg_seq zolid_digital[] = {
88	{EM2820_R08_GPIO_CTRL, 0x6a, 0xff, 100},
89	{EM2820_R08_GPIO_CTRL, 0x7a, 0xff, 100},
90	{EM2880_R04_GPO, 0x04, 0xff, 100},
91	{EM2880_R04_GPO, 0x0c, 0xff, 100},
92	{ -1, -1, -1, -1},
93	};
94
95	/* Board Hauppauge WinTV HVR 900 analog */
96	static const struct em28xx_reg_seq hauppauge_wintv_hvr_900_analog[] = {
97	{EM2820_R08_GPIO_CTRL, 0x2d, ~EM_GPIO_4, 10},
98	{ 0x05, 0xff, 0x10, 10},
99	{ -1, -1, -1, -1},
100	};
101
102	/* Board Hauppauge WinTV HVR 900 digital */
103	static const struct em28xx_reg_seq hauppauge_wintv_hvr_900_digital[] = {
104	{EM2820_R08_GPIO_CTRL, 0x2e, ~EM_GPIO_4, 10},
105	{EM2880_R04_GPO, 0x04, 0x0f, 10},
106	{EM2880_R04_GPO, 0x0c, 0x0f, 10},
107	{ -1, -1, -1, -1},
108	};
109
110	/* Board Hauppauge WinTV HVR 900 (R2) digital */
111	static const struct em28xx_reg_seq hauppauge_wintv_hvr_900R2_digital[] = {
112	{EM2820_R08_GPIO_CTRL, 0x2e, ~EM_GPIO_4, 10},
113	{EM2880_R04_GPO, 0x0c, 0x0f, 10},
114	{ -1, -1, -1, -1},
115	};
116
117	/* Boards - EM2880 MSI DIGIVOX AD and EM2880_BOARD_MSI_DIGIVOX_AD_II */
118	static const struct em28xx_reg_seq em2880_msi_digivox_ad_analog[] = {
119	{EM2820_R08_GPIO_CTRL, 0x69, ~EM_GPIO_4, 10},
120	{ -1, -1, -1, -1},
121	};
122
123	/* Board - EM2882 Kworld 315U digital */
124	static const struct em28xx_reg_seq em2882_kworld_315u_digital[] = {
125	{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
126	{EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
127	{EM2880_R04_GPO, 0x04, 0xff, 10},
128	{EM2880_R04_GPO, 0x0c, 0xff, 10},
129	{EM2820_R08_GPIO_CTRL, 0x7e, 0xff, 10},
130	{ -1, -1, -1, -1},
131	};
132
133	static const struct em28xx_reg_seq em2882_kworld_315u_tuner_gpio[] = {
134	{EM2880_R04_GPO, 0x08, 0xff, 10},
135	{EM2880_R04_GPO, 0x0c, 0xff, 10},
136	{EM2880_R04_GPO, 0x08, 0xff, 10},
137	{EM2880_R04_GPO, 0x0c, 0xff, 10},
138	{ -1, -1, -1, -1},
139	};
140
141	static const struct em28xx_reg_seq kworld_330u_analog[] = {
142	{EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
143	{EM2880_R04_GPO, 0x00, 0xff, 10},
144	{ -1, -1, -1, -1},
145	};
146
147	static const struct em28xx_reg_seq kworld_330u_digital[] = {
148	{EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
149	{EM2880_R04_GPO, 0x08, 0xff, 10},
150	{ -1, -1, -1, -1},
151	};
152
153	/*
154	* Evga inDtube
155	* GPIO0 - Enable digital power (s5h1409) - low to enable
156	* GPIO1 - Enable analog power (tvp5150/emp202) - low to enable
157	* GPIO4 - xc3028 reset
158	* GOP3 - s5h1409 reset
159	*/
160	static const struct em28xx_reg_seq evga_indtube_analog[] = {
161	{EM2820_R08_GPIO_CTRL, 0x79, 0xff, 60},
162	{ -1, -1, -1, -1},
163	};
164
165	static const struct em28xx_reg_seq evga_indtube_digital[] = {
166	{EM2820_R08_GPIO_CTRL, 0x7a, 0xff, 1},
167	{EM2880_R04_GPO, 0x04, 0xff, 10},
168	{EM2880_R04_GPO, 0x0c, 0xff, 1},
169	{ -1, -1, -1, -1},
170	};
171
172	/*
173	* KWorld PlusTV 340U, UB435-Q and UB435-Q V2 (ATSC) GPIOs map:
174	* EM_GPIO_0 - currently unknown
175	* EM_GPIO_1 - LED disable/enable (1 = off, 0 = on)
176	* EM_GPIO_2 - currently unknown
177	* EM_GPIO_3 - currently unknown
178	* EM_GPIO_4 - TDA18271HD/C1 tuner (1 = active, 0 = in reset)
179	* EM_GPIO_5 - LGDT3304 ATSC/QAM demod (1 = active, 0 = in reset)
180	* EM_GPIO_6 - currently unknown
181	* EM_GPIO_7 - currently unknown
182	*/
183	static const struct em28xx_reg_seq kworld_a340_digital[] = {
184	{EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
185	{ -1, -1, -1, -1},
186	};
187
188	static const struct em28xx_reg_seq kworld_ub435q_v3_digital[] = {
189	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 100},
190	{EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 100},
191	{EM2874_R80_GPIO_P0_CTRL, 0xbe, 0xff, 100},
192	{EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 100},
193	{ -1, -1, -1, -1},
194	};
195
196	/* Pinnacle Hybrid Pro eb1a:2881 */
197	static const struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = {
198	{EM2820_R08_GPIO_CTRL, 0xfd, ~EM_GPIO_4, 10},
199	{ -1, -1, -1, -1},
200	};
201
202	static const struct em28xx_reg_seq pinnacle_hybrid_pro_digital[] = {
203	{EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
204	{EM2880_R04_GPO, 0x04, 0xff, 100},/* zl10353 reset */
205	{EM2880_R04_GPO, 0x0c, 0xff, 1},
206	{ -1, -1, -1, -1},
207	};
208
209	static const struct em28xx_reg_seq terratec_cinergy_USB_XS_FR_analog[] = {
210	{EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
211	{EM2880_R04_GPO, 0x00, 0xff, 10},
212	{ -1, -1, -1, -1},
213	};
214
215	static const struct em28xx_reg_seq terratec_cinergy_USB_XS_FR_digital[] = {
216	{EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
217	{EM2880_R04_GPO, 0x08, 0xff, 10},
218	{ -1, -1, -1, -1},
219	};
220
221	/*
222	* PCTV HD Mini (80e) GPIOs
223	* 0-5: not used
224	* 6: demod reset, active low
225	* 7: LED on, active high
226	*/
227	static const struct em28xx_reg_seq em2874_pctv_80e_digital[] = {
228	{EM28XX_R06_I2C_CLK, 0x45, 0xff, 10}, /*400 KHz*/
229	{EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 100},/*Demod reset*/
230	{EM2874_R80_GPIO_P0_CTRL, 0x40, 0xff, 10},
231	{ -1, -1, -1, -1},
232	};
233
234	/*
235	* eb1a:2868 Reddo DVB-C USB TV Box
236	* GPIO4 - CU1216L NIM
237	* Other GPIOs seems to be don't care.
238	*/
239	static const struct em28xx_reg_seq reddo_dvb_c_usb_box[] = {
240	{EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
241	{EM2820_R08_GPIO_CTRL, 0xde, 0xff, 10},
242	{EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
243	{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
244	{EM2820_R08_GPIO_CTRL, 0x7f, 0xff, 10},
245	{EM2820_R08_GPIO_CTRL, 0x6f, 0xff, 10},
246	{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
247	{ -1, -1, -1, -1},
248	};
249
250	/* Callback for the most boards */
251	static const struct em28xx_reg_seq default_tuner_gpio[] = {
252	{EM2820_R08_GPIO_CTRL, EM_GPIO_4, EM_GPIO_4, 10},
253	{EM2820_R08_GPIO_CTRL, 0, EM_GPIO_4, 10},
254	{EM2820_R08_GPIO_CTRL, EM_GPIO_4, EM_GPIO_4, 10},
255	{ -1, -1, -1, -1},
256	};
257
258	/* Mute/unmute */
259	static const struct em28xx_reg_seq compro_unmute_tv_gpio[] = {
260	{EM2820_R08_GPIO_CTRL, 5, 7, 10},
261	{ -1, -1, -1, -1},
262	};
263
264	static const struct em28xx_reg_seq compro_unmute_svid_gpio[] = {
265	{EM2820_R08_GPIO_CTRL, 4, 7, 10},
266	{ -1, -1, -1, -1},
267	};
268
269	static const struct em28xx_reg_seq compro_mute_gpio[] = {
270	{EM2820_R08_GPIO_CTRL, 6, 7, 10},
271	{ -1, -1, -1, -1},
272	};
273
274	/* Terratec AV350 */
275	static const struct em28xx_reg_seq terratec_av350_mute_gpio[] = {
276	{EM2820_R08_GPIO_CTRL, 0xff, 0x7f, 10},
277	{ -1, -1, -1, -1},
278	};
279
280	static const struct em28xx_reg_seq terratec_av350_unmute_gpio[] = {
281	{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
282	{ -1, -1, -1, -1},
283	};
284
285	static const struct em28xx_reg_seq silvercrest_reg_seq[] = {
286	{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
287	{EM2820_R08_GPIO_CTRL, 0x01, 0xf7, 10},
288	{ -1, -1, -1, -1},
289	};
290
291	static const struct em28xx_reg_seq vc211a_enable[] = {
292	{EM2820_R08_GPIO_CTRL, 0xff, 0x07, 10},
293	{EM2820_R08_GPIO_CTRL, 0xff, 0x0f, 10},
294	{EM2820_R08_GPIO_CTRL, 0xff, 0x0b, 10},
295	{ -1, -1, -1, -1},
296	};
297
298	static const struct em28xx_reg_seq dikom_dk300_digital[] = {
299	{EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
300	{EM2880_R04_GPO, 0x08, 0xff, 10},
301	{ -1, -1, -1, -1},
302	};
303
304	/* Reset for the most [digital] boards */
305	static const struct em28xx_reg_seq leadership_digital[] = {
306	{EM2874_R80_GPIO_P0_CTRL, 0x70, 0xff, 10},
307	{ -1, -1, -1, -1},
308	};
309
310	static const struct em28xx_reg_seq leadership_reset[] = {
311	{EM2874_R80_GPIO_P0_CTRL, 0xf0, 0xff, 10},
312	{EM2874_R80_GPIO_P0_CTRL, 0xb0, 0xff, 10},
313	{EM2874_R80_GPIO_P0_CTRL, 0xf0, 0xff, 10},
314	{ -1, -1, -1, -1},
315	};
316
317	/*
318	* 2013:024f PCTV nanoStick T2 290e
319	* GPIO_6 - demod reset
320	* GPIO_7 - LED
321	*/
322	static const struct em28xx_reg_seq pctv_290e[] = {
323	{EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 80},
324	{EM2874_R80_GPIO_P0_CTRL, 0x40, 0xff, 80}, /* GPIO_6 = 1 */
325	{EM2874_R80_GPIO_P0_CTRL, 0xc0, 0xff, 80}, /* GPIO_7 = 1 */
326	{ -1, -1, -1, -1},
327	};
328
329	#if 0
330	static const struct em28xx_reg_seq terratec_h5_gpio[] = {
331	{EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
332	{EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 100},
333	{EM2874_R80_GPIO_P0_CTRL, 0xf2, 0xff, 50},
334	{EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 50},
335	{ -1, -1, -1, -1},
336	};
337
338	static const struct em28xx_reg_seq terratec_h5_digital[] = {
339	{EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 10},
340	{EM2874_R80_GPIO_P0_CTRL, 0xe6, 0xff, 100},
341	{EM2874_R80_GPIO_P0_CTRL, 0xa6, 0xff, 10},
342	{ -1, -1, -1, -1},
343	};
344	#endif
345
346	/*
347	* 2013:024f PCTV DVB-S2 Stick 460e
348	* GPIO_0 - POWER_ON
349	* GPIO_1 - BOOST
350	* GPIO_2 - VUV_LNB (red LED)
351	* GPIO_3 - EXT_12V
352	* GPIO_4 - INT_DEM (DEMOD GPIO_0)
353	* GPIO_5 - INT_LNB
354	* GPIO_6 - RESET_DEM
355	* GPIO_7 - LED (green LED)
356	*/
357	static const struct em28xx_reg_seq pctv_460e[] = {
358	{EM2874_R80_GPIO_P0_CTRL, 0x01, 0xff, 50},
359	{ 0x0d, 0xff, 0xff, 50},
360	{EM2874_R80_GPIO_P0_CTRL, 0x41, 0xff, 50}, /* GPIO_6=1 */
361	{ 0x0d, 0x42, 0xff, 50},
362	{EM2874_R80_GPIO_P0_CTRL, 0x61, 0xff, 50}, /* GPIO_5=1 */
363	{ -1, -1, -1, -1},
364	};
365
366	static const struct em28xx_reg_seq c3tech_digital_duo_digital[] = {
367	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 10},
368	{EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 10}, /* xc5000 reset */
369	{EM2874_R80_GPIO_P0_CTRL, 0xf9, 0xff, 35},
370	{EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 10},
371	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 10},
372	{EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 10},
373	{EM2874_R80_GPIO_P0_CTRL, 0xbe, 0xff, 10},
374	{EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 20},
375	{ -1, -1, -1, -1},
376	};
377
378	/*
379	* 2013:0258 PCTV DVB-S2 Stick (461e)
380	* GPIO 0 = POWER_ON
381	* GPIO 1 = BOOST
382	* GPIO 2 = VUV_LNB (red LED)
383	* GPIO 3 = #EXT_12V
384	* GPIO 4 = INT_DEM
385	* GPIO 5 = INT_LNB
386	* GPIO 6 = #RESET_DEM
387	* GPIO 7 = P07_LED (green LED)
388	*/
389	static const struct em28xx_reg_seq pctv_461e[] = {
390	{EM2874_R80_GPIO_P0_CTRL, 0x7f, 0xff, 0},
391	{0x0d, 0xff, 0xff, 0},
392	{EM2874_R80_GPIO_P0_CTRL, 0x3f, 0xff, 100}, /* reset demod */
393	{EM2874_R80_GPIO_P0_CTRL, 0x7f, 0xff, 200}, /* reset demod */
394	{0x0d, 0x42, 0xff, 0},
395	{EM2874_R80_GPIO_P0_CTRL, 0xeb, 0xff, 0},
396	{EM2874_R5F_TS_ENABLE, 0x84, 0x84, 0}, /* parallel? | null discard */
397	{ -1, -1, -1, -1},
398	};
399
400	#if 0
401	static const struct em28xx_reg_seq hauppauge_930c_gpio[] = {
402	{EM2874_R80_GPIO_P0_CTRL, 0x6f, 0xff, 10},
403	{EM2874_R80_GPIO_P0_CTRL, 0x4f, 0xff, 10}, /* xc5000 reset */
404	{EM2874_R80_GPIO_P0_CTRL, 0x6f, 0xff, 10},
405	{EM2874_R80_GPIO_P0_CTRL, 0x4f, 0xff, 10},
406	{ -1, -1, -1, -1},
407	};
408
409	static const struct em28xx_reg_seq hauppauge_930c_digital[] = {
410	{EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 10},
411	{EM2874_R80_GPIO_P0_CTRL, 0xe6, 0xff, 100},
412	{EM2874_R80_GPIO_P0_CTRL, 0xa6, 0xff, 10},
413	{ -1, -1, -1, -1},
414	};
415	#endif
416
417	/*
418	* 1b80:e425 MaxMedia UB425-TC
419	* 1b80:e1cc Delock 61959
420	* GPIO_6 - demod reset, 0=active
421	* GPIO_7 - LED, 0=active
422	*/
423	static const struct em28xx_reg_seq maxmedia_ub425_tc[] = {
424	{EM2874_R80_GPIO_P0_CTRL, 0x83, 0xff, 100},
425	{EM2874_R80_GPIO_P0_CTRL, 0xc3, 0xff, 100}, /* GPIO_6 = 1 */
426	{EM2874_R80_GPIO_P0_CTRL, 0x43, 0xff, 000}, /* GPIO_7 = 0 */
427	{ -1, -1, -1, -1},
428	};
429
430	/*
431	* 2304:0242 PCTV QuatroStick (510e)
432	* GPIO_2: decoder reset, 0=active
433	* GPIO_4: decoder suspend, 0=active
434	* GPIO_6: demod reset, 0=active
435	* GPIO_7: LED, 1=active
436	*/
437	static const struct em28xx_reg_seq pctv_510e[] = {
438	{EM2874_R80_GPIO_P0_CTRL, 0x10, 0xff, 100},
439	{EM2874_R80_GPIO_P0_CTRL, 0x14, 0xff, 100}, /* GPIO_2 = 1 */
440	{EM2874_R80_GPIO_P0_CTRL, 0x54, 0xff, 050}, /* GPIO_6 = 1 */
441	{ -1, -1, -1, -1},
442	};
443
444	/*
445	* 2013:0251 PCTV QuatroStick nano (520e)
446	* GPIO_2: decoder reset, 0=active
447	* GPIO_4: decoder suspend, 0=active
448	* GPIO_6: demod reset, 0=active
449	* GPIO_7: LED, 1=active
450	*/
451	static const struct em28xx_reg_seq pctv_520e[] = {
452	{EM2874_R80_GPIO_P0_CTRL, 0x10, 0xff, 100},
453	{EM2874_R80_GPIO_P0_CTRL, 0x14, 0xff, 100}, /* GPIO_2 = 1 */
454	{EM2874_R80_GPIO_P0_CTRL, 0x54, 0xff, 050}, /* GPIO_6 = 1 */
455	{EM2874_R80_GPIO_P0_CTRL, 0xd4, 0xff, 000}, /* GPIO_7 = 1 */
456	{ -1, -1, -1, -1},
457	};
458
459	/*
460	* 1ae7:9003/9004 SpeedLink Vicious And Devine Laplace webcam
461	* reg 0x80/0x84:
462	* GPIO_0: capturing LED, 0=on, 1=off
463	* GPIO_2: AV mute button, 0=pressed, 1=unpressed
464	* GPIO 3: illumination button, 0=pressed, 1=unpressed
465	* GPIO_6: illumination/flash LED, 0=on, 1=off
466	* reg 0x81/0x85:
467	* GPIO_7: snapshot button, 0=pressed, 1=unpressed
468	*/
469	static const struct em28xx_reg_seq speedlink_vad_laplace_reg_seq[] = {
470	{EM2820_R08_GPIO_CTRL, 0xf7, 0xff, 10},
471	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xb2, 10},
472	{ -1, -1, -1, -1},
473	};
474
475	static const struct em28xx_reg_seq pctv_292e[] = {
476	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
477	{0x0d, 0xff, 0xff, 950},
478	{EM2874_R80_GPIO_P0_CTRL, 0xbd, 0xff, 100},
479	{EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 410},
480	{EM2874_R80_GPIO_P0_CTRL, 0x7d, 0xff, 300},
481	{EM2874_R80_GPIO_P0_CTRL, 0x7c, 0xff, 60},
482	{0x0d, 0x42, 0xff, 50},
483	{EM2874_R5F_TS_ENABLE, 0x85, 0xff, 0},
484	{-1, -1, -1, -1},
485	};
486
487	static const struct em28xx_reg_seq terratec_t2_stick_hd[] = {
488	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
489	{0x0d, 0xff, 0xff, 600},
490	{EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 10},
491	{EM2874_R80_GPIO_P0_CTRL, 0xbc, 0xff, 100},
492	{EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 100},
493	{EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 300},
494	{EM2874_R80_GPIO_P0_CTRL, 0xf8, 0xff, 100},
495	{EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 300},
496	{0x0d, 0x42, 0xff, 1000},
497	{EM2874_R5F_TS_ENABLE, 0x85, 0xff, 0},
498	{-1, -1, -1, -1},
499	};
500
501	static const struct em28xx_reg_seq plex_px_bcud[] = {
502	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
503	{0x0d, 0xff, 0xff, 0},
504	{EM2874_R50_IR_CONFIG, 0x01, 0xff, 0},
505	{EM28XX_R06_I2C_CLK, 0x40, 0xff, 0},
506	{EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 100},
507	{EM28XX_R12_VINENABLE, 0x20, 0x20, 0},
508	{0x0d, 0x42, 0xff, 1000},
509	{EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 10},
510	{EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 10},
511	{0x73, 0xfd, 0xff, 100},
512	{-1, -1, -1, -1},
513	};
514
515	/*
516	* 2040:0265 Hauppauge WinTV-dualHD DVB Isoc
517	* 2040:8265 Hauppauge WinTV-dualHD DVB Bulk
518	* 2040:026d Hauppauge WinTV-dualHD ATSC/QAM Isoc
519	* 2040:826d Hauppauge WinTV-dualHD ATSC/QAM Bulk
520	* reg 0x80/0x84:
521	* GPIO_0: Yellow LED tuner 1, 0=on, 1=off
522	* GPIO_1: Green LED tuner 1, 0=on, 1=off
523	* GPIO_2: Yellow LED tuner 2, 0=on, 1=off
524	* GPIO_3: Green LED tuner 2, 0=on, 1=off
525	* GPIO_5: Reset #2, 0=active
526	* GPIO_6: Reset #1, 0=active
527	*/
528	static const struct em28xx_reg_seq hauppauge_dualhd_dvb[] = {
529	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
530	{0x0d, 0xff, 0xff, 200},
531	{0x50, 0x04, 0xff, 300},
532	{EM2874_R80_GPIO_P0_CTRL, 0xbf, 0xff, 100}, /* demod 1 reset */
533	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 100},
534	{EM2874_R80_GPIO_P0_CTRL, 0xdf, 0xff, 100}, /* demod 2 reset */
535	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 100},
536	{EM2874_R5F_TS_ENABLE, 0x00, 0xff, 50}, /* disable TS filters */
537	{EM2874_R5D_TS1_PKT_SIZE, 0x05, 0xff, 50},
538	{EM2874_R5E_TS2_PKT_SIZE, 0x05, 0xff, 50},
539	{-1, -1, -1, -1},
540	};
541
542	/* Hauppauge USB QuadHD */
543	static struct em28xx_reg_seq hauppauge_usb_quadhd_atsc_reg_seq[] = {
544	{EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
545	{0x0d, 0xff, 0xff, 200},
546	{0x50, 0x04, 0xff, 300},
547	{EM2874_R80_GPIO_P0_CTRL, 0xb0, 0xf0, 100}, /* demod 1 reset */
548	{EM2874_R80_GPIO_P0_CTRL, 0xf0, 0xf0, 100},
549	{EM2874_R80_GPIO_P0_CTRL, 0xd0, 0xf0, 100}, /* demod 2 reset */
550	{EM2874_R80_GPIO_P0_CTRL, 0xf0, 0xf0, 100},
551	{EM2874_R5F_TS_ENABLE, 0x44, 0xff, 50},
552	{EM2874_R5D_TS1_PKT_SIZE, 0x05, 0xff, 50},
553	{EM2874_R5E_TS2_PKT_SIZE, 0x05, 0xff, 50},
554	{-1, -1, -1, -1},
555	};
556
557	/*
558	* Button definitions
559	*/
560	static const struct em28xx_button std_snapshot_button[] = {
561	{
562	.role = EM28XX_BUTTON_SNAPSHOT,
563	.reg_r = EM28XX_R0C_USBSUSP,
564	.reg_clearing = EM28XX_R0C_USBSUSP,
565	.mask = EM28XX_R0C_USBSUSP_SNAPSHOT,
566	.inverted = 0,
567	},
568	{-1, 0, 0, 0, 0},
569	};
570
571	static const struct em28xx_button speedlink_vad_laplace_buttons[] = {
572	{
573	.role = EM28XX_BUTTON_SNAPSHOT,
574	.reg_r = EM2874_R85_GPIO_P1_STATE,
575	.mask = 0x80,
576	.inverted = 1,
577	},
578	{
579	.role = EM28XX_BUTTON_ILLUMINATION,
580	.reg_r = EM2874_R84_GPIO_P0_STATE,
581	.mask = 0x08,
582	.inverted = 1,
583	},
584	{-1, 0, 0, 0, 0},
585	};
586
587	/*
588	* LED definitions
589	*/
590	static struct em28xx_led speedlink_vad_laplace_leds[] = {
591	{
592	.role = EM28XX_LED_ANALOG_CAPTURING,
593	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
594	.gpio_mask = 0x01,
595	.inverted = 1,
596	},
597	{
598	.role = EM28XX_LED_ILLUMINATION,
599	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
600	.gpio_mask = 0x40,
601	.inverted = 1,
602	},
603	{-1, 0, 0, 0},
604	};
605
606	static struct em28xx_led kworld_ub435q_v3_leds[] = {
607	{
608	.role = EM28XX_LED_DIGITAL_CAPTURING,
609	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
610	.gpio_mask = 0x80,
611	.inverted = 1,
612	},
613	{-1, 0, 0, 0},
614	};
615
616	static struct em28xx_led pctv_80e_leds[] = {
617	{
618	.role = EM28XX_LED_DIGITAL_CAPTURING,
619	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
620	.gpio_mask = 0x80,
621	.inverted = 0,
622	},
623	{-1, 0, 0, 0},
624	};
625
626	static struct em28xx_led terratec_grabby_leds[] = {
627	{
628	.role = EM28XX_LED_ANALOG_CAPTURING,
629	.gpio_reg = EM2820_R08_GPIO_CTRL,
630	.gpio_mask = EM_GPIO_3,
631	.inverted = 1,
632	},
633	{-1, 0, 0, 0},
634	};
635
636	static struct em28xx_led hauppauge_dualhd_leds[] = {
637	{
638	.role = EM28XX_LED_DIGITAL_CAPTURING,
639	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
640	.gpio_mask = EM_GPIO_1,
641	.inverted = 1,
642	},
643	{
644	.role = EM28XX_LED_DIGITAL_CAPTURING_TS2,
645	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
646	.gpio_mask = EM_GPIO_3,
647	.inverted = 1,
648	},
649	{-1, 0, 0, 0},
650	};
651
652	static struct em28xx_led hauppauge_usb_quadhd_leds[] = {
653	{
654	.role = EM28XX_LED_DIGITAL_CAPTURING,
655	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
656	.gpio_mask = EM_GPIO_2,
657	.inverted = 1,
658	},
659	{
660	.role = EM28XX_LED_DIGITAL_CAPTURING_TS2,
661	.gpio_reg = EM2874_R80_GPIO_P0_CTRL,
662	.gpio_mask = EM_GPIO_0,
663	.inverted = 1,
664	},
665	{-1, 0, 0, 0},
666	};
667
668	/*
669	* Board definitions
670	*/
671	const struct em28xx_board em28xx_boards[] = {
672	[EM2750_BOARD_UNKNOWN] = {
673	.name = "EM2710/EM2750/EM2751 webcam grabber",
674	.xclk = EM28XX_XCLK_FREQUENCY_20MHZ,
675	.tuner_type = TUNER_ABSENT,
676	.is_webcam = 1,
677	.input = { {
678	.type = EM28XX_VMUX_COMPOSITE,
679	.vmux = 0,
680	.amux = EM28XX_AMUX_VIDEO,
681	.gpio = silvercrest_reg_seq,
682	} },
683	},
684	[EM2800_BOARD_UNKNOWN] = {
685	.name = "Unknown EM2800 video grabber",
686	.is_em2800 = 1,
687	.tda9887_conf = TDA9887_PRESENT,
688	.decoder = EM28XX_SAA711X,
689	.tuner_type = TUNER_ABSENT,
690	.input = { {
691	.type = EM28XX_VMUX_COMPOSITE,
692	.vmux = SAA7115_COMPOSITE0,
693	.amux = EM28XX_AMUX_LINE_IN,
694	}, {
695	.type = EM28XX_VMUX_SVIDEO,
696	.vmux = SAA7115_SVIDEO3,
697	.amux = EM28XX_AMUX_LINE_IN,
698	} },
699	},
700	[EM2820_BOARD_UNKNOWN] = {
701	.name = "Unknown EM2750/28xx video grabber",
702	.tuner_type = TUNER_ABSENT,
703	.is_webcam = 1, /* To enable sensor probe */
704	},
705	[EM2882_BOARD_ZOLID_HYBRID_TV_STICK] = {
706	.name = ":ZOLID HYBRID TV STICK",
707	.tuner_type = TUNER_XC2028,
708	.tuner_gpio = zolid_tuner,
709	.decoder = EM28XX_TVP5150,
710	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
711	.mts_firmware = 1,
712	.has_dvb = 1,
713	.dvb_gpio = zolid_digital,
714	},
715	[EM2750_BOARD_DLCW_130] = {
716	/* Beijing Huaqi Information Digital Technology Co., Ltd */
717	.name = "Huaqi DLCW-130",
718	.valid = EM28XX_BOARD_NOT_VALIDATED,
719	.xclk = EM28XX_XCLK_FREQUENCY_48MHZ,
720	.tuner_type = TUNER_ABSENT,
721	.is_webcam = 1,
722	.input = { {
723	.type = EM28XX_VMUX_COMPOSITE,
724	.vmux = 0,
725	.amux = EM28XX_AMUX_VIDEO,
726	} },
727	},
728	[EM2820_BOARD_KWORLD_PVRTV2800RF] = {
729	.name = "Kworld PVR TV 2800 RF",
730	.tuner_type = TUNER_TEMIC_PAL,
731	.tda9887_conf = TDA9887_PRESENT,
732	.decoder = EM28XX_SAA711X,
733	.input = { {
734	.type = EM28XX_VMUX_COMPOSITE,
735	.vmux = SAA7115_COMPOSITE0,
736	.amux = EM28XX_AMUX_LINE_IN,
737	}, {
738	.type = EM28XX_VMUX_SVIDEO,
739	.vmux = SAA7115_SVIDEO3,
740	.amux = EM28XX_AMUX_LINE_IN,
741	} },
742	},
743	[EM2820_BOARD_GADMEI_TVR200] = {
744	.name = "Gadmei TVR200",
745	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
746	.tda9887_conf = TDA9887_PRESENT,
747	.decoder = EM28XX_SAA711X,
748	.input = { {
749	.type = EM28XX_VMUX_TELEVISION,
750	.vmux = SAA7115_COMPOSITE2,
751	.amux = EM28XX_AMUX_LINE_IN,
752	}, {
753	.type = EM28XX_VMUX_COMPOSITE,
754	.vmux = SAA7115_COMPOSITE0,
755	.amux = EM28XX_AMUX_LINE_IN,
756	}, {
757	.type = EM28XX_VMUX_SVIDEO,
758	.vmux = SAA7115_SVIDEO3,
759	.amux = EM28XX_AMUX_LINE_IN,
760	} },
761	},
762	[EM2820_BOARD_TERRATEC_CINERGY_250] = {
763	.name = "Terratec Cinergy 250 USB",
764	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
765	.has_ir_i2c = 1,
766	.tda9887_conf = TDA9887_PRESENT,
767	.decoder = EM28XX_SAA711X,
768	.input = { {
769	.type = EM28XX_VMUX_TELEVISION,
770	.vmux = SAA7115_COMPOSITE2,
771	.amux = EM28XX_AMUX_VIDEO,
772	}, {
773	.type = EM28XX_VMUX_COMPOSITE,
774	.vmux = SAA7115_COMPOSITE0,
775	.amux = EM28XX_AMUX_LINE_IN,
776	}, {
777	.type = EM28XX_VMUX_SVIDEO,
778	.vmux = SAA7115_SVIDEO3,
779	.amux = EM28XX_AMUX_LINE_IN,
780	} },
781	},
782	[EM2820_BOARD_PINNACLE_USB_2] = {
783	.name = "Pinnacle PCTV USB 2",
784	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
785	.has_ir_i2c = 1,
786	.tda9887_conf = TDA9887_PRESENT,
787	.decoder = EM28XX_SAA711X,
788	.input = { {
789	.type = EM28XX_VMUX_TELEVISION,
790	.vmux = SAA7115_COMPOSITE2,
791	.amux = EM28XX_AMUX_VIDEO,
792	}, {
793	.type = EM28XX_VMUX_COMPOSITE,
794	.vmux = SAA7115_COMPOSITE0,
795	.amux = EM28XX_AMUX_LINE_IN,
796	}, {
797	.type = EM28XX_VMUX_SVIDEO,
798	.vmux = SAA7115_SVIDEO3,
799	.amux = EM28XX_AMUX_LINE_IN,
800	} },
801	},
802	[EM2820_BOARD_HAUPPAUGE_WINTV_USB_2] = {
803	.name = "Hauppauge WinTV USB 2",
804	.tuner_type = TUNER_PHILIPS_FM1236_MK3,
805	.tda9887_conf = TDA9887_PRESENT |
806	TDA9887_PORT1_ACTIVE |
807	TDA9887_PORT2_ACTIVE,
808	.decoder = EM28XX_TVP5150,
809	.has_msp34xx = 1,
810	.has_ir_i2c = 1,
811	.input = { {
812	.type = EM28XX_VMUX_TELEVISION,
813	.vmux = TVP5150_COMPOSITE0,
814	.amux = MSP_INPUT_DEFAULT,
815	}, {
816	.type = EM28XX_VMUX_SVIDEO,
817	.vmux = TVP5150_SVIDEO,
818	.amux = MSP_INPUT(MSP_IN_SCART1, MSP_IN_TUNER1,
819	MSP_DSP_IN_SCART, MSP_DSP_IN_SCART),
820	} },
821	},
822	[EM2820_BOARD_DLINK_USB_TV] = {
823	.name = "D-Link DUB-T210 TV Tuner",
824	.valid = EM28XX_BOARD_NOT_VALIDATED,
825	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
826	.tda9887_conf = TDA9887_PRESENT,
827	.decoder = EM28XX_SAA711X,
828	.input = { {
829	.type = EM28XX_VMUX_TELEVISION,
830	.vmux = SAA7115_COMPOSITE2,
831	.amux = EM28XX_AMUX_LINE_IN,
832	}, {
833	.type = EM28XX_VMUX_COMPOSITE,
834	.vmux = SAA7115_COMPOSITE0,
835	.amux = EM28XX_AMUX_LINE_IN,
836	}, {
837	.type = EM28XX_VMUX_SVIDEO,
838	.vmux = SAA7115_SVIDEO3,
839	.amux = EM28XX_AMUX_LINE_IN,
840	} },
841	},
842	[EM2820_BOARD_HERCULES_SMART_TV_USB2] = {
843	.name = "Hercules Smart TV USB 2.0",
844	.valid = EM28XX_BOARD_NOT_VALIDATED,
845	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
846	.tda9887_conf = TDA9887_PRESENT,
847	.decoder = EM28XX_SAA711X,
848	.input = { {
849	.type = EM28XX_VMUX_TELEVISION,
850	.vmux = SAA7115_COMPOSITE2,
851	.amux = EM28XX_AMUX_LINE_IN,
852	}, {
853	.type = EM28XX_VMUX_COMPOSITE,
854	.vmux = SAA7115_COMPOSITE0,
855	.amux = EM28XX_AMUX_LINE_IN,
856	}, {
857	.type = EM28XX_VMUX_SVIDEO,
858	.vmux = SAA7115_SVIDEO3,
859	.amux = EM28XX_AMUX_LINE_IN,
860	} },
861	},
862	[EM2820_BOARD_PINNACLE_USB_2_FM1216ME] = {
863	.name = "Pinnacle PCTV USB 2 (Philips FM1216ME)",
864	.valid = EM28XX_BOARD_NOT_VALIDATED,
865	.tuner_type = TUNER_PHILIPS_FM1216ME_MK3,
866	.tda9887_conf = TDA9887_PRESENT,
867	.decoder = EM28XX_SAA711X,
868	.input = { {
869	.type = EM28XX_VMUX_TELEVISION,
870	.vmux = SAA7115_COMPOSITE2,
871	.amux = EM28XX_AMUX_VIDEO,
872	}, {
873	.type = EM28XX_VMUX_COMPOSITE,
874	.vmux = SAA7115_COMPOSITE0,
875	.amux = EM28XX_AMUX_LINE_IN,
876	}, {
877	.type = EM28XX_VMUX_SVIDEO,
878	.vmux = SAA7115_SVIDEO3,
879	.amux = EM28XX_AMUX_LINE_IN,
880	} },
881	},
882	[EM2820_BOARD_GADMEI_UTV310] = {
883	.name = "Gadmei UTV310",
884	.valid = EM28XX_BOARD_NOT_VALIDATED,
885	.tuner_type = TUNER_TNF_5335MF,
886	.tda9887_conf = TDA9887_PRESENT,
887	.decoder = EM28XX_SAA711X,
888	.input = { {
889	.type = EM28XX_VMUX_TELEVISION,
890	.vmux = SAA7115_COMPOSITE1,
891	.amux = EM28XX_AMUX_LINE_IN,
892	}, {
893	.type = EM28XX_VMUX_COMPOSITE,
894	.vmux = SAA7115_COMPOSITE0,
895	.amux = EM28XX_AMUX_LINE_IN,
896	}, {
897	.type = EM28XX_VMUX_SVIDEO,
898	.vmux = SAA7115_SVIDEO3,
899	.amux = EM28XX_AMUX_LINE_IN,
900	} },
901	},
902	[EM2820_BOARD_LEADTEK_WINFAST_USBII_DELUXE] = {
903	.name = "Leadtek Winfast USB II Deluxe",
904	.valid = EM28XX_BOARD_NOT_VALIDATED,
905	.tuner_type = TUNER_PHILIPS_FM1216ME_MK3,
906	.has_ir_i2c = 1,
907	.tvaudio_addr = 0x58,
908	.tda9887_conf = TDA9887_PRESENT |
909	TDA9887_PORT2_ACTIVE |
910	TDA9887_QSS,
911	.decoder = EM28XX_SAA711X,
912	.adecoder = EM28XX_TVAUDIO,
913	.input = { {
914	.type = EM28XX_VMUX_TELEVISION,
915	.vmux = SAA7115_COMPOSITE4,
916	.amux = EM28XX_AMUX_AUX,
917	}, {
918	.type = EM28XX_VMUX_COMPOSITE,
919	.vmux = SAA7115_COMPOSITE5,
920	.amux = EM28XX_AMUX_LINE_IN,
921	}, {
922	.type = EM28XX_VMUX_SVIDEO,
923	.vmux = SAA7115_SVIDEO3,
924	.amux = EM28XX_AMUX_LINE_IN,
925	} },
926	.radio = {
927	.type = EM28XX_RADIO,
928	.amux = EM28XX_AMUX_AUX,
929	}
930	},
931	[EM2820_BOARD_VIDEOLOGY_20K14XUSB] = {
932	.name = "Videology 20K14XUSB USB2.0",
933	.valid = EM28XX_BOARD_NOT_VALIDATED,
934	.tuner_type = TUNER_ABSENT,
935	.is_webcam = 1,
936	.input = { {
937	.type = EM28XX_VMUX_COMPOSITE,
938	.vmux = 0,
939	.amux = EM28XX_AMUX_VIDEO,
940	} },
941	},
942	[EM2820_BOARD_SILVERCREST_WEBCAM] = {
943	.name = "Silvercrest Webcam 1.3mpix",
944	.tuner_type = TUNER_ABSENT,
945	.is_webcam = 1,
946	.input = { {
947	.type = EM28XX_VMUX_COMPOSITE,
948	.vmux = 0,
949	.amux = EM28XX_AMUX_VIDEO,
950	.gpio = silvercrest_reg_seq,
951	} },
952	},
953	[EM2821_BOARD_SUPERCOMP_USB_2] = {
954	.name = "Supercomp USB 2.0 TV",
955	.valid = EM28XX_BOARD_NOT_VALIDATED,
956	.tuner_type = TUNER_PHILIPS_FM1236_MK3,
957	.tda9887_conf = TDA9887_PRESENT |
958	TDA9887_PORT1_ACTIVE |
959	TDA9887_PORT2_ACTIVE,
960	.decoder = EM28XX_SAA711X,
961	.input = { {
962	.type = EM28XX_VMUX_TELEVISION,
963	.vmux = SAA7115_COMPOSITE2,
964	.amux = EM28XX_AMUX_LINE_IN,
965	}, {
966	.type = EM28XX_VMUX_COMPOSITE,
967	.vmux = SAA7115_COMPOSITE0,
968	.amux = EM28XX_AMUX_VIDEO,
969	}, {
970	.type = EM28XX_VMUX_SVIDEO,
971	.vmux = SAA7115_SVIDEO3,
972	.amux = EM28XX_AMUX_LINE_IN,
973	} },
974	},
975	[EM2821_BOARD_USBGEAR_VD204] = {
976	.name = "Usbgear VD204v9",
977	.valid = EM28XX_BOARD_NOT_VALIDATED,
978	.tuner_type = TUNER_ABSENT, /* Capture only device */
979	.decoder = EM28XX_SAA711X,
980	.input = { {
981	.type = EM28XX_VMUX_COMPOSITE,
982	.vmux = SAA7115_COMPOSITE0,
983	.amux = EM28XX_AMUX_LINE_IN,
984	}, {
985	.type = EM28XX_VMUX_SVIDEO,
986	.vmux = SAA7115_SVIDEO3,
987	.amux = EM28XX_AMUX_LINE_IN,
988	} },
989	},
990	[EM2860_BOARD_NETGMBH_CAM] = {
991	/* Beijing Huaqi Information Digital Technology Co., Ltd */
992	.name = "NetGMBH Cam",
993	.valid = EM28XX_BOARD_NOT_VALIDATED,
994	.tuner_type = TUNER_ABSENT,
995	.is_webcam = 1,
996	.input = { {
997	.type = EM28XX_VMUX_COMPOSITE,
998	.vmux = 0,
999	.amux = EM28XX_AMUX_VIDEO,
1000	} },
1001	},
1002	[EM2860_BOARD_TYPHOON_DVD_MAKER] = {
1003	.name = "Typhoon DVD Maker",
1004	.decoder = EM28XX_SAA711X,
1005	.tuner_type = TUNER_ABSENT, /* Capture only device */
1006	.input = { {
1007	.type = EM28XX_VMUX_COMPOSITE,
1008	.vmux = SAA7115_COMPOSITE0,
1009	.amux = EM28XX_AMUX_LINE_IN,
1010	}, {
1011	.type = EM28XX_VMUX_SVIDEO,
1012	.vmux = SAA7115_SVIDEO3,
1013	.amux = EM28XX_AMUX_LINE_IN,
1014	} },
1015	},
1016	[EM2860_BOARD_GADMEI_UTV330] = {
1017	.name = "Gadmei UTV330",
1018	.valid = EM28XX_BOARD_NOT_VALIDATED,
1019	.tuner_type = TUNER_TNF_5335MF,
1020	.tda9887_conf = TDA9887_PRESENT,
1021	.decoder = EM28XX_SAA711X,
1022	.input = { {
1023	.type = EM28XX_VMUX_TELEVISION,
1024	.vmux = SAA7115_COMPOSITE2,
1025	.amux = EM28XX_AMUX_VIDEO,
1026	}, {
1027	.type = EM28XX_VMUX_COMPOSITE,
1028	.vmux = SAA7115_COMPOSITE0,
1029	.amux = EM28XX_AMUX_LINE_IN,
1030	}, {
1031	.type = EM28XX_VMUX_SVIDEO,
1032	.vmux = SAA7115_SVIDEO3,
1033	.amux = EM28XX_AMUX_LINE_IN,
1034	} },
1035	},
1036	[EM2861_BOARD_GADMEI_UTV330PLUS] = {
1037	.name = "Gadmei UTV330+",
1038	.tuner_type = TUNER_TNF_5335MF,
1039	.tda9887_conf = TDA9887_PRESENT,
1040	.ir_codes = RC_MAP_GADMEI_RM008Z,
1041	.decoder = EM28XX_SAA711X,
1042	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1043	.input = { {
1044	.type = EM28XX_VMUX_TELEVISION,
1045	.vmux = SAA7115_COMPOSITE2,
1046	.amux = EM28XX_AMUX_VIDEO,
1047	}, {
1048	.type = EM28XX_VMUX_COMPOSITE,
1049	.vmux = SAA7115_COMPOSITE0,
1050	.amux = EM28XX_AMUX_LINE_IN,
1051	}, {
1052	.type = EM28XX_VMUX_SVIDEO,
1053	.vmux = SAA7115_SVIDEO3,
1054	.amux = EM28XX_AMUX_LINE_IN,
1055	} },
1056	},
1057	[EM2860_BOARD_TERRATEC_HYBRID_XS] = {
1058	.name = "Terratec Cinergy A Hybrid XS",
1059	.valid = EM28XX_BOARD_NOT_VALIDATED,
1060	.tuner_type = TUNER_XC2028,
1061	.tuner_gpio = default_tuner_gpio,
1062	.decoder = EM28XX_TVP5150,
1063
1064	.input = { {
1065	.type = EM28XX_VMUX_TELEVISION,
1066	.vmux = TVP5150_COMPOSITE0,
1067	.amux = EM28XX_AMUX_VIDEO,
1068	.gpio = hauppauge_wintv_hvr_900_analog,
1069	}, {
1070	.type = EM28XX_VMUX_COMPOSITE,
1071	.vmux = TVP5150_COMPOSITE1,
1072	.amux = EM28XX_AMUX_LINE_IN,
1073	.gpio = hauppauge_wintv_hvr_900_analog,
1074	}, {
1075	.type = EM28XX_VMUX_SVIDEO,
1076	.vmux = TVP5150_SVIDEO,
1077	.amux = EM28XX_AMUX_LINE_IN,
1078	.gpio = hauppauge_wintv_hvr_900_analog,
1079	} },
1080	},
1081	[EM2861_BOARD_KWORLD_PVRTV_300U] = {
1082	.name = "KWorld PVRTV 300U",
1083	.valid = EM28XX_BOARD_NOT_VALIDATED,
1084	.tuner_type = TUNER_XC2028,
1085	.tuner_gpio = default_tuner_gpio,
1086	.decoder = EM28XX_TVP5150,
1087	.input = { {
1088	.type = EM28XX_VMUX_TELEVISION,
1089	.vmux = TVP5150_COMPOSITE0,
1090	.amux = EM28XX_AMUX_VIDEO,
1091	}, {
1092	.type = EM28XX_VMUX_COMPOSITE,
1093	.vmux = TVP5150_COMPOSITE1,
1094	.amux = EM28XX_AMUX_LINE_IN,
1095	}, {
1096	.type = EM28XX_VMUX_SVIDEO,
1097	.vmux = TVP5150_SVIDEO,
1098	.amux = EM28XX_AMUX_LINE_IN,
1099	} },
1100	},
1101	[EM2861_BOARD_YAKUMO_MOVIE_MIXER] = {
1102	.name = "Yakumo MovieMixer",
1103	.tuner_type = TUNER_ABSENT, /* Capture only device */
1104	.decoder = EM28XX_TVP5150,
1105	.input = { {
1106	.type = EM28XX_VMUX_TELEVISION,
1107	.vmux = TVP5150_COMPOSITE0,
1108	.amux = EM28XX_AMUX_VIDEO,
1109	}, {
1110	.type = EM28XX_VMUX_COMPOSITE,
1111	.vmux = TVP5150_COMPOSITE1,
1112	.amux = EM28XX_AMUX_LINE_IN,
1113	}, {
1114	.type = EM28XX_VMUX_SVIDEO,
1115	.vmux = TVP5150_SVIDEO,
1116	.amux = EM28XX_AMUX_LINE_IN,
1117	} },
1118	},
1119	[EM2860_BOARD_TVP5150_REFERENCE_DESIGN] = {
1120	.name = "EM2860/TVP5150 Reference Design",
1121	.tuner_type = TUNER_ABSENT, /* Capture only device */
1122	.decoder = EM28XX_TVP5150,
1123	.input = { {
1124	.type = EM28XX_VMUX_COMPOSITE,
1125	.vmux = TVP5150_COMPOSITE1,
1126	.amux = EM28XX_AMUX_LINE_IN,
1127	}, {
1128	.type = EM28XX_VMUX_SVIDEO,
1129	.vmux = TVP5150_SVIDEO,
1130	.amux = EM28XX_AMUX_LINE_IN,
1131	} },
1132	},
1133	[EM2861_BOARD_PLEXTOR_PX_TV100U] = {
1134	.name = "Plextor ConvertX PX-TV100U",
1135	.tuner_type = TUNER_TNF_5335MF,
1136	.xclk = EM28XX_XCLK_I2S_MSB_TIMING |
1137	EM28XX_XCLK_FREQUENCY_12MHZ,
1138	.tda9887_conf = TDA9887_PRESENT,
1139	.decoder = EM28XX_TVP5150,
1140	.has_msp34xx = 1,
1141	.input = { {
1142	.type = EM28XX_VMUX_TELEVISION,
1143	.vmux = TVP5150_COMPOSITE0,
1144	.amux = EM28XX_AMUX_LINE_IN,
1145	.gpio = pinnacle_hybrid_pro_analog,
1146	}, {
1147	.type = EM28XX_VMUX_COMPOSITE,
1148	.vmux = TVP5150_COMPOSITE1,
1149	.amux = EM28XX_AMUX_LINE_IN,
1150	.gpio = pinnacle_hybrid_pro_analog,
1151	}, {
1152	.type = EM28XX_VMUX_SVIDEO,
1153	.vmux = TVP5150_SVIDEO,
1154	.amux = EM28XX_AMUX_LINE_IN,
1155	.gpio = pinnacle_hybrid_pro_analog,
1156	} },
1157	},
1158
1159	/* Those boards with em2870 are DVB Only*/
1160
1161	[EM2870_BOARD_TERRATEC_XS] = {
1162	.name = "Terratec Cinergy T XS",
1163	.valid = EM28XX_BOARD_NOT_VALIDATED,
1164	.tuner_type = TUNER_XC2028,
1165	.tuner_gpio = default_tuner_gpio,
1166	},
1167	[EM2870_BOARD_TERRATEC_XS_MT2060] = {
1168	.name = "Terratec Cinergy T XS (MT2060)",
1169	.xclk = EM28XX_XCLK_IR_RC5_MODE |
1170	EM28XX_XCLK_FREQUENCY_12MHZ,
1171	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
1172	.tuner_type = TUNER_ABSENT, /* MT2060 */
1173	.has_dvb = 1,
1174	.tuner_gpio = default_tuner_gpio,
1175	},
1176	[EM2870_BOARD_KWORLD_350U] = {
1177	.name = "Kworld 350 U DVB-T",
1178	.valid = EM28XX_BOARD_NOT_VALIDATED,
1179	.tuner_type = TUNER_XC2028,
1180	.tuner_gpio = default_tuner_gpio,
1181	},
1182	[EM2870_BOARD_KWORLD_355U] = {
1183	.name = "Kworld 355 U DVB-T",
1184	.valid = EM28XX_BOARD_NOT_VALIDATED,
1185	.tuner_type = TUNER_ABSENT,
1186	.tuner_gpio = default_tuner_gpio,
1187	.has_dvb = 1,
1188	.dvb_gpio = default_digital,
1189	},
1190	[EM2870_BOARD_PINNACLE_PCTV_DVB] = {
1191	.name = "Pinnacle PCTV DVB-T",
1192	.valid = EM28XX_BOARD_NOT_VALIDATED,
1193	.tuner_type = TUNER_ABSENT, /* MT2060 */
1194	/* djh - I have serious doubts this is right... */
1195	.xclk = EM28XX_XCLK_IR_RC5_MODE |
1196	EM28XX_XCLK_FREQUENCY_10MHZ,
1197	},
1198	[EM2870_BOARD_COMPRO_VIDEOMATE] = {
1199	.name = "Compro, VideoMate U3",
1200	.valid = EM28XX_BOARD_NOT_VALIDATED,
1201	.tuner_type = TUNER_ABSENT, /* MT2060 */
1202	},
1203
1204	[EM2880_BOARD_TERRATEC_HYBRID_XS_FR] = {
1205	.name = "Terratec Hybrid XS Secam",
1206	.has_msp34xx = 1,
1207	.tuner_type = TUNER_XC2028,
1208	.tuner_gpio = default_tuner_gpio,
1209	.decoder = EM28XX_TVP5150,
1210	.has_dvb = 1,
1211	.dvb_gpio = terratec_cinergy_USB_XS_FR_digital,
1212	.input = { {
1213	.type = EM28XX_VMUX_TELEVISION,
1214	.vmux = TVP5150_COMPOSITE0,
1215	.amux = EM28XX_AMUX_VIDEO,
1216	.gpio = terratec_cinergy_USB_XS_FR_analog,
1217	}, {
1218	.type = EM28XX_VMUX_COMPOSITE,
1219	.vmux = TVP5150_COMPOSITE1,
1220	.amux = EM28XX_AMUX_LINE_IN,
1221	.gpio = terratec_cinergy_USB_XS_FR_analog,
1222	}, {
1223	.type = EM28XX_VMUX_SVIDEO,
1224	.vmux = TVP5150_SVIDEO,
1225	.amux = EM28XX_AMUX_LINE_IN,
1226	.gpio = terratec_cinergy_USB_XS_FR_analog,
1227	} },
1228	},
1229	[EM2884_BOARD_TERRATEC_H5] = {
1230	.name = "Terratec Cinergy H5",
1231	.has_dvb = 1,
1232	#if 0
1233	.tuner_type = TUNER_PHILIPS_TDA8290,
1234	.tuner_addr = 0x41,
1235	.dvb_gpio = terratec_h5_digital, /* FIXME: probably wrong */
1236	.tuner_gpio = terratec_h5_gpio,
1237	#else
1238	.tuner_type = TUNER_ABSENT,
1239	#endif
1240	.def_i2c_bus = 1,
1241	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1242	EM28XX_I2C_FREQ_400_KHZ,
1243	},
1244	[EM2884_BOARD_TERRATEC_H6] = {
1245	.name = "Terratec Cinergy H6 rev. 2",
1246	.has_dvb = 1,
1247	.ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
1248	#if 0
1249	.tuner_type = TUNER_PHILIPS_TDA8290,
1250	.tuner_addr = 0x41,
1251	.dvb_gpio = terratec_h5_digital, /* FIXME: probably wrong */
1252	.tuner_gpio = terratec_h5_gpio,
1253	#else
1254	.tuner_type = TUNER_ABSENT,
1255	#endif
1256	.def_i2c_bus = 1,
1257	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1258	EM28XX_I2C_FREQ_400_KHZ,
1259	},
1260	[EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C] = {
1261	.name = "Hauppauge WinTV HVR 930C",
1262	.has_dvb = 1,
1263	#if 0 /* FIXME: Add analog support */
1264	.tuner_type = TUNER_XC5000,
1265	.tuner_addr = 0x41,
1266	.dvb_gpio = hauppauge_930c_digital,
1267	.tuner_gpio = hauppauge_930c_gpio,
1268	#else
1269	.tuner_type = TUNER_ABSENT,
1270	#endif
1271	.ir_codes = RC_MAP_HAUPPAUGE,
1272	.def_i2c_bus = 1,
1273	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1274	EM28XX_I2C_FREQ_400_KHZ,
1275	},
1276	[EM2884_BOARD_C3TECH_DIGITAL_DUO] = {
1277	.name = "C3 Tech Digital Duo HDTV/SDTV USB",
1278	.has_dvb = 1,
1279	/* FIXME: Add analog support - need a saa7136 driver */
1280	.tuner_type = TUNER_ABSENT, /* Digital-only TDA18271HD */
1281	.ir_codes = RC_MAP_EMPTY,
1282	.def_i2c_bus = 1,
1283	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
1284	.dvb_gpio = c3tech_digital_duo_digital,
1285	},
1286	[EM2884_BOARD_CINERGY_HTC_STICK] = {
1287	.name = "Terratec Cinergy HTC Stick",
1288	.has_dvb = 1,
1289	.ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
1290	.tuner_type = TUNER_ABSENT,
1291	.def_i2c_bus = 1,
1292	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1293	EM28XX_I2C_FREQ_400_KHZ,
1294	},
1295	[EM2884_BOARD_ELGATO_EYETV_HYBRID_2008] = {
1296	.name = "Elgato EyeTV Hybrid 2008 INT",
1297	.has_dvb = 1,
1298	.ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
1299	.tuner_type = TUNER_ABSENT,
1300	.def_i2c_bus = 1,
1301	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1302	EM28XX_I2C_FREQ_400_KHZ,
1303	},
1304	[EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900] = {
1305	.name = "Hauppauge WinTV HVR 900",
1306	.tda9887_conf = TDA9887_PRESENT,
1307	.tuner_type = TUNER_XC2028,
1308	.tuner_gpio = default_tuner_gpio,
1309	.mts_firmware = 1,
1310	.has_dvb = 1,
1311	.dvb_gpio = hauppauge_wintv_hvr_900_digital,
1312	.ir_codes = RC_MAP_HAUPPAUGE,
1313	.decoder = EM28XX_TVP5150,
1314	.input = { {
1315	.type = EM28XX_VMUX_TELEVISION,
1316	.vmux = TVP5150_COMPOSITE0,
1317	.amux = EM28XX_AMUX_VIDEO,
1318	.gpio = hauppauge_wintv_hvr_900_analog,
1319	}, {
1320	.type = EM28XX_VMUX_COMPOSITE,
1321	.vmux = TVP5150_COMPOSITE1,
1322	.amux = EM28XX_AMUX_LINE_IN,
1323	.gpio = hauppauge_wintv_hvr_900_analog,
1324	}, {
1325	.type = EM28XX_VMUX_SVIDEO,
1326	.vmux = TVP5150_SVIDEO,
1327	.amux = EM28XX_AMUX_LINE_IN,
1328	.gpio = hauppauge_wintv_hvr_900_analog,
1329	} },
1330	},
1331	[EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2] = {
1332	.name = "Hauppauge WinTV HVR 900 (R2)",
1333	.tda9887_conf = TDA9887_PRESENT,
1334	.tuner_type = TUNER_XC2028,
1335	.tuner_gpio = default_tuner_gpio,
1336	.mts_firmware = 1,
1337	.has_dvb = 1,
1338	.dvb_gpio = hauppauge_wintv_hvr_900R2_digital,
1339	.ir_codes = RC_MAP_HAUPPAUGE,
1340	.decoder = EM28XX_TVP5150,
1341	.input = { {
1342	.type = EM28XX_VMUX_TELEVISION,
1343	.vmux = TVP5150_COMPOSITE0,
1344	.amux = EM28XX_AMUX_VIDEO,
1345	.gpio = hauppauge_wintv_hvr_900_analog,
1346	}, {
1347	.type = EM28XX_VMUX_COMPOSITE,
1348	.vmux = TVP5150_COMPOSITE1,
1349	.amux = EM28XX_AMUX_LINE_IN,
1350	.gpio = hauppauge_wintv_hvr_900_analog,
1351	}, {
1352	.type = EM28XX_VMUX_SVIDEO,
1353	.vmux = TVP5150_SVIDEO,
1354	.amux = EM28XX_AMUX_LINE_IN,
1355	.gpio = hauppauge_wintv_hvr_900_analog,
1356	} },
1357	},
1358	[EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850] = {
1359	.name = "Hauppauge WinTV HVR 850",
1360	.tuner_type = TUNER_XC2028,
1361	.tuner_gpio = default_tuner_gpio,
1362	.mts_firmware = 1,
1363	.has_dvb = 1,
1364	.dvb_gpio = hauppauge_wintv_hvr_900_digital,
1365	.ir_codes = RC_MAP_HAUPPAUGE,
1366	.decoder = EM28XX_TVP5150,
1367	.input = { {
1368	.type = EM28XX_VMUX_TELEVISION,
1369	.vmux = TVP5150_COMPOSITE0,
1370	.amux = EM28XX_AMUX_VIDEO,
1371	.gpio = hauppauge_wintv_hvr_900_analog,
1372	}, {
1373	.type = EM28XX_VMUX_COMPOSITE,
1374	.vmux = TVP5150_COMPOSITE1,
1375	.amux = EM28XX_AMUX_LINE_IN,
1376	.gpio = hauppauge_wintv_hvr_900_analog,
1377	}, {
1378	.type = EM28XX_VMUX_SVIDEO,
1379	.vmux = TVP5150_SVIDEO,
1380	.amux = EM28XX_AMUX_LINE_IN,
1381	.gpio = hauppauge_wintv_hvr_900_analog,
1382	} },
1383	},
1384	[EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950] = {
1385	.name = "Hauppauge WinTV HVR 950",
1386	.tuner_type = TUNER_XC2028,
1387	.tuner_gpio = default_tuner_gpio,
1388	.mts_firmware = 1,
1389	.has_dvb = 1,
1390	.dvb_gpio = hauppauge_wintv_hvr_900_digital,
1391	.ir_codes = RC_MAP_HAUPPAUGE,
1392	.decoder = EM28XX_TVP5150,
1393	.input = { {
1394	.type = EM28XX_VMUX_TELEVISION,
1395	.vmux = TVP5150_COMPOSITE0,
1396	.amux = EM28XX_AMUX_VIDEO,
1397	.gpio = hauppauge_wintv_hvr_900_analog,
1398	}, {
1399	.type = EM28XX_VMUX_COMPOSITE,
1400	.vmux = TVP5150_COMPOSITE1,
1401	.amux = EM28XX_AMUX_LINE_IN,
1402	.gpio = hauppauge_wintv_hvr_900_analog,
1403	}, {
1404	.type = EM28XX_VMUX_SVIDEO,
1405	.vmux = TVP5150_SVIDEO,
1406	.amux = EM28XX_AMUX_LINE_IN,
1407	.gpio = hauppauge_wintv_hvr_900_analog,
1408	} },
1409	},
1410	[EM2880_BOARD_PINNACLE_PCTV_HD_PRO] = {
1411	.name = "Pinnacle PCTV HD Pro Stick",
1412	.tuner_type = TUNER_XC2028,
1413	.tuner_gpio = default_tuner_gpio,
1414	.mts_firmware = 1,
1415	.has_dvb = 1,
1416	.dvb_gpio = hauppauge_wintv_hvr_900_digital,
1417	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
1418	.decoder = EM28XX_TVP5150,
1419	.input = { {
1420	.type = EM28XX_VMUX_TELEVISION,
1421	.vmux = TVP5150_COMPOSITE0,
1422	.amux = EM28XX_AMUX_VIDEO,
1423	.gpio = hauppauge_wintv_hvr_900_analog,
1424	}, {
1425	.type = EM28XX_VMUX_COMPOSITE,
1426	.vmux = TVP5150_COMPOSITE1,
1427	.amux = EM28XX_AMUX_LINE_IN,
1428	.gpio = hauppauge_wintv_hvr_900_analog,
1429	}, {
1430	.type = EM28XX_VMUX_SVIDEO,
1431	.vmux = TVP5150_SVIDEO,
1432	.amux = EM28XX_AMUX_LINE_IN,
1433	.gpio = hauppauge_wintv_hvr_900_analog,
1434	} },
1435	},
1436	[EM2880_BOARD_AMD_ATI_TV_WONDER_HD_600] = {
1437	.name = "AMD ATI TV Wonder HD 600",
1438	.tuner_type = TUNER_XC2028,
1439	.tuner_gpio = default_tuner_gpio,
1440	.mts_firmware = 1,
1441	.has_dvb = 1,
1442	.dvb_gpio = hauppauge_wintv_hvr_900_digital,
1443	.ir_codes = RC_MAP_ATI_TV_WONDER_HD_600,
1444	.decoder = EM28XX_TVP5150,
1445	.input = { {
1446	.type = EM28XX_VMUX_TELEVISION,
1447	.vmux = TVP5150_COMPOSITE0,
1448	.amux = EM28XX_AMUX_VIDEO,
1449	.gpio = hauppauge_wintv_hvr_900_analog,
1450	}, {
1451	.type = EM28XX_VMUX_COMPOSITE,
1452	.vmux = TVP5150_COMPOSITE1,
1453	.amux = EM28XX_AMUX_LINE_IN,
1454	.gpio = hauppauge_wintv_hvr_900_analog,
1455	}, {
1456	.type = EM28XX_VMUX_SVIDEO,
1457	.vmux = TVP5150_SVIDEO,
1458	.amux = EM28XX_AMUX_LINE_IN,
1459	.gpio = hauppauge_wintv_hvr_900_analog,
1460	} },
1461	},
1462	[EM2880_BOARD_TERRATEC_HYBRID_XS] = {
1463	.name = "Terratec Hybrid XS",
1464	.tuner_type = TUNER_XC2028,
1465	.tuner_gpio = default_tuner_gpio,
1466	.decoder = EM28XX_TVP5150,
1467	.has_dvb = 1,
1468	.dvb_gpio = default_digital,
1469	.ir_codes = RC_MAP_TERRATEC_CINERGY_XS,
1470	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ, /* NEC IR */
1471	.input = { {
1472	.type = EM28XX_VMUX_TELEVISION,
1473	.vmux = TVP5150_COMPOSITE0,
1474	.amux = EM28XX_AMUX_VIDEO,
1475	.gpio = default_analog,
1476	}, {
1477	.type = EM28XX_VMUX_COMPOSITE,
1478	.vmux = TVP5150_COMPOSITE1,
1479	.amux = EM28XX_AMUX_LINE_IN,
1480	.gpio = default_analog,
1481	}, {
1482	.type = EM28XX_VMUX_SVIDEO,
1483	.vmux = TVP5150_SVIDEO,
1484	.amux = EM28XX_AMUX_LINE_IN,
1485	.gpio = default_analog,
1486	} },
1487	},
1488	/*
1489	* maybe there's a reason behind it why Terratec sells the Hybrid XS
1490	* as Prodigy XS with a different PID, let's keep it separated for now
1491	* maybe we'll need it later on
1492	*/
1493	[EM2880_BOARD_TERRATEC_PRODIGY_XS] = {
1494	.name = "Terratec Prodigy XS",
1495	.tuner_type = TUNER_XC2028,
1496	.tuner_gpio = default_tuner_gpio,
1497	.decoder = EM28XX_TVP5150,
1498	.input = { {
1499	.type = EM28XX_VMUX_TELEVISION,
1500	.vmux = TVP5150_COMPOSITE0,
1501	.amux = EM28XX_AMUX_VIDEO,
1502	.gpio = hauppauge_wintv_hvr_900_analog,
1503	}, {
1504	.type = EM28XX_VMUX_COMPOSITE,
1505	.vmux = TVP5150_COMPOSITE1,
1506	.amux = EM28XX_AMUX_LINE_IN,
1507	.gpio = hauppauge_wintv_hvr_900_analog,
1508	}, {
1509	.type = EM28XX_VMUX_SVIDEO,
1510	.vmux = TVP5150_SVIDEO,
1511	.amux = EM28XX_AMUX_LINE_IN,
1512	.gpio = hauppauge_wintv_hvr_900_analog,
1513	} },
1514	},
1515	[EM2820_BOARD_MSI_VOX_USB_2] = {
1516	.name = "MSI VOX USB 2.0",
1517	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
1518	.tda9887_conf = TDA9887_PRESENT |
1519	TDA9887_PORT1_ACTIVE |
1520	TDA9887_PORT2_ACTIVE,
1521	.max_range_640_480 = 1,
1522	.decoder = EM28XX_SAA711X,
1523	.input = { {
1524	.type = EM28XX_VMUX_TELEVISION,
1525	.vmux = SAA7115_COMPOSITE4,
1526	.amux = EM28XX_AMUX_VIDEO,
1527	}, {
1528	.type = EM28XX_VMUX_COMPOSITE,
1529	.vmux = SAA7115_COMPOSITE0,
1530	.amux = EM28XX_AMUX_LINE_IN,
1531	}, {
1532	.type = EM28XX_VMUX_SVIDEO,
1533	.vmux = SAA7115_SVIDEO3,
1534	.amux = EM28XX_AMUX_LINE_IN,
1535	} },
1536	},
1537	[EM2800_BOARD_TERRATEC_CINERGY_200] = {
1538	.name = "Terratec Cinergy 200 USB",
1539	.is_em2800 = 1,
1540	.has_ir_i2c = 1,
1541	.tuner_type = TUNER_LG_TALN,
1542	.tda9887_conf = TDA9887_PRESENT,
1543	.decoder = EM28XX_SAA711X,
1544	.input = { {
1545	.type = EM28XX_VMUX_TELEVISION,
1546	.vmux = SAA7115_COMPOSITE2,
1547	.amux = EM28XX_AMUX_VIDEO,
1548	}, {
1549	.type = EM28XX_VMUX_COMPOSITE,
1550	.vmux = SAA7115_COMPOSITE0,
1551	.amux = EM28XX_AMUX_LINE_IN,
1552	}, {
1553	.type = EM28XX_VMUX_SVIDEO,
1554	.vmux = SAA7115_SVIDEO3,
1555	.amux = EM28XX_AMUX_LINE_IN,
1556	} },
1557	},
1558	[EM2800_BOARD_GRABBEEX_USB2800] = {
1559	.name = "eMPIA Technology, Inc. GrabBeeX+ Video Encoder",
1560	.is_em2800 = 1,
1561	.decoder = EM28XX_SAA711X,
1562	.tuner_type = TUNER_ABSENT, /* capture only board */
1563	.input = { {
1564	.type = EM28XX_VMUX_COMPOSITE,
1565	.vmux = SAA7115_COMPOSITE0,
1566	.amux = EM28XX_AMUX_LINE_IN,
1567	}, {
1568	.type = EM28XX_VMUX_SVIDEO,
1569	.vmux = SAA7115_SVIDEO3,
1570	.amux = EM28XX_AMUX_LINE_IN,
1571	} },
1572	},
1573	[EM2800_BOARD_VC211A] = {
1574	.name = "Actionmaster/LinXcel/Digitus VC211A",
1575	.is_em2800 = 1,
1576	.tuner_type = TUNER_ABSENT, /* Capture-only board */
1577	.decoder = EM28XX_SAA711X,
1578	.input = { {
1579	.type = EM28XX_VMUX_COMPOSITE,
1580	.vmux = SAA7115_COMPOSITE0,
1581	.amux = EM28XX_AMUX_LINE_IN,
1582	.gpio = vc211a_enable,
1583	}, {
1584	.type = EM28XX_VMUX_SVIDEO,
1585	.vmux = SAA7115_SVIDEO3,
1586	.amux = EM28XX_AMUX_LINE_IN,
1587	.gpio = vc211a_enable,
1588	} },
1589	},
1590	[EM2800_BOARD_LEADTEK_WINFAST_USBII] = {
1591	.name = "Leadtek Winfast USB II",
1592	.is_em2800 = 1,
1593	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
1594	.tda9887_conf = TDA9887_PRESENT,
1595	.decoder = EM28XX_SAA711X,
1596	.input = { {
1597	.type = EM28XX_VMUX_TELEVISION,
1598	.vmux = SAA7115_COMPOSITE2,
1599	.amux = EM28XX_AMUX_VIDEO,
1600	}, {
1601	.type = EM28XX_VMUX_COMPOSITE,
1602	.vmux = SAA7115_COMPOSITE0,
1603	.amux = EM28XX_AMUX_LINE_IN,
1604	}, {
1605	.type = EM28XX_VMUX_SVIDEO,
1606	.vmux = SAA7115_SVIDEO3,
1607	.amux = EM28XX_AMUX_LINE_IN,
1608	} },
1609	},
1610	[EM2800_BOARD_KWORLD_USB2800] = {
1611	.name = "Kworld USB2800",
1612	.is_em2800 = 1,
1613	.tuner_type = TUNER_PHILIPS_FCV1236D,
1614	.tda9887_conf = TDA9887_PRESENT,
1615	.decoder = EM28XX_SAA711X,
1616	.input = { {
1617	.type = EM28XX_VMUX_TELEVISION,
1618	.vmux = SAA7115_COMPOSITE2,
1619	.amux = EM28XX_AMUX_VIDEO,
1620	}, {
1621	.type = EM28XX_VMUX_COMPOSITE,
1622	.vmux = SAA7115_COMPOSITE0,
1623	.amux = EM28XX_AMUX_LINE_IN,
1624	}, {
1625	.type = EM28XX_VMUX_SVIDEO,
1626	.vmux = SAA7115_SVIDEO3,
1627	.amux = EM28XX_AMUX_LINE_IN,
1628	} },
1629	},
1630	[EM2820_BOARD_PINNACLE_DVC_90] = {
1631	.name = "Pinnacle Dazzle DVC 90/100/101/107 / Kaiser Baas Video to DVD maker / Kworld DVD Maker 2 / Plextor ConvertX PX-AV100U",
1632	.tuner_type = TUNER_ABSENT, /* capture only board */
1633	.decoder = EM28XX_SAA711X,
1634	.input = { {
1635	.type = EM28XX_VMUX_COMPOSITE,
1636	.vmux = SAA7115_COMPOSITE0,
1637	.amux = EM28XX_AMUX_LINE_IN,
1638	}, {
1639	.type = EM28XX_VMUX_SVIDEO,
1640	.vmux = SAA7115_SVIDEO3,
1641	.amux = EM28XX_AMUX_LINE_IN,
1642	} },
1643	},
1644	[EM2800_BOARD_VGEAR_POCKETTV] = {
1645	.name = "V-Gear PocketTV",
1646	.is_em2800 = 1,
1647	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
1648	.tda9887_conf = TDA9887_PRESENT,
1649	.decoder = EM28XX_SAA711X,
1650	.input = { {
1651	.type = EM28XX_VMUX_TELEVISION,
1652	.vmux = SAA7115_COMPOSITE2,
1653	.amux = EM28XX_AMUX_VIDEO,
1654	}, {
1655	.type = EM28XX_VMUX_COMPOSITE,
1656	.vmux = SAA7115_COMPOSITE0,
1657	.amux = EM28XX_AMUX_LINE_IN,
1658	}, {
1659	.type = EM28XX_VMUX_SVIDEO,
1660	.vmux = SAA7115_SVIDEO3,
1661	.amux = EM28XX_AMUX_LINE_IN,
1662	} },
1663	},
1664	[EM2820_BOARD_PROLINK_PLAYTV_BOX4_USB2] = {
1665	.name = "Pixelview PlayTV Box 4 USB 2.0",
1666	.tda9887_conf = TDA9887_PRESENT,
1667	.tuner_type = TUNER_YMEC_TVF_5533MF,
1668	.decoder = EM28XX_SAA711X,
1669	.input = { {
1670	.type = EM28XX_VMUX_TELEVISION,
1671	.vmux = SAA7115_COMPOSITE2,
1672	.amux = EM28XX_AMUX_VIDEO,
1673	.aout = EM28XX_AOUT_MONO | /* I2S */
1674	EM28XX_AOUT_MASTER, /* Line out pin */
1675	}, {
1676	.type = EM28XX_VMUX_COMPOSITE,
1677	.vmux = SAA7115_COMPOSITE0,
1678	.amux = EM28XX_AMUX_LINE_IN,
1679	}, {
1680	.type = EM28XX_VMUX_SVIDEO,
1681	.vmux = SAA7115_SVIDEO3,
1682	.amux = EM28XX_AMUX_LINE_IN,
1683	} },
1684	},
1685	[EM2820_BOARD_PROLINK_PLAYTV_USB2] = {
1686	.name = "SIIG AVTuner-PVR / Pixelview Prolink PlayTV USB 2.0",
1687	.buttons = std_snapshot_button,
1688	.tda9887_conf = TDA9887_PRESENT,
1689	.tuner_type = TUNER_YMEC_TVF_5533MF,
1690	.tuner_addr = 0x60,
1691	.decoder = EM28XX_SAA711X,
1692	.input = { {
1693	.type = EM28XX_VMUX_TELEVISION,
1694	.vmux = SAA7115_COMPOSITE2,
1695	.amux = EM28XX_AMUX_VIDEO,
1696	.aout = EM28XX_AOUT_MONO | /* I2S */
1697	EM28XX_AOUT_MASTER, /* Line out pin */
1698	}, {
1699	.type = EM28XX_VMUX_COMPOSITE,
1700	.vmux = SAA7115_COMPOSITE0,
1701	.amux = EM28XX_AMUX_LINE_IN,
1702	}, {
1703	.type = EM28XX_VMUX_SVIDEO,
1704	.vmux = SAA7115_SVIDEO3,
1705	.amux = EM28XX_AMUX_LINE_IN,
1706	} },
1707	},
1708	[EM2860_BOARD_SAA711X_REFERENCE_DESIGN] = {
1709	.name = "EM2860/SAA711X Reference Design",
1710	.buttons = std_snapshot_button,
1711	.tuner_type = TUNER_ABSENT,
1712	.decoder = EM28XX_SAA711X,
1713	.input = { {
1714	.type = EM28XX_VMUX_SVIDEO,
1715	.vmux = SAA7115_SVIDEO3,
1716	}, {
1717	.type = EM28XX_VMUX_COMPOSITE,
1718	.vmux = SAA7115_COMPOSITE0,
1719	} },
1720	},
1721
1722	[EM2874_BOARD_LEADERSHIP_ISDBT] = {
1723	.def_i2c_bus = 1,
1724	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1725	EM28XX_I2C_FREQ_100_KHZ,
1726	.xclk = EM28XX_XCLK_FREQUENCY_10MHZ,
1727	.name = "EM2874 Leadership ISDBT",
1728	.tuner_type = TUNER_ABSENT,
1729	.tuner_gpio = leadership_reset,
1730	.dvb_gpio = leadership_digital,
1731	.has_dvb = 1,
1732	},
1733
1734	[EM2880_BOARD_MSI_DIGIVOX_AD] = {
1735	.name = "MSI DigiVox A/D",
1736	.valid = EM28XX_BOARD_NOT_VALIDATED,
1737	.tuner_type = TUNER_XC2028,
1738	.tuner_gpio = default_tuner_gpio,
1739	.decoder = EM28XX_TVP5150,
1740	.input = { {
1741	.type = EM28XX_VMUX_TELEVISION,
1742	.vmux = TVP5150_COMPOSITE0,
1743	.amux = EM28XX_AMUX_VIDEO,
1744	.gpio = em2880_msi_digivox_ad_analog,
1745	}, {
1746	.type = EM28XX_VMUX_COMPOSITE,
1747	.vmux = TVP5150_COMPOSITE1,
1748	.amux = EM28XX_AMUX_LINE_IN,
1749	.gpio = em2880_msi_digivox_ad_analog,
1750	}, {
1751	.type = EM28XX_VMUX_SVIDEO,
1752	.vmux = TVP5150_SVIDEO,
1753	.amux = EM28XX_AMUX_LINE_IN,
1754	.gpio = em2880_msi_digivox_ad_analog,
1755	} },
1756	},
1757	[EM2880_BOARD_MSI_DIGIVOX_AD_II] = {
1758	.name = "MSI DigiVox A/D II",
1759	.valid = EM28XX_BOARD_NOT_VALIDATED,
1760	.tuner_type = TUNER_XC2028,
1761	.tuner_gpio = default_tuner_gpio,
1762	.decoder = EM28XX_TVP5150,
1763	.input = { {
1764	.type = EM28XX_VMUX_TELEVISION,
1765	.vmux = TVP5150_COMPOSITE0,
1766	.amux = EM28XX_AMUX_VIDEO,
1767	.gpio = em2880_msi_digivox_ad_analog,
1768	}, {
1769	.type = EM28XX_VMUX_COMPOSITE,
1770	.vmux = TVP5150_COMPOSITE1,
1771	.amux = EM28XX_AMUX_LINE_IN,
1772	.gpio = em2880_msi_digivox_ad_analog,
1773	}, {
1774	.type = EM28XX_VMUX_SVIDEO,
1775	.vmux = TVP5150_SVIDEO,
1776	.amux = EM28XX_AMUX_LINE_IN,
1777	.gpio = em2880_msi_digivox_ad_analog,
1778	} },
1779	},
1780	[EM2880_BOARD_KWORLD_DVB_305U] = {
1781	.name = "KWorld DVB-T 305U",
1782	.tuner_type = TUNER_XC2028,
1783	.tuner_gpio = default_tuner_gpio,
1784	.decoder = EM28XX_TVP5150,
1785	.input = { {
1786	.type = EM28XX_VMUX_TELEVISION,
1787	.vmux = TVP5150_COMPOSITE0,
1788	.amux = EM28XX_AMUX_VIDEO,
1789	}, {
1790	.type = EM28XX_VMUX_COMPOSITE,
1791	.vmux = TVP5150_COMPOSITE1,
1792	.amux = EM28XX_AMUX_LINE_IN,
1793	}, {
1794	.type = EM28XX_VMUX_SVIDEO,
1795	.vmux = TVP5150_SVIDEO,
1796	.amux = EM28XX_AMUX_LINE_IN,
1797	} },
1798	},
1799	[EM2880_BOARD_KWORLD_DVB_310U] = {
1800	.name = "KWorld DVB-T 310U",
1801	.tuner_type = TUNER_XC2028,
1802	.tuner_gpio = default_tuner_gpio,
1803	.has_dvb = 1,
1804	.dvb_gpio = default_digital,
1805	.mts_firmware = 1,
1806	.decoder = EM28XX_TVP5150,
1807	.input = { {
1808	.type = EM28XX_VMUX_TELEVISION,
1809	.vmux = TVP5150_COMPOSITE0,
1810	.amux = EM28XX_AMUX_VIDEO,
1811	.gpio = default_analog,
1812	}, {
1813	.type = EM28XX_VMUX_COMPOSITE,
1814	.vmux = TVP5150_COMPOSITE1,
1815	.amux = EM28XX_AMUX_LINE_IN,
1816	.gpio = default_analog,
1817	}, { /* S-video has not been tested yet */
1818	.type = EM28XX_VMUX_SVIDEO,
1819	.vmux = TVP5150_SVIDEO,
1820	.amux = EM28XX_AMUX_LINE_IN,
1821	.gpio = default_analog,
1822	} },
1823	},
1824	[EM2882_BOARD_KWORLD_ATSC_315U] = {
1825	.name = "KWorld ATSC 315U HDTV TV Box",
1826	.valid = EM28XX_BOARD_NOT_VALIDATED,
1827	.tuner_type = TUNER_THOMSON_DTT761X,
1828	.tuner_gpio = em2882_kworld_315u_tuner_gpio,
1829	.tda9887_conf = TDA9887_PRESENT,
1830	.decoder = EM28XX_SAA711X,
1831	.has_dvb = 1,
1832	.dvb_gpio = em2882_kworld_315u_digital,
1833	.ir_codes = RC_MAP_KWORLD_315U,
1834	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1835	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
1836	#if 0
1837	/* FIXME: Analog mode - still not ready */
1838	.input = { {
1839	.type = EM28XX_VMUX_TELEVISION,
1840	.vmux = SAA7115_COMPOSITE2,
1841	.amux = EM28XX_AMUX_VIDEO,
1842	.gpio = em2882_kworld_315u_analog,
1843	.aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
1844	}, {
1845	.type = EM28XX_VMUX_COMPOSITE,
1846	.vmux = SAA7115_COMPOSITE0,
1847	.amux = EM28XX_AMUX_LINE_IN,
1848	.gpio = em2882_kworld_315u_analog1,
1849	.aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
1850	}, {
1851	.type = EM28XX_VMUX_SVIDEO,
1852	.vmux = SAA7115_SVIDEO3,
1853	.amux = EM28XX_AMUX_LINE_IN,
1854	.gpio = em2882_kworld_315u_analog1,
1855	.aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
1856	} },
1857	#endif
1858	},
1859	[EM2880_BOARD_EMPIRE_DUAL_TV] = {
1860	.name = "Empire dual TV",
1861	.tuner_type = TUNER_XC2028,
1862	.tuner_gpio = default_tuner_gpio,
1863	.has_dvb = 1,
1864	.dvb_gpio = default_digital,
1865	.mts_firmware = 1,
1866	.decoder = EM28XX_TVP5150,
1867	.input = { {
1868	.type = EM28XX_VMUX_TELEVISION,
1869	.vmux = TVP5150_COMPOSITE0,
1870	.amux = EM28XX_AMUX_VIDEO,
1871	.gpio = default_analog,
1872	}, {
1873	.type = EM28XX_VMUX_COMPOSITE,
1874	.vmux = TVP5150_COMPOSITE1,
1875	.amux = EM28XX_AMUX_LINE_IN,
1876	.gpio = default_analog,
1877	}, {
1878	.type = EM28XX_VMUX_SVIDEO,
1879	.vmux = TVP5150_SVIDEO,
1880	.amux = EM28XX_AMUX_LINE_IN,
1881	.gpio = default_analog,
1882	} },
1883	},
1884	[EM2881_BOARD_DNT_DA2_HYBRID] = {
1885	.name = "DNT DA2 Hybrid",
1886	.valid = EM28XX_BOARD_NOT_VALIDATED,
1887	.tuner_type = TUNER_XC2028,
1888	.tuner_gpio = default_tuner_gpio,
1889	.decoder = EM28XX_TVP5150,
1890	.input = { {
1891	.type = EM28XX_VMUX_TELEVISION,
1892	.vmux = TVP5150_COMPOSITE0,
1893	.amux = EM28XX_AMUX_VIDEO,
1894	.gpio = default_analog,
1895	}, {
1896	.type = EM28XX_VMUX_COMPOSITE,
1897	.vmux = TVP5150_COMPOSITE1,
1898	.amux = EM28XX_AMUX_LINE_IN,
1899	.gpio = default_analog,
1900	}, {
1901	.type = EM28XX_VMUX_SVIDEO,
1902	.vmux = TVP5150_SVIDEO,
1903	.amux = EM28XX_AMUX_LINE_IN,
1904	.gpio = default_analog,
1905	} },
1906	},
1907	[EM2881_BOARD_PINNACLE_HYBRID_PRO] = {
1908	.name = "Pinnacle Hybrid Pro",
1909	.tuner_type = TUNER_XC2028,
1910	.tuner_gpio = default_tuner_gpio,
1911	.decoder = EM28XX_TVP5150,
1912	.has_dvb = 1,
1913	.dvb_gpio = pinnacle_hybrid_pro_digital,
1914	.input = { {
1915	.type = EM28XX_VMUX_TELEVISION,
1916	.vmux = TVP5150_COMPOSITE0,
1917	.amux = EM28XX_AMUX_VIDEO,
1918	.gpio = pinnacle_hybrid_pro_analog,
1919	}, {
1920	.type = EM28XX_VMUX_COMPOSITE,
1921	.vmux = TVP5150_COMPOSITE1,
1922	.amux = EM28XX_AMUX_LINE_IN,
1923	.gpio = pinnacle_hybrid_pro_analog,
1924	}, {
1925	.type = EM28XX_VMUX_SVIDEO,
1926	.vmux = TVP5150_SVIDEO,
1927	.amux = EM28XX_AMUX_LINE_IN,
1928	.gpio = pinnacle_hybrid_pro_analog,
1929	} },
1930	},
1931	[EM2882_BOARD_PINNACLE_HYBRID_PRO_330E] = {
1932	.name = "Pinnacle Hybrid Pro (330e)",
1933	.tuner_type = TUNER_XC2028,
1934	.tuner_gpio = default_tuner_gpio,
1935	.mts_firmware = 1,
1936	.has_dvb = 1,
1937	.dvb_gpio = hauppauge_wintv_hvr_900R2_digital,
1938	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
1939	.decoder = EM28XX_TVP5150,
1940	.input = { {
1941	.type = EM28XX_VMUX_TELEVISION,
1942	.vmux = TVP5150_COMPOSITE0,
1943	.amux = EM28XX_AMUX_VIDEO,
1944	.gpio = hauppauge_wintv_hvr_900_analog,
1945	}, {
1946	.type = EM28XX_VMUX_COMPOSITE,
1947	.vmux = TVP5150_COMPOSITE1,
1948	.amux = EM28XX_AMUX_LINE_IN,
1949	.gpio = hauppauge_wintv_hvr_900_analog,
1950	}, {
1951	.type = EM28XX_VMUX_SVIDEO,
1952	.vmux = TVP5150_SVIDEO,
1953	.amux = EM28XX_AMUX_LINE_IN,
1954	.gpio = hauppauge_wintv_hvr_900_analog,
1955	} },
1956	},
1957	[EM2882_BOARD_KWORLD_VS_DVBT] = {
1958	.name = "Kworld VS-DVB-T 323UR",
1959	.tuner_type = TUNER_XC2028,
1960	.tuner_gpio = default_tuner_gpio,
1961	.decoder = EM28XX_TVP5150,
1962	.mts_firmware = 1,
1963	.has_dvb = 1,
1964	.dvb_gpio = kworld_330u_digital,
1965	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ, /* NEC IR */
1966	.ir_codes = RC_MAP_KWORLD_315U,
1967	.input = { {
1968	.type = EM28XX_VMUX_TELEVISION,
1969	.vmux = TVP5150_COMPOSITE0,
1970	.amux = EM28XX_AMUX_VIDEO,
1971	}, {
1972	.type = EM28XX_VMUX_COMPOSITE,
1973	.vmux = TVP5150_COMPOSITE1,
1974	.amux = EM28XX_AMUX_LINE_IN,
1975	}, {
1976	.type = EM28XX_VMUX_SVIDEO,
1977	.vmux = TVP5150_SVIDEO,
1978	.amux = EM28XX_AMUX_LINE_IN,
1979	} },
1980	},
1981	[EM2882_BOARD_TERRATEC_HYBRID_XS] = {
1982	.name = "Terratec Cinergy Hybrid T USB XS (em2882)",
1983	.tuner_type = TUNER_XC2028,
1984	.tuner_gpio = default_tuner_gpio,
1985	.mts_firmware = 1,
1986	.decoder = EM28XX_TVP5150,
1987	.has_dvb = 1,
1988	.dvb_gpio = hauppauge_wintv_hvr_900_digital,
1989	.ir_codes = RC_MAP_TERRATEC_CINERGY_XS,
1990	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1991	.input = { {
1992	.type = EM28XX_VMUX_TELEVISION,
1993	.vmux = TVP5150_COMPOSITE0,
1994	.amux = EM28XX_AMUX_VIDEO,
1995	.gpio = hauppauge_wintv_hvr_900_analog,
1996	}, {
1997	.type = EM28XX_VMUX_COMPOSITE,
1998	.vmux = TVP5150_COMPOSITE1,
1999	.amux = EM28XX_AMUX_LINE_IN,
2000	.gpio = hauppauge_wintv_hvr_900_analog,
2001	}, {
2002	.type = EM28XX_VMUX_SVIDEO,
2003	.vmux = TVP5150_SVIDEO,
2004	.amux = EM28XX_AMUX_LINE_IN,
2005	.gpio = hauppauge_wintv_hvr_900_analog,
2006	} },
2007	},
2008	[EM2882_BOARD_DIKOM_DK300] = {
2009	.name = "Dikom DK300",
2010	.tuner_type = TUNER_XC2028,
2011	.tuner_gpio = default_tuner_gpio,
2012	.decoder = EM28XX_TVP5150,
2013	.mts_firmware = 1,
2014	.has_dvb = 1,
2015	.dvb_gpio = dikom_dk300_digital,
2016	.input = { {
2017	.type = EM28XX_VMUX_TELEVISION,
2018	.vmux = TVP5150_COMPOSITE0,
2019	.amux = EM28XX_AMUX_VIDEO,
2020	.gpio = default_analog,
2021	} },
2022	},
2023	[EM2883_BOARD_KWORLD_HYBRID_330U] = {
2024	.name = "Kworld PlusTV HD Hybrid 330",
2025	.tuner_type = TUNER_XC2028,
2026	.tuner_gpio = default_tuner_gpio,
2027	.decoder = EM28XX_TVP5150,
2028	.mts_firmware = 1,
2029	.has_dvb = 1,
2030	.dvb_gpio = kworld_330u_digital,
2031	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2032	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2033	EM28XX_I2C_EEPROM_ON_BOARD |
2034	EM28XX_I2C_EEPROM_KEY_VALID,
2035	.input = { {
2036	.type = EM28XX_VMUX_TELEVISION,
2037	.vmux = TVP5150_COMPOSITE0,
2038	.amux = EM28XX_AMUX_VIDEO,
2039	.gpio = kworld_330u_analog,
2040	.aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
2041	}, {
2042	.type = EM28XX_VMUX_COMPOSITE,
2043	.vmux = TVP5150_COMPOSITE1,
2044	.amux = EM28XX_AMUX_LINE_IN,
2045	.gpio = kworld_330u_analog,
2046	.aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
2047	}, {
2048	.type = EM28XX_VMUX_SVIDEO,
2049	.vmux = TVP5150_SVIDEO,
2050	.amux = EM28XX_AMUX_LINE_IN,
2051	.gpio = kworld_330u_analog,
2052	} },
2053	},
2054	[EM2820_BOARD_COMPRO_VIDEOMATE_FORYOU] = {
2055	.name = "Compro VideoMate ForYou/Stereo",
2056	.tuner_type = TUNER_LG_PAL_NEW_TAPC,
2057	.tvaudio_addr = 0xb0,
2058	.tda9887_conf = TDA9887_PRESENT,
2059	.decoder = EM28XX_TVP5150,
2060	.adecoder = EM28XX_TVAUDIO,
2061	.mute_gpio = compro_mute_gpio,
2062	.input = { {
2063	.type = EM28XX_VMUX_TELEVISION,
2064	.vmux = TVP5150_COMPOSITE0,
2065	.amux = EM28XX_AMUX_VIDEO,
2066	.gpio = compro_unmute_tv_gpio,
2067	}, {
2068	.type = EM28XX_VMUX_SVIDEO,
2069	.vmux = TVP5150_SVIDEO,
2070	.amux = EM28XX_AMUX_LINE_IN,
2071	.gpio = compro_unmute_svid_gpio,
2072	} },
2073	},
2074	[EM2860_BOARD_KAIOMY_TVNPC_U2] = {
2075	.name = "Kaiomy TVnPC U2",
2076	.vchannels = 3,
2077	.tuner_type = TUNER_XC2028,
2078	.tuner_addr = 0x61,
2079	.mts_firmware = 1,
2080	.decoder = EM28XX_TVP5150,
2081	.tuner_gpio = default_tuner_gpio,
2082	.ir_codes = RC_MAP_KAIOMY,
2083	.input = { {
2084	.type = EM28XX_VMUX_TELEVISION,
2085	.vmux = TVP5150_COMPOSITE0,
2086	.amux = EM28XX_AMUX_VIDEO,
2087
2088	}, {
2089	.type = EM28XX_VMUX_COMPOSITE,
2090	.vmux = TVP5150_COMPOSITE1,
2091	.amux = EM28XX_AMUX_LINE_IN,
2092	}, {
2093	.type = EM28XX_VMUX_SVIDEO,
2094	.vmux = TVP5150_SVIDEO,
2095	.amux = EM28XX_AMUX_LINE_IN,
2096	} },
2097	.radio = {
2098	.type = EM28XX_RADIO,
2099	.amux = EM28XX_AMUX_LINE_IN,
2100	}
2101	},
2102	[EM2860_BOARD_EASYCAP] = {
2103	.name = "Easy Cap Capture DC-60",
2104	.vchannels = 2,
2105	.tuner_type = TUNER_ABSENT,
2106	.decoder = EM28XX_SAA711X,
2107	.input = { {
2108	.type = EM28XX_VMUX_COMPOSITE,
2109	.vmux = SAA7115_COMPOSITE0,
2110	.amux = EM28XX_AMUX_LINE_IN,
2111	}, {
2112	.type = EM28XX_VMUX_SVIDEO,
2113	.vmux = SAA7115_SVIDEO3,
2114	.amux = EM28XX_AMUX_LINE_IN,
2115	} },
2116	},
2117	[EM2820_BOARD_IODATA_GVMVP_SZ] = {
2118	.name = "IO-DATA GV-MVP/SZ",
2119	.tuner_type = TUNER_PHILIPS_FM1236_MK3,
2120	.tuner_gpio = default_tuner_gpio,
2121	.tda9887_conf = TDA9887_PRESENT,
2122	.decoder = EM28XX_TVP5150,
2123	.input = { {
2124	.type = EM28XX_VMUX_TELEVISION,
2125	.vmux = TVP5150_COMPOSITE0,
2126	.amux = EM28XX_AMUX_VIDEO,
2127	}, { /* Composite has not been tested yet */
2128	.type = EM28XX_VMUX_COMPOSITE,
2129	.vmux = TVP5150_COMPOSITE1,
2130	.amux = EM28XX_AMUX_VIDEO,
2131	}, { /* S-video has not been tested yet */
2132	.type = EM28XX_VMUX_SVIDEO,
2133	.vmux = TVP5150_SVIDEO,
2134	.amux = EM28XX_AMUX_VIDEO,
2135	} },
2136	},
2137	[EM2860_BOARD_TERRATEC_GRABBY] = {
2138	.name = "Terratec Grabby",
2139	.vchannels = 2,
2140	.tuner_type = TUNER_ABSENT,
2141	.decoder = EM28XX_SAA711X,
2142	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2143	.input = { {
2144	.type = EM28XX_VMUX_COMPOSITE,
2145	.vmux = SAA7115_COMPOSITE0,
2146	.amux = EM28XX_AMUX_LINE_IN,
2147	}, {
2148	.type = EM28XX_VMUX_SVIDEO,
2149	.vmux = SAA7115_SVIDEO3,
2150	.amux = EM28XX_AMUX_LINE_IN,
2151	} },
2152	.buttons = std_snapshot_button,
2153	.leds = terratec_grabby_leds,
2154	},
2155	[EM2860_BOARD_TERRATEC_AV350] = {
2156	.name = "Terratec AV350",
2157	.vchannels = 2,
2158	.tuner_type = TUNER_ABSENT,
2159	.decoder = EM28XX_TVP5150,
2160	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2161	.mute_gpio = terratec_av350_mute_gpio,
2162	.input = { {
2163	.type = EM28XX_VMUX_COMPOSITE,
2164	.vmux = TVP5150_COMPOSITE1,
2165	.amux = EM28XX_AMUX_LINE_IN,
2166	.gpio = terratec_av350_unmute_gpio,
2167
2168	}, {
2169	.type = EM28XX_VMUX_SVIDEO,
2170	.vmux = TVP5150_SVIDEO,
2171	.amux = EM28XX_AMUX_LINE_IN,
2172	.gpio = terratec_av350_unmute_gpio,
2173	} },
2174	},
2175
2176	[EM2860_BOARD_ELGATO_VIDEO_CAPTURE] = {
2177	.name = "Elgato Video Capture",
2178	.decoder = EM28XX_SAA711X,
2179	.tuner_type = TUNER_ABSENT, /* Capture only device */
2180	.input = { {
2181	.type = EM28XX_VMUX_COMPOSITE,
2182	.vmux = SAA7115_COMPOSITE0,
2183	.amux = EM28XX_AMUX_LINE_IN,
2184	}, {
2185	.type = EM28XX_VMUX_SVIDEO,
2186	.vmux = SAA7115_SVIDEO3,
2187	.amux = EM28XX_AMUX_LINE_IN,
2188	} },
2189	},
2190
2191	[EM2882_BOARD_EVGA_INDTUBE] = {
2192	.name = "Evga inDtube",
2193	.tuner_type = TUNER_XC2028,
2194	.tuner_gpio = default_tuner_gpio,
2195	.decoder = EM28XX_TVP5150,
2196	.xclk = EM28XX_XCLK_FREQUENCY_12MHZ, /* NEC IR */
2197	.mts_firmware = 1,
2198	.has_dvb = 1,
2199	.dvb_gpio = evga_indtube_digital,
2200	.ir_codes = RC_MAP_EVGA_INDTUBE,
2201	.input = { {
2202	.type = EM28XX_VMUX_TELEVISION,
2203	.vmux = TVP5150_COMPOSITE0,
2204	.amux = EM28XX_AMUX_VIDEO,
2205	.gpio = evga_indtube_analog,
2206	}, {
2207	.type = EM28XX_VMUX_COMPOSITE,
2208	.vmux = TVP5150_COMPOSITE1,
2209	.amux = EM28XX_AMUX_LINE_IN,
2210	.gpio = evga_indtube_analog,
2211	}, {
2212	.type = EM28XX_VMUX_SVIDEO,
2213	.vmux = TVP5150_SVIDEO,
2214	.amux = EM28XX_AMUX_LINE_IN,
2215	.gpio = evga_indtube_analog,
2216	} },
2217	},
2218	/*
2219	* eb1a:2868 Empia EM2870 + Philips CU1216L NIM
2220	* (Philips TDA10023 + Infineon TUA6034)
2221	*/
2222	[EM2870_BOARD_REDDO_DVB_C_USB_BOX] = {
2223	.name = "Reddo DVB-C USB TV Box",
2224	.tuner_type = TUNER_ABSENT,
2225	.tuner_gpio = reddo_dvb_c_usb_box,
2226	.has_dvb = 1,
2227	},
2228	/*
2229	* 1b80:a340 - Empia EM2870, NXP TDA18271HD and LG DT3304, sold
2230	* initially as the KWorld PlusTV 340U, then as the UB435-Q.
2231	* Early variants have a TDA18271HD/C1, later ones a TDA18271HD/C2
2232	*/
2233	[EM2870_BOARD_KWORLD_A340] = {
2234	.name = "KWorld PlusTV 340U or UB435-Q (ATSC)",
2235	.tuner_type = TUNER_ABSENT, /* Digital-only TDA18271HD */
2236	.has_dvb = 1,
2237	.dvb_gpio = kworld_a340_digital,
2238	.tuner_gpio = default_tuner_gpio,
2239	},
2240	/*
2241	* 2013:024f PCTV nanoStick T2 290e.
2242	* Empia EM28174, Sony CXD2820R and NXP TDA18271HD/C2
2243	*/
2244	[EM28174_BOARD_PCTV_290E] = {
2245	.name = "PCTV nanoStick T2 290e",
2246	.def_i2c_bus = 1,
2247	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2248	EM28XX_I2C_FREQ_100_KHZ,
2249	.tuner_type = TUNER_ABSENT,
2250	.tuner_gpio = pctv_290e,
2251	.has_dvb = 1,
2252	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2253	},
2254	/*
2255	* 2013:024f PCTV DVB-S2 Stick 460e
2256	* Empia EM28174, NXP TDA10071, Conexant CX24118A and Allegro A8293
2257	*/
2258	[EM28174_BOARD_PCTV_460E] = {
2259	.def_i2c_bus = 1,
2260	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2261	EM28XX_I2C_FREQ_400_KHZ,
2262	.name = "PCTV DVB-S2 Stick (460e)",
2263	.tuner_type = TUNER_ABSENT,
2264	.tuner_gpio = pctv_460e,
2265	.has_dvb = 1,
2266	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2267	},
2268	/*
2269	* eb1a:5006 Honestech VIDBOX NW03
2270	* Empia EM2860, Philips SAA7113, Empia EMP202, No Tuner
2271	*/
2272	[EM2860_BOARD_HT_VIDBOX_NW03] = {
2273	.name = "Honestech Vidbox NW03",
2274	.tuner_type = TUNER_ABSENT,
2275	.decoder = EM28XX_SAA711X,
2276	.input = { {
2277	.type = EM28XX_VMUX_COMPOSITE,
2278	.vmux = SAA7115_COMPOSITE0,
2279	.amux = EM28XX_AMUX_LINE_IN,
2280	}, {
2281	.type = EM28XX_VMUX_SVIDEO,
2282	.vmux = SAA7115_SVIDEO3, /* S-VIDEO needs check */
2283	.amux = EM28XX_AMUX_LINE_IN,
2284	} },
2285	},
2286	/*
2287	* 1b80:e425 MaxMedia UB425-TC
2288	* Empia EM2874B + Micronas DRX 3913KA2 + NXP TDA18271HDC2
2289	*/
2290	[EM2874_BOARD_MAXMEDIA_UB425_TC] = {
2291	.name = "MaxMedia UB425-TC",
2292	.tuner_type = TUNER_ABSENT,
2293	.tuner_gpio = maxmedia_ub425_tc,
2294	.has_dvb = 1,
2295	.ir_codes = RC_MAP_REDDO,
2296	.def_i2c_bus = 1,
2297	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2298	EM28XX_I2C_FREQ_400_KHZ,
2299	},
2300	/*
2301	* 2304:0242 PCTV QuatroStick (510e)
2302	* Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2
2303	*/
2304	[EM2884_BOARD_PCTV_510E] = {
2305	.name = "PCTV QuatroStick (510e)",
2306	.tuner_type = TUNER_ABSENT,
2307	.tuner_gpio = pctv_510e,
2308	.has_dvb = 1,
2309	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2310	.def_i2c_bus = 1,
2311	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2312	EM28XX_I2C_FREQ_400_KHZ,
2313	},
2314	/*
2315	* 2013:0251 PCTV QuatroStick nano (520e)
2316	* Empia EM2884 + Micronas DRX 3926K + NXP TDA18271HDC2
2317	*/
2318	[EM2884_BOARD_PCTV_520E] = {
2319	.name = "PCTV QuatroStick nano (520e)",
2320	.tuner_type = TUNER_ABSENT,
2321	.tuner_gpio = pctv_520e,
2322	.has_dvb = 1,
2323	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2324	.def_i2c_bus = 1,
2325	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2326	EM28XX_I2C_FREQ_400_KHZ,
2327	},
2328	[EM2884_BOARD_TERRATEC_HTC_USB_XS] = {
2329	.name = "Terratec Cinergy HTC USB XS",
2330	.has_dvb = 1,
2331	.ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
2332	.tuner_type = TUNER_ABSENT,
2333	.def_i2c_bus = 1,
2334	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2335	EM28XX_I2C_FREQ_400_KHZ,
2336	},
2337	/*
2338	* 1b80:e1cc Delock 61959
2339	* Empia EM2874B + Micronas DRX 3913KA2 + NXP TDA18271HDC2
2340	* mostly the same as MaxMedia UB-425-TC but different remote
2341	*/
2342	[EM2874_BOARD_DELOCK_61959] = {
2343	.name = "Delock 61959",
2344	.tuner_type = TUNER_ABSENT,
2345	.tuner_gpio = maxmedia_ub425_tc,
2346	.has_dvb = 1,
2347	.ir_codes = RC_MAP_DELOCK_61959,
2348	.def_i2c_bus = 1,
2349	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2350	EM28XX_I2C_FREQ_400_KHZ,
2351	},
2352	/*
2353	* 1b80:e346 KWorld USB ATSC TV Stick UB435-Q V2
2354	* Empia EM2874B + LG DT3305 + NXP TDA18271HDC2
2355	*/
2356	[EM2874_BOARD_KWORLD_UB435Q_V2] = {
2357	.name = "KWorld USB ATSC TV Stick UB435-Q V2",
2358	.tuner_type = TUNER_ABSENT,
2359	.has_dvb = 1,
2360	.dvb_gpio = kworld_a340_digital,
2361	.tuner_gpio = default_tuner_gpio,
2362	.def_i2c_bus = 1,
2363	},
2364	/*
2365	* 1b80:e34c KWorld USB ATSC TV Stick UB435-Q V3
2366	* Empia EM2874B + LG DT3305 + NXP TDA18271HDC2
2367	*/
2368	[EM2874_BOARD_KWORLD_UB435Q_V3] = {
2369	.name = "KWorld USB ATSC TV Stick UB435-Q V3",
2370	.tuner_type = TUNER_ABSENT,
2371	.has_dvb = 1,
2372	.tuner_gpio = kworld_ub435q_v3_digital,
2373	.def_i2c_bus = 1,
2374	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2375	EM28XX_I2C_FREQ_100_KHZ,
2376	.leds = kworld_ub435q_v3_leds,
2377	},
2378	[EM2874_BOARD_PCTV_HD_MINI_80E] = {
2379	.name = "Pinnacle PCTV HD Mini",
2380	.tuner_type = TUNER_ABSENT,
2381	.has_dvb = 1,
2382	.dvb_gpio = em2874_pctv_80e_digital,
2383	.decoder = EM28XX_NODECODER,
2384	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2385	.leds = pctv_80e_leds,
2386	},
2387	/*
2388	* 1ae7:9003/9004 SpeedLink Vicious And Devine Laplace webcam
2389	* Empia EM2765 + OmniVision OV2640
2390	*/
2391	[EM2765_BOARD_SPEEDLINK_VAD_LAPLACE] = {
2392	.name = "SpeedLink Vicious And Devine Laplace webcam",
2393	.xclk = EM28XX_XCLK_FREQUENCY_24MHZ,
2394	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2395	EM28XX_I2C_FREQ_100_KHZ,
2396	.def_i2c_bus = 1,
2397	.tuner_type = TUNER_ABSENT,
2398	.is_webcam = 1,
2399	.input = { {
2400	.type = EM28XX_VMUX_COMPOSITE,
2401	.amux = EM28XX_AMUX_VIDEO,
2402	.gpio = speedlink_vad_laplace_reg_seq,
2403	} },
2404	.buttons = speedlink_vad_laplace_buttons,
2405	.leds = speedlink_vad_laplace_leds,
2406	},
2407	/*
2408	* 2013:0258 PCTV DVB-S2 Stick (461e)
2409	* Empia EM28178, Montage M88DS3103, Montage M88TS2022, Allegro A8293
2410	*/
2411	[EM28178_BOARD_PCTV_461E] = {
2412	.def_i2c_bus = 1,
2413	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2414	EM28XX_I2C_FREQ_400_KHZ,
2415	.name = "PCTV DVB-S2 Stick (461e)",
2416	.tuner_type = TUNER_ABSENT,
2417	.tuner_gpio = pctv_461e,
2418	.has_dvb = 1,
2419	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2420	},
2421	/*
2422	* 2013:0259 PCTV DVB-S2 Stick (461e_v2)
2423	* Empia EM28178, Montage M88DS3103b, Montage M88TS2022, Allegro A8293
2424	*/
2425	[EM28178_BOARD_PCTV_461E_V2] = {
2426	.def_i2c_bus = 1,
2427	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2428	EM28XX_I2C_FREQ_400_KHZ,
2429	.name = "PCTV DVB-S2 Stick (461e v2)",
2430	.tuner_type = TUNER_ABSENT,
2431	.tuner_gpio = pctv_461e,
2432	.has_dvb = 1,
2433	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2434	},
2435	/*
2436	* 2013:025f PCTV tripleStick (292e).
2437	* Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2157
2438	*/
2439	[EM28178_BOARD_PCTV_292E] = {
2440	.name = "PCTV tripleStick (292e)",
2441	.def_i2c_bus = 1,
2442	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2443	EM28XX_I2C_FREQ_400_KHZ,
2444	.tuner_type = TUNER_ABSENT,
2445	.tuner_gpio = pctv_292e,
2446	.has_dvb = 1,
2447	.ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2448	},
2449	[EM2861_BOARD_LEADTEK_VC100] = {
2450	.name = "Leadtek VC100",
2451	.tuner_type = TUNER_ABSENT, /* Capture only device */
2452	.decoder = EM28XX_TVP5150,
2453	.input = { {
2454	.type = EM28XX_VMUX_COMPOSITE,
2455	.vmux = TVP5150_COMPOSITE1,
2456	.amux = EM28XX_AMUX_LINE_IN,
2457	}, {
2458	.type = EM28XX_VMUX_SVIDEO,
2459	.vmux = TVP5150_SVIDEO,
2460	.amux = EM28XX_AMUX_LINE_IN,
2461	} },
2462	},
2463	/*
2464	* eb1a:8179 Terratec Cinergy T2 Stick HD.
2465	* Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2146
2466	*/
2467	[EM28178_BOARD_TERRATEC_T2_STICK_HD] = {
2468	.name = "Terratec Cinergy T2 Stick HD",
2469	.def_i2c_bus = 1,
2470	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2471	EM28XX_I2C_FREQ_400_KHZ,
2472	.tuner_type = TUNER_ABSENT,
2473	.tuner_gpio = terratec_t2_stick_hd,
2474	.has_dvb = 1,
2475	.ir_codes = RC_MAP_TERRATEC_SLIM_2,
2476	},
2477
2478	/*
2479	* 3275:0085 PLEX PX-BCUD.
2480	* Empia EM28178, TOSHIBA TC90532XBG, Sharp QM1D1C0042
2481	*/
2482	[EM28178_BOARD_PLEX_PX_BCUD] = {
2483	.name = "PLEX PX-BCUD",
2484	.xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ,
2485	.def_i2c_bus = 1,
2486	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
2487	.tuner_type = TUNER_ABSENT,
2488	.tuner_gpio = plex_px_bcud,
2489	.has_dvb = 1,
2490	},
2491	/*
2492	* 2040:0265 Hauppauge WinTV-dualHD (DVB version) Isoc.
2493	* 2040:8265 Hauppauge WinTV-dualHD (DVB version) Bulk.
2494	* Empia EM28274, 2x Silicon Labs Si2168, 2x Silicon Labs Si2157
2495	*/
2496	[EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB] = {
2497	.name = "Hauppauge WinTV-dualHD DVB",
2498	.def_i2c_bus = 1,
2499	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2500	EM28XX_I2C_FREQ_400_KHZ,
2501	.tuner_type = TUNER_SI2157,
2502	.tuner_gpio = hauppauge_dualhd_dvb,
2503	.has_dvb = 1,
2504	.has_dual_ts = 1,
2505	.ir_codes = RC_MAP_HAUPPAUGE,
2506	.leds = hauppauge_dualhd_leds,
2507	.input = { {
2508	.type = EM28XX_VMUX_COMPOSITE,
2509	.vmux = TVP5150_COMPOSITE1,
2510	.amux = EM28XX_AMUX_LINE_IN,
2511	} },
2512	},
2513	/*
2514	* 2040:026d Hauppauge WinTV-dualHD (model 01595 - ATSC/QAM) Isoc.
2515	* 2040:826d Hauppauge WinTV-dualHD (model 01595 - ATSC/QAM) Bulk.
2516	* Empia EM28274, 2x LG LGDT3306A, 2x Silicon Labs Si2157
2517	*/
2518	[EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595] = {
2519	.name = "Hauppauge WinTV-dualHD 01595 ATSC/QAM",
2520	.def_i2c_bus = 1,
2521	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2522	EM28XX_I2C_FREQ_400_KHZ,
2523	.tuner_type = TUNER_ABSENT,
2524	.tuner_gpio = hauppauge_dualhd_dvb,
2525	.has_dvb = 1,
2526	.has_dual_ts = 1,
2527	.ir_codes = RC_MAP_HAUPPAUGE,
2528	.leds = hauppauge_dualhd_leds,
2529	},
2530	/*
2531	* 1b80:e349 Magix USB Videowandler-2
2532	* (same chips as Honestech VIDBOX NW03)
2533	* Empia EM2860, Philips SAA7113, Empia EMP202, No Tuner
2534	*/
2535	[EM2861_BOARD_MAGIX_VIDEOWANDLER2] = {
2536	.name = "Magix USB Videowandler-2",
2537	.tuner_type = TUNER_ABSENT,
2538	.decoder = EM28XX_SAA711X,
2539	.input = { {
2540	.type = EM28XX_VMUX_COMPOSITE,
2541	.vmux = SAA7115_COMPOSITE0,
2542	.amux = EM28XX_AMUX_LINE_IN,
2543	}, {
2544	.type = EM28XX_VMUX_SVIDEO,
2545	.amux = EM28XX_AMUX_LINE_IN,
2546	} },
2547	},
2548	/*
2549	* 1f4d:1abe MyGica iGrabber
2550	* (same as several other EM2860 devices)
2551	* Empia EM2860, Philips SAA7113, Empia EMP202, No Tuner
2552	*/
2553	[EM2860_BOARD_MYGICA_IGRABBER] = {
2554	.name = "MyGica iGrabber",
2555	.vchannels = 2,
2556	.tuner_type = TUNER_ABSENT,
2557	.decoder = EM28XX_SAA711X,
2558	.input = { {
2559	.type = EM28XX_VMUX_COMPOSITE,
2560	.vmux = SAA7115_COMPOSITE0,
2561	.amux = EM28XX_AMUX_LINE_IN,
2562	}, {
2563	.type = EM28XX_VMUX_SVIDEO,
2564	.vmux = SAA7115_SVIDEO3,
2565	.amux = EM28XX_AMUX_LINE_IN,
2566	} },
2567	},
2568	/* 2040:826d Hauppauge USB QuadHD
2569	* Empia 28274, Max Linear 692 ATSC combo demod/tuner
2570	*/
2571	[EM2874_BOARD_HAUPPAUGE_USB_QUADHD] = {
2572	.name = "Hauppauge USB QuadHD ATSC",
2573	.def_i2c_bus = 1,
2574	.has_dual_ts = 1,
2575	.has_dvb = 1,
2576	.i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | EM28XX_I2C_FREQ_100_KHZ,
2577	.tuner_type = TUNER_ABSENT,
2578	.tuner_gpio = hauppauge_usb_quadhd_atsc_reg_seq,
2579	.leds = hauppauge_usb_quadhd_leds,
2580	},
2581	};
2582	EXPORT_SYMBOL_GPL(em28xx_boards);
2583
2584	static const unsigned int em28xx_bcount = ARRAY_SIZE(em28xx_boards);
2585
2586	/* table of devices that work with this driver */
2587	struct usb_device_id em28xx_id_table[] = {
2588	{ USB_DEVICE(0xeb1a, 0x2750),
2589	.driver_info = EM2750_BOARD_UNKNOWN },
2590	{ USB_DEVICE(0xeb1a, 0x2751),
2591	.driver_info = EM2750_BOARD_UNKNOWN },
2592	{ USB_DEVICE(0xeb1a, 0x2800),
2593	.driver_info = EM2800_BOARD_UNKNOWN },
2594	{ USB_DEVICE(0xeb1a, 0x2710),
2595	.driver_info = EM2820_BOARD_UNKNOWN },
2596	{ USB_DEVICE(0xeb1a, 0x2820),
2597	.driver_info = EM2820_BOARD_UNKNOWN },
2598	{ USB_DEVICE(0xeb1a, 0x2821),
2599	.driver_info = EM2820_BOARD_UNKNOWN },
2600	{ USB_DEVICE(0xeb1a, 0x2860),
2601	.driver_info = EM2820_BOARD_UNKNOWN },
2602	{ USB_DEVICE(0xeb1a, 0x2861),
2603	.driver_info = EM2820_BOARD_UNKNOWN },
2604	{ USB_DEVICE(0xeb1a, 0x2862),
2605	.driver_info = EM2820_BOARD_UNKNOWN },
2606	{ USB_DEVICE(0xeb1a, 0x2863),
2607	.driver_info = EM2820_BOARD_UNKNOWN },
2608	{ USB_DEVICE(0xeb1a, 0x2870),
2609	.driver_info = EM2820_BOARD_UNKNOWN },
2610	{ USB_DEVICE(0xeb1a, 0x2881),
2611	.driver_info = EM2820_BOARD_UNKNOWN },
2612	{ USB_DEVICE(0xeb1a, 0x2883), /* used by :Zolid Hybrid Tv Stick */
2613	.driver_info = EM2820_BOARD_UNKNOWN },
2614	{ USB_DEVICE(0xeb1a, 0x2868),
2615	.driver_info = EM2820_BOARD_UNKNOWN },
2616	{ USB_DEVICE(0xeb1a, 0x2875),
2617	.driver_info = EM2820_BOARD_UNKNOWN },
2618	{ USB_DEVICE(0xeb1a, 0x2885), /* MSI Digivox Trio */
2619	.driver_info = EM2884_BOARD_TERRATEC_H5 },
2620	{ USB_DEVICE(0xeb1a, 0xe300),
2621	.driver_info = EM2861_BOARD_KWORLD_PVRTV_300U },
2622	{ USB_DEVICE(0xeb1a, 0xe303),
2623	.driver_info = EM2860_BOARD_KAIOMY_TVNPC_U2 },
2624	{ USB_DEVICE(0xeb1a, 0xe305),
2625	.driver_info = EM2880_BOARD_KWORLD_DVB_305U },
2626	{ USB_DEVICE(0xeb1a, 0xe310),
2627	.driver_info = EM2880_BOARD_MSI_DIGIVOX_AD },
2628	{ USB_DEVICE(0xeb1a, 0xa313),
2629	.driver_info = EM2882_BOARD_KWORLD_ATSC_315U },
2630	{ USB_DEVICE(0xeb1a, 0xa316),
2631	.driver_info = EM2883_BOARD_KWORLD_HYBRID_330U },
2632	{ USB_DEVICE(0xeb1a, 0xe320),
2633	.driver_info = EM2880_BOARD_MSI_DIGIVOX_AD_II },
2634	{ USB_DEVICE(0xeb1a, 0xe323),
2635	.driver_info = EM2882_BOARD_KWORLD_VS_DVBT },
2636	{ USB_DEVICE(0xeb1a, 0xe350),
2637	.driver_info = EM2870_BOARD_KWORLD_350U },
2638	{ USB_DEVICE(0xeb1a, 0xe355),
2639	.driver_info = EM2870_BOARD_KWORLD_355U },
2640	{ USB_DEVICE(0xeb1a, 0x2801),
2641	.driver_info = EM2800_BOARD_GRABBEEX_USB2800 },
2642	{ USB_DEVICE(0xeb1a, 0xe357),
2643	.driver_info = EM2870_BOARD_KWORLD_355U },
2644	{ USB_DEVICE(0xeb1a, 0xe359),
2645	.driver_info = EM2870_BOARD_KWORLD_355U },
2646	{ USB_DEVICE(0x1b80, 0xe302), /* Kaiser Baas Video to DVD maker */
2647	.driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2648	{ USB_DEVICE(0x1b80, 0xe304), /* Kworld DVD Maker 2 */
2649	.driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2650	{ USB_DEVICE(0x0ccd, 0x0036),
2651	.driver_info = EM2820_BOARD_TERRATEC_CINERGY_250 },
2652	{ USB_DEVICE(0x0ccd, 0x004c),
2653	.driver_info = EM2880_BOARD_TERRATEC_HYBRID_XS_FR },
2654	{ USB_DEVICE(0x0ccd, 0x004f),
2655	.driver_info = EM2860_BOARD_TERRATEC_HYBRID_XS },
2656	{ USB_DEVICE(0x0ccd, 0x005e),
2657	.driver_info = EM2882_BOARD_TERRATEC_HYBRID_XS },
2658	{ USB_DEVICE(0x0ccd, 0x0042),
2659	.driver_info = EM2882_BOARD_TERRATEC_HYBRID_XS },
2660	{ USB_DEVICE(0x0ccd, 0x0043),
2661	.driver_info = EM2870_BOARD_TERRATEC_XS_MT2060 },
2662	{ USB_DEVICE(0x0ccd, 0x008e), /* Cinergy HTC USB XS Rev. 1 */
2663	.driver_info = EM2884_BOARD_TERRATEC_HTC_USB_XS },
2664	{ USB_DEVICE(0x0ccd, 0x00ac), /* Cinergy HTC USB XS Rev. 2 */
2665	.driver_info = EM2884_BOARD_TERRATEC_HTC_USB_XS },
2666	{ USB_DEVICE(0x0ccd, 0x10a2), /* H5 Rev. 1 */
2667	.driver_info = EM2884_BOARD_TERRATEC_H5 },
2668	{ USB_DEVICE(0x0ccd, 0x10ad), /* H5 Rev. 2 */
2669	.driver_info = EM2884_BOARD_TERRATEC_H5 },
2670	{ USB_DEVICE(0x0ccd, 0x10b6), /* H5 Rev. 3 */
2671	.driver_info = EM2884_BOARD_TERRATEC_H5 },
2672	{ USB_DEVICE(0x0ccd, 0x10b2), /* H6 */
2673	.driver_info = EM2884_BOARD_TERRATEC_H6 },
2674	{ USB_DEVICE(0x0ccd, 0x0084),
2675	.driver_info = EM2860_BOARD_TERRATEC_AV350 },
2676	{ USB_DEVICE(0x0ccd, 0x0096),
2677	.driver_info = EM2860_BOARD_TERRATEC_GRABBY },
2678	{ USB_DEVICE(0x0ccd, 0x10AF),
2679	.driver_info = EM2860_BOARD_TERRATEC_GRABBY },
2680	{ USB_DEVICE(0x0ccd, 0x00b2),
2681	.driver_info = EM2884_BOARD_CINERGY_HTC_STICK },
2682	{ USB_DEVICE(0x0fd9, 0x0018),
2683	.driver_info = EM2884_BOARD_ELGATO_EYETV_HYBRID_2008 },
2684	{ USB_DEVICE(0x0fd9, 0x0033),
2685	.driver_info = EM2860_BOARD_ELGATO_VIDEO_CAPTURE },
2686	{ USB_DEVICE(0x185b, 0x2870),
2687	.driver_info = EM2870_BOARD_COMPRO_VIDEOMATE },
2688	{ USB_DEVICE(0x185b, 0x2041),
2689	.driver_info = EM2820_BOARD_COMPRO_VIDEOMATE_FORYOU },
2690	{ USB_DEVICE(0x2040, 0x4200),
2691	.driver_info = EM2820_BOARD_HAUPPAUGE_WINTV_USB_2 },
2692	{ USB_DEVICE(0x2040, 0x4201),
2693	.driver_info = EM2820_BOARD_HAUPPAUGE_WINTV_USB_2 },
2694	{ USB_DEVICE(0x2040, 0x6500),
2695	.driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900 },
2696	{ USB_DEVICE(0x2040, 0x6502),
2697	.driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2 },
2698	{ USB_DEVICE(0x2040, 0x6513), /* HCW HVR-980 */
2699	.driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950 },
2700	{ USB_DEVICE(0x2040, 0x6517), /* HP HVR-950 */
2701	.driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950 },
2702	{ USB_DEVICE(0x2040, 0x651b), /* RP HVR-950 */
2703	.driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950 },
2704	{ USB_DEVICE(0x2040, 0x651f),
2705	.driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850 },
2706	{ USB_DEVICE(0x2040, 0x0265),
2707	.driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB },
2708	{ USB_DEVICE(0x2040, 0x8265),
2709	.driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB },
2710	{ USB_DEVICE(0x2040, 0x026d),
2711	.driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595 },
2712	{ USB_DEVICE(0x2040, 0x826d),
2713	.driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595 },
2714	{ USB_DEVICE(0x2040, 0x846d),
2715	.driver_info = EM2874_BOARD_HAUPPAUGE_USB_QUADHD },
2716	{ USB_DEVICE(0x0438, 0xb002),
2717	.driver_info = EM2880_BOARD_AMD_ATI_TV_WONDER_HD_600 },
2718	{ USB_DEVICE(0x2001, 0xf112),
2719	.driver_info = EM2820_BOARD_DLINK_USB_TV },
2720	{ USB_DEVICE(0x2304, 0x0207),
2721	.driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2722	{ USB_DEVICE(0x2304, 0x0208),
2723	.driver_info = EM2820_BOARD_PINNACLE_USB_2 },
2724	{ USB_DEVICE(0x2304, 0x021a),
2725	.driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2726	{ USB_DEVICE(0x2304, 0x0226),
2727	.driver_info = EM2882_BOARD_PINNACLE_HYBRID_PRO_330E },
2728	{ USB_DEVICE(0x2304, 0x0227),
2729	.driver_info = EM2880_BOARD_PINNACLE_PCTV_HD_PRO },
2730	{ USB_DEVICE(0x2304, 0x023f),
2731	.driver_info = EM2874_BOARD_PCTV_HD_MINI_80E },
2732	{ USB_DEVICE(0x0413, 0x6023),
2733	.driver_info = EM2800_BOARD_LEADTEK_WINFAST_USBII },
2734	{ USB_DEVICE(0x093b, 0xa003),
2735	.driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2736	{ USB_DEVICE(0x093b, 0xa005),
2737	.driver_info = EM2861_BOARD_PLEXTOR_PX_TV100U },
2738	{ USB_DEVICE(0x04bb, 0x0515),
2739	.driver_info = EM2820_BOARD_IODATA_GVMVP_SZ },
2740	{ USB_DEVICE(0xeb1a, 0x50a6),
2741	.driver_info = EM2860_BOARD_GADMEI_UTV330 },
2742	{ USB_DEVICE(0x1b80, 0xa340),
2743	.driver_info = EM2870_BOARD_KWORLD_A340 },
2744	{ USB_DEVICE(0x1b80, 0xe346),
2745	.driver_info = EM2874_BOARD_KWORLD_UB435Q_V2 },
2746	{ USB_DEVICE(0x1b80, 0xe34c),
2747	.driver_info = EM2874_BOARD_KWORLD_UB435Q_V3 },
2748	{ USB_DEVICE(0x2013, 0x024f),
2749	.driver_info = EM28174_BOARD_PCTV_290E },
2750	{ USB_DEVICE(0x2013, 0x024c),
2751	.driver_info = EM28174_BOARD_PCTV_460E },
2752	{ USB_DEVICE(0x2040, 0x1605),
2753	.driver_info = EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C },
2754	{ USB_DEVICE(0x1b80, 0xe755),
2755	.driver_info = EM2884_BOARD_C3TECH_DIGITAL_DUO },
2756	{ USB_DEVICE(0xeb1a, 0x5006),
2757	.driver_info = EM2860_BOARD_HT_VIDBOX_NW03 },
2758	{ USB_DEVICE(0x1b80, 0xe309), /* Sveon STV40 */
2759	.driver_info = EM2860_BOARD_EASYCAP },
2760	{ USB_DEVICE(0x1b80, 0xe425),
2761	.driver_info = EM2874_BOARD_MAXMEDIA_UB425_TC },
2762	{ USB_DEVICE(0x1f4d, 0x1abe),
2763	.driver_info = EM2860_BOARD_MYGICA_IGRABBER },
2764	{ USB_DEVICE(0x2304, 0x0242),
2765	.driver_info = EM2884_BOARD_PCTV_510E },
2766	{ USB_DEVICE(0x2013, 0x0251),
2767	.driver_info = EM2884_BOARD_PCTV_520E },
2768	{ USB_DEVICE(0x1b80, 0xe1cc),
2769	.driver_info = EM2874_BOARD_DELOCK_61959 },
2770	{ USB_DEVICE(0x1ae7, 0x9003),
2771	.driver_info = EM2765_BOARD_SPEEDLINK_VAD_LAPLACE },
2772	{ USB_DEVICE(0x1ae7, 0x9004),
2773	.driver_info = EM2765_BOARD_SPEEDLINK_VAD_LAPLACE },
2774	{ USB_DEVICE(0x2013, 0x0258),
2775	.driver_info = EM28178_BOARD_PCTV_461E },
2776	{ USB_DEVICE(0x2013, 0x8258), /* Bulk transport 461e */
2777	.driver_info = EM28178_BOARD_PCTV_461E },
2778	{ USB_DEVICE(0x2013, 0x0461),
2779	.driver_info = EM28178_BOARD_PCTV_461E_V2 },
2780	{ USB_DEVICE(0x2013, 0x8461), /* Bulk transport 461e v2 */
2781	.driver_info = EM28178_BOARD_PCTV_461E_V2 },
2782	{ USB_DEVICE(0x2013, 0x0259),
2783	.driver_info = EM28178_BOARD_PCTV_461E_V2 },
2784	{ USB_DEVICE(0x2013, 0x025f),
2785	.driver_info = EM28178_BOARD_PCTV_292E },
2786	{ USB_DEVICE(0x2013, 0x0264), /* Hauppauge WinTV-soloHD 292e SE */
2787	.driver_info = EM28178_BOARD_PCTV_292E },
2788	{ USB_DEVICE(0x2040, 0x0264), /* Hauppauge WinTV-soloHD Isoc */
2789	.driver_info = EM28178_BOARD_PCTV_292E },
2790	{ USB_DEVICE(0x2040, 0x8264), /* Hauppauge OEM Generic WinTV-soloHD Bulk */
2791	.driver_info = EM28178_BOARD_PCTV_292E },
2792	{ USB_DEVICE(0x2040, 0x8268), /* Hauppauge Retail WinTV-soloHD Bulk */
2793	.driver_info = EM28178_BOARD_PCTV_292E },
2794	{ USB_DEVICE(0x0413, 0x6f07),
2795	.driver_info = EM2861_BOARD_LEADTEK_VC100 },
2796	{ USB_DEVICE(0xeb1a, 0x8179),
2797	.driver_info = EM28178_BOARD_TERRATEC_T2_STICK_HD },
2798	{ USB_DEVICE(0x3275, 0x0085),
2799	.driver_info = EM28178_BOARD_PLEX_PX_BCUD },
2800	{ USB_DEVICE(0xeb1a, 0x5051), /* Ion Video 2 PC MKII / Startech svid2usb23 / Raygo R12-41373 */
2801	.driver_info = EM2860_BOARD_TVP5150_REFERENCE_DESIGN },
2802	{ USB_DEVICE(0x1b80, 0xe349), /* Magix USB Videowandler-2 */
2803	.driver_info = EM2861_BOARD_MAGIX_VIDEOWANDLER2 },
2804	{ },
2805	};
2806	MODULE_DEVICE_TABLE(usb, em28xx_id_table);
2807
2808	/*
2809	* EEPROM hash table for devices with generic USB IDs
2810	*/
2811	static const struct em28xx_hash_table em28xx_eeprom_hash[] = {
2812	/* P/N: SA 60002070465 Tuner: TVF7533-MF */
2813	{0x6ce05a8f, EM2820_BOARD_PROLINK_PLAYTV_USB2, TUNER_YMEC_TVF_5533MF},
2814	{0x72cc5a8b, EM2820_BOARD_PROLINK_PLAYTV_BOX4_USB2, TUNER_YMEC_TVF_5533MF},
2815	{0x966a0441, EM2880_BOARD_KWORLD_DVB_310U, TUNER_XC2028},
2816	{0x166a0441, EM2880_BOARD_EMPIRE_DUAL_TV, TUNER_XC2028},
2817	{0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028},
2818	{0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028},
2819	{0x63f653bd, EM2870_BOARD_REDDO_DVB_C_USB_BOX, TUNER_ABSENT},
2820	{0x4e913442, EM2882_BOARD_DIKOM_DK300, TUNER_XC2028},
2821	{0x85dd871e, EM2882_BOARD_ZOLID_HYBRID_TV_STICK, TUNER_XC2028},
2822	};
2823
2824	/* I2C devicelist hash table for devices with generic USB IDs */
2825	static const struct em28xx_hash_table em28xx_i2c_hash[] = {
2826	{0xb06a32c3, EM2800_BOARD_TERRATEC_CINERGY_200, TUNER_LG_PAL_NEW_TAPC},
2827	{0xf51200e3, EM2800_BOARD_VGEAR_POCKETTV, TUNER_LG_PAL_NEW_TAPC},
2828	{0x1ba50080, EM2860_BOARD_SAA711X_REFERENCE_DESIGN, TUNER_ABSENT},
2829	{0x77800080, EM2860_BOARD_TVP5150_REFERENCE_DESIGN, TUNER_ABSENT},
2830	{0xc51200e3, EM2820_BOARD_GADMEI_TVR200, TUNER_LG_PAL_NEW_TAPC},
2831	{0x4ba50080, EM2861_BOARD_GADMEI_UTV330PLUS, TUNER_TNF_5335MF},
2832	{0x6b800080, EM2874_BOARD_LEADERSHIP_ISDBT, TUNER_ABSENT},
2833	{0x27e10080, EM2882_BOARD_ZOLID_HYBRID_TV_STICK, TUNER_XC2028},
2834	};
2835
2836	/* NOTE: introduce a separate hash table for devices with 16 bit eeproms */
2837
2838	int em28xx_tuner_callback(void *ptr, int component, int command, int arg)
2839	{
2840	struct em28xx_i2c_bus *i2c_bus = ptr;
2841	struct em28xx *dev = i2c_bus->dev;
2842	int rc = 0;
2843
2844	if (dev->tuner_type != TUNER_XC2028 && dev->tuner_type != TUNER_XC5000)
2845	return 0;
2846
2847	if (command != XC2028_TUNER_RESET && command != XC5000_TUNER_RESET)
2848	return 0;
2849
2850	rc = em28xx_gpio_set(dev, gpio: dev->board.tuner_gpio);
2851
2852	return rc;
2853	}
2854	EXPORT_SYMBOL_GPL(em28xx_tuner_callback);
2855
2856	static inline void em28xx_set_xclk_i2c_speed(struct em28xx *dev)
2857	{
2858	const struct em28xx_board *board = &em28xx_boards[dev->model];
2859	u8 xclk = board->xclk, i2c_speed = board->i2c_speed;
2860
2861	/*
2862	* Those are the default values for the majority of boards
2863	* Use those values if not specified otherwise at boards entry
2864	*/
2865	if (!xclk)
2866	xclk = EM28XX_XCLK_IR_RC5_MODE |
2867	EM28XX_XCLK_FREQUENCY_12MHZ;
2868
2869	em28xx_write_reg(dev, EM28XX_R0F_XCLK, val: xclk);
2870
2871	if (!i2c_speed)
2872	i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2873	EM28XX_I2C_FREQ_100_KHZ;
2874
2875	dev->i2c_speed = i2c_speed & 0x03;
2876
2877	if (!dev->board.is_em2800)
2878	em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, val: i2c_speed);
2879	msleep(msecs: 50);
2880	}
2881
2882	static inline void em28xx_set_model(struct em28xx *dev)
2883	{
2884	dev->board = em28xx_boards[dev->model];
2885	dev->has_msp34xx = dev->board.has_msp34xx;
2886	dev->is_webcam = dev->board.is_webcam;
2887
2888	em28xx_set_xclk_i2c_speed(dev);
2889
2890	/* Should be initialized early, for I2C to work */
2891	dev->def_i2c_bus = dev->board.def_i2c_bus;
2892	}
2893
2894	/*
2895	* Wait until AC97_RESET reports the expected value reliably before proceeding.
2896	* We also check that two unrelated registers accesses don't return the same
2897	* value to avoid premature return.
2898	* This procedure helps ensuring AC97 register accesses are reliable.
2899	*/
2900	static int em28xx_wait_until_ac97_features_equals(struct em28xx *dev,
2901	int expected_feat)
2902	{
2903	unsigned long timeout = jiffies + msecs_to_jiffies(m: 2000);
2904	int feat, powerdown;
2905
2906	while (time_is_after_jiffies(timeout)) {
2907	feat = em28xx_read_ac97(dev, AC97_RESET);
2908	if (feat < 0)
2909	return feat;
2910
2911	powerdown = em28xx_read_ac97(dev, AC97_POWERDOWN);
2912	if (powerdown < 0)
2913	return powerdown;
2914
2915	if (feat == expected_feat && feat != powerdown)
2916	return 0;
2917
2918	msleep(msecs: 50);
2919	}
2920
2921	dev_warn(&dev->intf->dev, "AC97 registers access is not reliable !\n");
2922	return -ETIMEDOUT;
2923	}
2924
2925	/*
2926	* Since em28xx_pre_card_setup() requires a proper dev->model,
2927	* this won't work for boards with generic PCI IDs
2928	*/
2929	static void em28xx_pre_card_setup(struct em28xx *dev)
2930	{
2931	/*
2932	* Set the initial XCLK and I2C clock values based on the board
2933	* definition
2934	*/
2935	em28xx_set_xclk_i2c_speed(dev);
2936
2937	/* request some modules */
2938	switch (dev->model) {
2939	case EM2861_BOARD_PLEXTOR_PX_TV100U:
2940	/* Sets the msp34xx I2S speed */
2941	dev->i2s_speed = 2048000;
2942	break;
2943	case EM2861_BOARD_KWORLD_PVRTV_300U:
2944	case EM2880_BOARD_KWORLD_DVB_305U:
2945	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0x6d);
2946	usleep_range(min: 10000, max: 11000);
2947	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0x7d);
2948	usleep_range(min: 10000, max: 11000);
2949	break;
2950	case EM2870_BOARD_COMPRO_VIDEOMATE:
2951	/*
2952	* TODO: someone can do some cleanup here...
2953	* not everything's needed
2954	*/
2955	em28xx_write_reg(dev, EM2880_R04_GPO, val: 0x00);
2956	usleep_range(min: 10000, max: 11000);
2957	em28xx_write_reg(dev, EM2880_R04_GPO, val: 0x01);
2958	usleep_range(min: 10000, max: 11000);
2959	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfd);
2960	msleep(msecs: 70);
2961	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfc);
2962	msleep(msecs: 70);
2963	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xdc);
2964	msleep(msecs: 70);
2965	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfc);
2966	msleep(msecs: 70);
2967	break;
2968	case EM2870_BOARD_TERRATEC_XS_MT2060:
2969	/*
2970	* this device needs some gpio writes to get the DVB-T
2971	* demod work
2972	*/
2973	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfe);
2974	msleep(msecs: 70);
2975	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xde);
2976	msleep(msecs: 70);
2977	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfe);
2978	msleep(msecs: 70);
2979	break;
2980	case EM2870_BOARD_PINNACLE_PCTV_DVB:
2981	/*
2982	* this device needs some gpio writes to get the
2983	* DVB-T demod work
2984	*/
2985	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfe);
2986	msleep(msecs: 70);
2987	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xde);
2988	msleep(msecs: 70);
2989	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfe);
2990	msleep(msecs: 70);
2991	break;
2992	case EM2820_BOARD_GADMEI_UTV310:
2993	case EM2820_BOARD_MSI_VOX_USB_2:
2994	/* enables audio for that devices */
2995	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfd);
2996	break;
2997
2998	case EM2882_BOARD_KWORLD_ATSC_315U:
2999	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xff);
3000	usleep_range(min: 10000, max: 11000);
3001	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfe);
3002	usleep_range(min: 10000, max: 11000);
3003	em28xx_write_reg(dev, EM2880_R04_GPO, val: 0x00);
3004	usleep_range(min: 10000, max: 11000);
3005	em28xx_write_reg(dev, EM2880_R04_GPO, val: 0x08);
3006	usleep_range(min: 10000, max: 11000);
3007	break;
3008
3009	case EM2860_BOARD_KAIOMY_TVNPC_U2:
3010	em28xx_write_regs(dev, EM28XX_R0F_XCLK, buf: "\x07", len: 1);
3011	em28xx_write_regs(dev, EM28XX_R06_I2C_CLK, buf: "\x40", len: 1);
3012	em28xx_write_regs(dev, reg: 0x0d, buf: "\x42", len: 1);
3013	em28xx_write_regs(dev, reg: 0x08, buf: "\xfd", len: 1);
3014	usleep_range(min: 10000, max: 11000);
3015	em28xx_write_regs(dev, reg: 0x08, buf: "\xff", len: 1);
3016	usleep_range(min: 10000, max: 11000);
3017	em28xx_write_regs(dev, reg: 0x08, buf: "\x7f", len: 1);
3018	usleep_range(min: 10000, max: 11000);
3019	em28xx_write_regs(dev, reg: 0x08, buf: "\x6b", len: 1);
3020
3021	break;
3022	case EM2860_BOARD_EASYCAP:
3023	em28xx_write_regs(dev, reg: 0x08, buf: "\xf8", len: 1);
3024	break;
3025
3026	case EM2820_BOARD_IODATA_GVMVP_SZ:
3027	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xff);
3028	msleep(msecs: 70);
3029	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xf7);
3030	usleep_range(min: 10000, max: 11000);
3031	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfe);
3032	msleep(msecs: 70);
3033	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfd);
3034	msleep(msecs: 70);
3035	break;
3036
3037	case EM2860_BOARD_TERRATEC_GRABBY:
3038	/*
3039	* HACK?: Ensure AC97 register reading is reliable before
3040	* proceeding. In practice, this will wait about 1.6 seconds.
3041	*/
3042	em28xx_wait_until_ac97_features_equals(dev, expected_feat: 0x6a90);
3043	break;
3044	}
3045
3046	em28xx_gpio_set(dev, gpio: dev->board.tuner_gpio);
3047	em28xx_set_mode(dev, set_mode: EM28XX_ANALOG_MODE);
3048
3049	/* Unlock device */
3050	em28xx_set_mode(dev, set_mode: EM28XX_SUSPEND);
3051	}
3052
3053	static int em28xx_hint_board(struct em28xx *dev)
3054	{
3055	int i;
3056
3057	if (dev->is_webcam) {
3058	if (dev->em28xx_sensor == EM28XX_MT9V011) {
3059	dev->model = EM2820_BOARD_SILVERCREST_WEBCAM;
3060	} else if (dev->em28xx_sensor == EM28XX_MT9M001 ||
3061	dev->em28xx_sensor == EM28XX_MT9M111) {
3062	dev->model = EM2750_BOARD_UNKNOWN;
3063	}
3064	/* FIXME: IMPROVE ! */
3065
3066	return 0;
3067	}
3068
3069	/*
3070	* HINT method: EEPROM
3071	*
3072	* This method works only for boards with eeprom.
3073	* Uses a hash of all eeprom bytes. The hash should be
3074	* unique for a vendor/tuner pair.
3075	* There are a high chance that tuners for different
3076	* video standards produce different hashes.
3077	*/
3078	for (i = 0; i < ARRAY_SIZE(em28xx_eeprom_hash); i++) {
3079	if (dev->hash == em28xx_eeprom_hash[i].hash) {
3080	dev->model = em28xx_eeprom_hash[i].model;
3081	dev->tuner_type = em28xx_eeprom_hash[i].tuner;
3082
3083	dev_err(&dev->intf->dev,
3084	"Your board has no unique USB ID.\n"
3085	"A hint were successfully done, based on eeprom hash.\n"
3086	"This method is not 100%% failproof.\n"
3087	"If the board were misdetected, please email this log to:\n"
3088	"\tV4L Mailing List <linux-media@vger.kernel.org>\n"
3089	"Board detected as %s\n",
3090	em28xx_boards[dev->model].name);
3091
3092	return 0;
3093	}
3094	}
3095
3096	/*
3097	* HINT method: I2C attached devices
3098	*
3099	* This method works for all boards.
3100	* Uses a hash of i2c scanned devices.
3101	* Devices with the same i2c attached chips will
3102	* be considered equal.
3103	* This method is less precise than the eeprom one.
3104	*/
3105
3106	/* user did not request i2c scanning => do it now */
3107	if (!dev->i2c_hash)
3108	em28xx_do_i2c_scan(dev, bus: dev->def_i2c_bus);
3109
3110	for (i = 0; i < ARRAY_SIZE(em28xx_i2c_hash); i++) {
3111	if (dev->i2c_hash == em28xx_i2c_hash[i].hash) {
3112	dev->model = em28xx_i2c_hash[i].model;
3113	dev->tuner_type = em28xx_i2c_hash[i].tuner;
3114	dev_err(&dev->intf->dev,
3115	"Your board has no unique USB ID.\n"
3116	"A hint were successfully done, based on i2c devicelist hash.\n"
3117	"This method is not 100%% failproof.\n"
3118	"If the board were misdetected, please email this log to:\n"
3119	"\tV4L Mailing List <linux-media@vger.kernel.org>\n"
3120	"Board detected as %s\n",
3121	em28xx_boards[dev->model].name);
3122
3123	return 0;
3124	}
3125	}
3126
3127	dev_err(&dev->intf->dev,
3128	"Your board has no unique USB ID and thus need a hint to be detected.\n"
3129	"You may try to use card=<n> insmod option to workaround that.\n"
3130	"Please send an email with this log to:\n"
3131	"\tV4L Mailing List <linux-media@vger.kernel.org>\n"
3132	"Board eeprom hash is 0x%08lx\n"
3133	"Board i2c devicelist hash is 0x%08lx\n",
3134	dev->hash, dev->i2c_hash);
3135
3136	dev_err(&dev->intf->dev,
3137	"Here is a list of valid choices for the card=<n> insmod option:\n");
3138	for (i = 0; i < em28xx_bcount; i++) {
3139	dev_err(&dev->intf->dev,
3140	" card=%d -> %s\n", i, em28xx_boards[i].name);
3141	}
3142	return -1;
3143	}
3144
3145	static void em28xx_card_setup(struct em28xx *dev)
3146	{
3147	int i, j, idx;
3148	bool duplicate_entry;
3149
3150	/*
3151	* If the device can be a webcam, seek for a sensor.
3152	* If sensor is not found, then it isn't a webcam.
3153	*/
3154	if (dev->is_webcam) {
3155	em28xx_detect_sensor(dev);
3156	if (dev->em28xx_sensor == EM28XX_NOSENSOR)
3157	/* NOTE: error/unknown sensor/no sensor */
3158	dev->is_webcam = 0;
3159	}
3160
3161	switch (dev->model) {
3162	case EM2750_BOARD_UNKNOWN:
3163	case EM2820_BOARD_UNKNOWN:
3164	case EM2800_BOARD_UNKNOWN:
3165	/*
3166	* The K-WORLD DVB-T 310U is detected as an MSI Digivox AD.
3167	*
3168	* This occurs because they share identical USB vendor and
3169	* product IDs.
3170	*
3171	* What we do here is look up the EEPROM hash of the K-WORLD
3172	* and if it is found then we decide that we do not have
3173	* a DIGIVOX and reset the device to the K-WORLD instead.
3174	*
3175	* This solution is only valid if they do not share eeprom
3176	* hash identities which has not been determined as yet.
3177	*/
3178	if (em28xx_hint_board(dev) < 0) {
3179	dev_err(&dev->intf->dev, "Board not discovered\n");
3180	} else {
3181	em28xx_set_model(dev);
3182	em28xx_pre_card_setup(dev);
3183	}
3184	break;
3185	default:
3186	em28xx_set_model(dev);
3187	}
3188
3189	dev_info(&dev->intf->dev, "Identified as %s (card=%d)\n",
3190	dev->board.name, dev->model);
3191
3192	dev->tuner_type = em28xx_boards[dev->model].tuner_type;
3193
3194	/* request some modules */
3195	switch (dev->model) {
3196	case EM2820_BOARD_HAUPPAUGE_WINTV_USB_2:
3197	case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
3198	case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2:
3199	case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850:
3200	case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950:
3201	case EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C:
3202	case EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB:
3203	case EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595:
3204	{
3205	struct tveeprom tv;
3206
3207	if (!dev->eedata)
3208	break;
3209	#if defined(CONFIG_MODULES) && defined(MODULE)
3210	request_module("tveeprom");
3211	#endif
3212	/* Call first TVeeprom */
3213
3214	tveeprom_hauppauge_analog(tvee: &tv, eeprom_data: dev->eedata);
3215
3216	dev->tuner_type = tv.tuner_type;
3217
3218	if (tv.audio_processor == TVEEPROM_AUDPROC_MSP) {
3219	dev->i2s_speed = 2048000;
3220	dev->has_msp34xx = 1;
3221	}
3222	break;
3223	}
3224	case EM2882_BOARD_KWORLD_ATSC_315U:
3225	em28xx_write_reg(dev, reg: 0x0d, val: 0x42);
3226	usleep_range(min: 10000, max: 11000);
3227	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xfd);
3228	usleep_range(min: 10000, max: 11000);
3229	break;
3230	case EM2820_BOARD_KWORLD_PVRTV2800RF:
3231	/* GPIO enables sound on KWORLD PVR TV 2800RF */
3232	em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, val: 0xf9);
3233	break;
3234	case EM2820_BOARD_UNKNOWN:
3235	case EM2800_BOARD_UNKNOWN:
3236	/*
3237	* The K-WORLD DVB-T 310U is detected as an MSI Digivox AD.
3238	*
3239	* This occurs because they share identical USB vendor and
3240	* product IDs.
3241	*
3242	* What we do here is look up the EEPROM hash of the K-WORLD
3243	* and if it is found then we decide that we do not have
3244	* a DIGIVOX and reset the device to the K-WORLD instead.
3245	*
3246	* This solution is only valid if they do not share eeprom
3247	* hash identities which has not been determined as yet.
3248	*/
3249	case EM2880_BOARD_MSI_DIGIVOX_AD:
3250	if (!em28xx_hint_board(dev))
3251	em28xx_set_model(dev);
3252
3253	/*
3254	* In cases where we had to use a board hint, the call to
3255	* em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
3256	* so make the call now so the analog GPIOs are set properly
3257	* before probing the i2c bus.
3258	*/
3259	em28xx_gpio_set(dev, gpio: dev->board.tuner_gpio);
3260	em28xx_set_mode(dev, set_mode: EM28XX_ANALOG_MODE);
3261	break;
3262
3263	/*
3264	* The Dikom DK300 is detected as an Kworld VS-DVB-T 323UR.
3265	*
3266	* This occurs because they share identical USB vendor and
3267	* product IDs.
3268	*
3269	* What we do here is look up the EEPROM hash of the Dikom
3270	* and if it is found then we decide that we do not have
3271	* a Kworld and reset the device to the Dikom instead.
3272	*
3273	* This solution is only valid if they do not share eeprom
3274	* hash identities which has not been determined as yet.
3275	*/
3276	case EM2882_BOARD_KWORLD_VS_DVBT:
3277	if (!em28xx_hint_board(dev))
3278	em28xx_set_model(dev);
3279
3280	/*
3281	* In cases where we had to use a board hint, the call to
3282	* em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
3283	* so make the call now so the analog GPIOs are set properly
3284	* before probing the i2c bus.
3285	*/
3286	em28xx_gpio_set(dev, gpio: dev->board.tuner_gpio);
3287	em28xx_set_mode(dev, set_mode: EM28XX_ANALOG_MODE);
3288	break;
3289	}
3290
3291	if (dev->board.valid == EM28XX_BOARD_NOT_VALIDATED) {
3292	dev_err(&dev->intf->dev,
3293	"\n\n"
3294	"The support for this board weren't valid yet.\n"
3295	"Please send a report of having this working\n"
3296	"not to V4L mailing list (and/or to other addresses)\n\n");
3297	}
3298
3299	/* Free eeprom data memory */
3300	kfree(objp: dev->eedata);
3301	dev->eedata = NULL;
3302
3303	/* Allow override tuner type by a module parameter */
3304	if (tuner >= 0)
3305	dev->tuner_type = tuner;
3306
3307	/*
3308	* Dynamically generate a list of valid audio inputs for this
3309	* specific board, mapping them via enum em28xx_amux.
3310	*/
3311
3312	idx = 0;
3313	for (i = 0; i < MAX_EM28XX_INPUT; i++) {
3314	if (!INPUT(i)->type)
3315	continue;
3316
3317	/* Skip already mapped audio inputs */
3318	duplicate_entry = false;
3319	for (j = 0; j < idx; j++) {
3320	if (INPUT(i)->amux == dev->amux_map[j]) {
3321	duplicate_entry = true;
3322	break;
3323	}
3324	}
3325	if (duplicate_entry)
3326	continue;
3327
3328	dev->amux_map[idx++] = INPUT(i)->amux;
3329	}
3330	for (; idx < MAX_EM28XX_INPUT; idx++)
3331	dev->amux_map[idx] = EM28XX_AMUX_UNUSED;
3332	}
3333
3334	void em28xx_setup_xc3028(struct em28xx *dev, struct xc2028_ctrl *ctl)
3335	{
3336	memset(ctl, 0, sizeof(*ctl));
3337
3338	ctl->fname = XC2028_DEFAULT_FIRMWARE;
3339	ctl->max_len = 64;
3340	ctl->mts = em28xx_boards[dev->model].mts_firmware;
3341
3342	switch (dev->model) {
3343	case EM2880_BOARD_EMPIRE_DUAL_TV:
3344	case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
3345	case EM2882_BOARD_TERRATEC_HYBRID_XS:
3346	case EM2880_BOARD_TERRATEC_HYBRID_XS:
3347	case EM2880_BOARD_TERRATEC_HYBRID_XS_FR:
3348	case EM2881_BOARD_PINNACLE_HYBRID_PRO:
3349	case EM2882_BOARD_ZOLID_HYBRID_TV_STICK:
3350	ctl->demod = XC3028_FE_ZARLINK456;
3351	break;
3352	case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2:
3353	case EM2882_BOARD_PINNACLE_HYBRID_PRO_330E:
3354	ctl->demod = XC3028_FE_DEFAULT;
3355	break;
3356	case EM2880_BOARD_AMD_ATI_TV_WONDER_HD_600:
3357	ctl->demod = XC3028_FE_DEFAULT;
3358	ctl->fname = XC3028L_DEFAULT_FIRMWARE;
3359	break;
3360	case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850:
3361	case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950:
3362	case EM2880_BOARD_PINNACLE_PCTV_HD_PRO:
3363	/* FIXME: Better to specify the needed IF */
3364	ctl->demod = XC3028_FE_DEFAULT;
3365	break;
3366	case EM2883_BOARD_KWORLD_HYBRID_330U:
3367	case EM2882_BOARD_DIKOM_DK300:
3368	case EM2882_BOARD_KWORLD_VS_DVBT:
3369	ctl->demod = XC3028_FE_CHINA;
3370	ctl->fname = XC2028_DEFAULT_FIRMWARE;
3371	break;
3372	case EM2882_BOARD_EVGA_INDTUBE:
3373	ctl->demod = XC3028_FE_CHINA;
3374	ctl->fname = XC3028L_DEFAULT_FIRMWARE;
3375	break;
3376	default:
3377	ctl->demod = XC3028_FE_OREN538;
3378	}
3379	}
3380	EXPORT_SYMBOL_GPL(em28xx_setup_xc3028);
3381
3382	static void request_module_async(struct work_struct *work)
3383	{
3384	struct em28xx *dev = container_of(work,
3385	struct em28xx, request_module_wk);
3386
3387	/*
3388	* The em28xx extensions can be modules or builtin. If the
3389	* modules are already loaded or are built in, those extensions
3390	* can be initialised right now. Otherwise, the module init
3391	* code will do it.
3392	*/
3393
3394	/*
3395	* Devices with an audio-only intf also have a V4L/DVB/RC
3396	* intf. Don't register extensions twice on those devices.
3397	*/
3398	if (dev->is_audio_only) {
3399	#if defined(CONFIG_MODULES) && defined(MODULE)
3400	request_module("em28xx-alsa");
3401	#endif
3402	return;
3403	}
3404
3405	em28xx_init_extension(dev);
3406
3407	#if defined(CONFIG_MODULES) && defined(MODULE)
3408	if (dev->has_video)
3409	request_module("em28xx-v4l");
3410	if (dev->usb_audio_type == EM28XX_USB_AUDIO_CLASS)
3411	request_module("snd-usb-audio");
3412	else if (dev->usb_audio_type == EM28XX_USB_AUDIO_VENDOR)
3413	request_module("em28xx-alsa");
3414	if (dev->board.has_dvb)
3415	request_module("em28xx-dvb");
3416	if (dev->board.buttons ||
3417	((dev->board.ir_codes || dev->board.has_ir_i2c) && !disable_ir))
3418	request_module("em28xx-rc");
3419	#endif /* CONFIG_MODULES */
3420	}
3421
3422	static void request_modules(struct em28xx *dev)
3423	{
3424	INIT_WORK(&dev->request_module_wk, request_module_async);
3425	schedule_work(work: &dev->request_module_wk);
3426	}
3427
3428	static void flush_request_modules(struct em28xx *dev)
3429	{
3430	flush_work(work: &dev->request_module_wk);
3431	}
3432
3433	static int em28xx_media_device_init(struct em28xx *dev,
3434	struct usb_device *udev)
3435	{
3436	#ifdef CONFIG_MEDIA_CONTROLLER
3437	struct media_device *mdev;
3438
3439	mdev = kzalloc(size: sizeof(*mdev), GFP_KERNEL);
3440	if (!mdev)
3441	return -ENOMEM;
3442
3443	if (udev->product)
3444	media_device_usb_init(mdev, udev, udev->product);
3445	else if (udev->manufacturer)
3446	media_device_usb_init(mdev, udev, udev->manufacturer);
3447	else
3448	media_device_usb_init(mdev, udev, dev_name(&dev->intf->dev));
3449
3450	dev->media_dev = mdev;
3451	#endif
3452	return 0;
3453	}
3454
3455	static void em28xx_unregister_media_device(struct em28xx *dev)
3456	{
3457	#ifdef CONFIG_MEDIA_CONTROLLER
3458	if (dev->media_dev) {
3459	media_device_unregister(mdev: dev->media_dev);
3460	media_device_cleanup(mdev: dev->media_dev);
3461	kfree(objp: dev->media_dev);
3462	dev->media_dev = NULL;
3463	}
3464	#endif
3465	}
3466
3467	/*
3468	* em28xx_release_resources()
3469	* unregisters the v4l2,i2c and usb devices
3470	* called when the device gets disconnected or at module unload
3471	*/
3472	static void em28xx_release_resources(struct em28xx *dev)
3473	{
3474	struct usb_device *udev = interface_to_usbdev(dev->intf);
3475
3476	/*FIXME: I2C IR should be disconnected */
3477
3478	mutex_lock(&dev->lock);
3479
3480	em28xx_unregister_media_device(dev);
3481
3482	if (dev->def_i2c_bus)
3483	em28xx_i2c_unregister(dev, bus: 1);
3484	em28xx_i2c_unregister(dev, bus: 0);
3485
3486	if (dev->ts == PRIMARY_TS)
3487	usb_put_dev(dev: udev);
3488
3489	/* Mark device as unused */
3490	clear_bit(nr: dev->devno, addr: em28xx_devused);
3491
3492	mutex_unlock(lock: &dev->lock);
3493	};
3494
3495	/**
3496	* em28xx_free_device() - Free em28xx device
3497	*
3498	* @ref: struct kref for em28xx device
3499	*
3500	* This is called when all extensions and em28xx core unregisters a device
3501	*/
3502	void em28xx_free_device(struct kref *ref)
3503	{
3504	struct em28xx *dev = kref_to_dev(ref);
3505
3506	dev_info(&dev->intf->dev, "Freeing device\n");
3507
3508	if (!dev->disconnected)
3509	em28xx_release_resources(dev);
3510
3511	if (dev->ts == PRIMARY_TS)
3512	kfree(objp: dev->alt_max_pkt_size_isoc);
3513
3514	kfree(objp: dev);
3515	}
3516	EXPORT_SYMBOL_GPL(em28xx_free_device);
3517
3518	/*
3519	* em28xx_init_dev()
3520	* allocates and inits the device structs, registers i2c bus and v4l device
3521	*/
3522	static int em28xx_init_dev(struct em28xx *dev, struct usb_device *udev,
3523	struct usb_interface *intf,
3524	int minor)
3525	{
3526	int retval;
3527	const char *chip_name = NULL;
3528
3529	dev->intf = intf;
3530	mutex_init(&dev->ctrl_urb_lock);
3531	spin_lock_init(&dev->slock);
3532
3533	dev->em28xx_write_regs = em28xx_write_regs;
3534	dev->em28xx_read_reg = em28xx_read_reg;
3535	dev->em28xx_read_reg_req_len = em28xx_read_reg_req_len;
3536	dev->em28xx_write_regs_req = em28xx_write_regs_req;
3537	dev->em28xx_read_reg_req = em28xx_read_reg_req;
3538	dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800;
3539
3540	em28xx_set_model(dev);
3541
3542	dev->wait_after_write = 5;
3543
3544	/* Based on the Chip ID, set the device configuration */
3545	retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
3546	if (retval > 0) {
3547	dev->chip_id = retval;
3548
3549	switch (dev->chip_id) {
3550	case CHIP_ID_EM2800:
3551	chip_name = "em2800";
3552	break;
3553	case CHIP_ID_EM2710:
3554	chip_name = "em2710";
3555	break;
3556	case CHIP_ID_EM2750:
3557	chip_name = "em2750";
3558	break;
3559	case CHIP_ID_EM2765:
3560	chip_name = "em2765";
3561	dev->wait_after_write = 0;
3562	dev->is_em25xx = 1;
3563	dev->eeprom_addrwidth_16bit = 1;
3564	break;
3565	case CHIP_ID_EM2820:
3566	chip_name = "em2710/2820";
3567	if (le16_to_cpu(udev->descriptor.idVendor) == 0xeb1a) {
3568	__le16 idProd = udev->descriptor.idProduct;
3569
3570	if (le16_to_cpu(idProd) == 0x2710)
3571	chip_name = "em2710";
3572	else if (le16_to_cpu(idProd) == 0x2820)
3573	chip_name = "em2820";
3574	}
3575	/* NOTE: the em2820 is used in webcams, too ! */
3576	break;
3577	case CHIP_ID_EM2840:
3578	chip_name = "em2840";
3579	break;
3580	case CHIP_ID_EM2860:
3581	chip_name = "em2860";
3582	break;
3583	case CHIP_ID_EM2870:
3584	chip_name = "em2870";
3585	dev->wait_after_write = 0;
3586	break;
3587	case CHIP_ID_EM2874:
3588	chip_name = "em2874";
3589	dev->wait_after_write = 0;
3590	dev->eeprom_addrwidth_16bit = 1;
3591	break;
3592	case CHIP_ID_EM28174:
3593	chip_name = "em28174";
3594	dev->wait_after_write = 0;
3595	dev->eeprom_addrwidth_16bit = 1;
3596	break;
3597	case CHIP_ID_EM28178:
3598	chip_name = "em28178";
3599	dev->wait_after_write = 0;
3600	dev->eeprom_addrwidth_16bit = 1;
3601	break;
3602	case CHIP_ID_EM2883:
3603	chip_name = "em2882/3";
3604	dev->wait_after_write = 0;
3605	break;
3606	case CHIP_ID_EM2884:
3607	chip_name = "em2884";
3608	dev->wait_after_write = 0;
3609	dev->eeprom_addrwidth_16bit = 1;
3610	break;
3611	}
3612	}
3613	if (!chip_name)
3614	dev_info(&dev->intf->dev,
3615	"unknown em28xx chip ID (%d)\n", dev->chip_id);
3616	else
3617	dev_info(&dev->intf->dev, "chip ID is %s\n", chip_name);
3618
3619	em28xx_media_device_init(dev, udev);
3620
3621	if (dev->is_audio_only) {
3622	retval = em28xx_audio_setup(dev);
3623	if (retval) {
3624	retval = -ENODEV;
3625	goto err_deinit_media;
3626	}
3627	em28xx_init_extension(dev);
3628
3629	return 0;
3630	}
3631
3632	em28xx_pre_card_setup(dev);
3633
3634	rt_mutex_init(&dev->i2c_bus_lock);
3635
3636	/* register i2c bus 0 */
3637	if (dev->board.is_em2800)
3638	retval = em28xx_i2c_register(dev, bus: 0, algo_type: EM28XX_I2C_ALGO_EM2800);
3639	else
3640	retval = em28xx_i2c_register(dev, bus: 0, algo_type: EM28XX_I2C_ALGO_EM28XX);
3641	if (retval < 0) {
3642	dev_err(&dev->intf->dev,
3643	"%s: em28xx_i2c_register bus 0 - error [%d]!\n",
3644	__func__, retval);
3645	goto err_deinit_media;
3646	}
3647
3648	/* register i2c bus 1 */
3649	if (dev->def_i2c_bus) {
3650	if (dev->is_em25xx)
3651	retval = em28xx_i2c_register(dev, bus: 1,
3652	algo_type: EM28XX_I2C_ALGO_EM25XX_BUS_B);
3653	else
3654	retval = em28xx_i2c_register(dev, bus: 1,
3655	algo_type: EM28XX_I2C_ALGO_EM28XX);
3656	if (retval < 0) {
3657	dev_err(&dev->intf->dev,
3658	"%s: em28xx_i2c_register bus 1 - error [%d]!\n",
3659	__func__, retval);
3660
3661	goto err_unreg_i2c;
3662	}
3663	}
3664
3665	/* Do board specific init and eeprom reading */
3666	em28xx_card_setup(dev);
3667
3668	return 0;
3669
3670	err_unreg_i2c:
3671	em28xx_i2c_unregister(dev, bus: 0);
3672	err_deinit_media:
3673	em28xx_unregister_media_device(dev);
3674	return retval;
3675	}
3676
3677	static int em28xx_duplicate_dev(struct em28xx *dev)
3678	{
3679	int nr;
3680	struct em28xx *sec_dev = kmemdup(p: dev, size: sizeof(*sec_dev), GFP_KERNEL);
3681
3682	if (!sec_dev) {
3683	dev->dev_next = NULL;
3684	return -ENOMEM;
3685	}
3686	/* Check to see next free device and mark as used */
3687	do {
3688	nr = find_first_zero_bit(addr: em28xx_devused, EM28XX_MAXBOARDS);
3689	if (nr >= EM28XX_MAXBOARDS) {
3690	/* No free device slots */
3691	dev_warn(&dev->intf->dev, ": Supports only %i em28xx boards.\n",
3692	EM28XX_MAXBOARDS);
3693	kfree(objp: sec_dev);
3694	dev->dev_next = NULL;
3695	return -ENOMEM;
3696	}
3697	} while (test_and_set_bit(nr, addr: em28xx_devused));
3698	sec_dev->devno = nr;
3699	snprintf(buf: sec_dev->name, size: 28, fmt: "em28xx #%d", nr);
3700	sec_dev->dev_next = NULL;
3701	dev->dev_next = sec_dev;
3702	return 0;
3703	}
3704
3705	/* high bandwidth multiplier, as encoded in highspeed endpoint descriptors */
3706	#define hb_mult(wMaxPacketSize) (1 + (((wMaxPacketSize) >> 11) & 0x03))
3707
3708	static void em28xx_check_usb_descriptor(struct em28xx *dev,
3709	struct usb_device *udev,
3710	struct usb_interface *intf,
3711	int alt, int ep,
3712	bool *has_vendor_audio,
3713	bool *has_video,
3714	bool *has_dvb)
3715	{
3716	const struct usb_endpoint_descriptor *e;
3717	int sizedescr, size;
3718
3719	/*
3720	* NOTE:
3721	*
3722	* Old logic with support for isoc transfers only was:
3723	* 0x82 isoc => analog
3724	* 0x83 isoc => audio
3725	* 0x84 isoc => digital
3726	*
3727	* New logic with support for bulk transfers
3728	* 0x82 isoc => analog
3729	* 0x82 bulk => analog
3730	* 0x83 isoc* => audio
3731	* 0x84 isoc => digital
3732	* 0x84 bulk => analog or digital**
3733	* 0x85 isoc => digital TS2
3734	* 0x85 bulk => digital TS2
3735	* (*: audio should always be isoc)
3736	* (**: analog, if ep 0x82 is isoc, otherwise digital)
3737	*
3738	* The new logic preserves backwards compatibility and
3739	* reflects the endpoint configurations we have seen
3740	* so far. But there might be devices for which this
3741	* logic is not sufficient...
3742	*/
3743
3744	e = &intf->altsetting[alt].endpoint[ep].desc;
3745
3746	if (!usb_endpoint_dir_in(epd: e))
3747	return;
3748
3749	sizedescr = le16_to_cpu(e->wMaxPacketSize);
3750	size = sizedescr & 0x7ff;
3751
3752	if (udev->speed == USB_SPEED_HIGH)
3753	size = size * hb_mult(sizedescr);
3754
3755	/* Only inspect input endpoints */
3756
3757	switch (e->bEndpointAddress) {
3758	case 0x82:
3759	*has_video = true;
3760	if (usb_endpoint_xfer_isoc(epd: e)) {
3761	dev->analog_ep_isoc = e->bEndpointAddress;
3762	dev->alt_max_pkt_size_isoc[alt] = size;
3763	} else if (usb_endpoint_xfer_bulk(epd: e)) {
3764	dev->analog_ep_bulk = e->bEndpointAddress;
3765	}
3766	return;
3767	case 0x83:
3768	if (usb_endpoint_xfer_isoc(epd: e))
3769	*has_vendor_audio = true;
3770	else
3771	dev_err(&intf->dev,
3772	"error: skipping audio endpoint 0x83, because it uses bulk transfers !\n");
3773	return;
3774	case 0x84:
3775	if (*has_video && (usb_endpoint_xfer_bulk(epd: e))) {
3776	dev->analog_ep_bulk = e->bEndpointAddress;
3777	} else {
3778	if (usb_endpoint_xfer_isoc(epd: e)) {
3779	if (size > dev->dvb_max_pkt_size_isoc) {
3780	/*
3781	* 2) some manufacturers (e.g. Terratec)
3782	* disable endpoints by setting
3783	* wMaxPacketSize to 0 bytes for all
3784	* alt settings. So far, we've seen
3785	* this for DVB isoc endpoints only.
3786	*/
3787	*has_dvb = true;
3788	dev->dvb_ep_isoc = e->bEndpointAddress;
3789	dev->dvb_max_pkt_size_isoc = size;
3790	dev->dvb_alt_isoc = alt;
3791	}
3792	} else {
3793	*has_dvb = true;
3794	dev->dvb_ep_bulk = e->bEndpointAddress;
3795	}
3796	}
3797	return;
3798	case 0x85:
3799	if (usb_endpoint_xfer_isoc(epd: e)) {
3800	if (size > dev->dvb_max_pkt_size_isoc_ts2) {
3801	dev->dvb_ep_isoc_ts2 = e->bEndpointAddress;
3802	dev->dvb_max_pkt_size_isoc_ts2 = size;
3803	dev->dvb_alt_isoc = alt;
3804	}
3805	} else {
3806	dev->dvb_ep_bulk_ts2 = e->bEndpointAddress;
3807	}
3808	return;
3809	}
3810	}
3811
3812	/*
3813	* em28xx_usb_probe()
3814	* checks for supported devices
3815	*/
3816	static int em28xx_usb_probe(struct usb_interface *intf,
3817	const struct usb_device_id *id)
3818	{
3819	struct usb_device *udev;
3820	struct em28xx *dev = NULL;
3821	int retval;
3822	bool has_vendor_audio = false, has_video = false, has_dvb = false;
3823	int i, nr, try_bulk;
3824	const int ifnum = intf->altsetting[0].desc.bInterfaceNumber;
3825	char *speed;
3826
3827	udev = usb_get_dev(interface_to_usbdev(intf));
3828
3829	/* Check to see next free device and mark as used */
3830	do {
3831	nr = find_first_zero_bit(addr: em28xx_devused, EM28XX_MAXBOARDS);
3832	if (nr >= EM28XX_MAXBOARDS) {
3833	/* No free device slots */
3834	dev_err(&intf->dev,
3835	"Driver supports up to %i em28xx boards.\n",
3836	EM28XX_MAXBOARDS);
3837	retval = -ENOMEM;
3838	goto err_no_slot;
3839	}
3840	} while (test_and_set_bit(nr, addr: em28xx_devused));
3841
3842	/* Don't register audio interfaces */
3843	if (intf->altsetting[0].desc.bInterfaceClass == USB_CLASS_AUDIO) {
3844	dev_info(&intf->dev,
3845	"audio device (%04x:%04x): interface %i, class %i\n",
3846	le16_to_cpu(udev->descriptor.idVendor),
3847	le16_to_cpu(udev->descriptor.idProduct),
3848	ifnum,
3849	intf->altsetting[0].desc.bInterfaceClass);
3850
3851	retval = -ENODEV;
3852	goto err;
3853	}
3854
3855	/* allocate memory for our device state and initialize it */
3856	dev = kzalloc(size: sizeof(*dev), GFP_KERNEL);
3857	if (!dev) {
3858	retval = -ENOMEM;
3859	goto err;
3860	}
3861
3862	/* compute alternate max packet sizes */
3863	dev->alt_max_pkt_size_isoc = kcalloc(n: intf->num_altsetting,
3864	size: sizeof(dev->alt_max_pkt_size_isoc[0]),
3865	GFP_KERNEL);
3866	if (!dev->alt_max_pkt_size_isoc) {
3867	kfree(objp: dev);
3868	retval = -ENOMEM;
3869	goto err;
3870	}
3871
3872	/* Get endpoints */
3873	for (i = 0; i < intf->num_altsetting; i++) {
3874	int ep;
3875
3876	for (ep = 0;
3877	ep < intf->altsetting[i].desc.bNumEndpoints;
3878	ep++)
3879	em28xx_check_usb_descriptor(dev, udev, intf,
3880	alt: i, ep,
3881	has_vendor_audio: &has_vendor_audio,
3882	has_video: &has_video,
3883	has_dvb: &has_dvb);
3884	}
3885
3886	if (!(has_vendor_audio || has_video || has_dvb)) {
3887	retval = -ENODEV;
3888	goto err_free;
3889	}
3890
3891	switch (udev->speed) {
3892	case USB_SPEED_LOW:
3893	speed = "1.5";
3894	break;
3895	case USB_SPEED_UNKNOWN:
3896	case USB_SPEED_FULL:
3897	speed = "12";
3898	break;
3899	case USB_SPEED_HIGH:
3900	speed = "480";
3901	break;
3902	default:
3903	speed = "unknown";
3904	}
3905
3906	dev_info(&intf->dev,
3907	"New device %s %s @ %s Mbps (%04x:%04x, interface %d, class %d)\n",
3908	udev->manufacturer ? udev->manufacturer : "",
3909	udev->product ? udev->product : "",
3910	speed,
3911	le16_to_cpu(udev->descriptor.idVendor),
3912	le16_to_cpu(udev->descriptor.idProduct),
3913	ifnum,
3914	intf->altsetting->desc.bInterfaceNumber);
3915
3916	/*
3917	* Make sure we have 480 Mbps of bandwidth, otherwise things like
3918	* video stream wouldn't likely work, since 12 Mbps is generally
3919	* not enough even for most Digital TV streams.
3920	*/
3921	if (udev->speed != USB_SPEED_HIGH && disable_usb_speed_check == 0) {
3922	dev_err(&intf->dev, "Device initialization failed.\n");
3923	dev_err(&intf->dev,
3924	"Device must be connected to a high-speed USB 2.0 port.\n");
3925	retval = -ENODEV;
3926	goto err_free;
3927	}
3928
3929	kref_init(kref: &dev->ref);
3930
3931	dev->devno = nr;
3932	dev->model = id->driver_info;
3933	dev->alt = -1;
3934	dev->is_audio_only = has_vendor_audio && !(has_video || has_dvb);
3935	dev->has_video = has_video;
3936	dev->ifnum = ifnum;
3937
3938	dev->ts = PRIMARY_TS;
3939	snprintf(buf: dev->name, size: 28, fmt: "em28xx");
3940	dev->dev_next = NULL;
3941
3942	if (has_vendor_audio) {
3943	dev_info(&intf->dev,
3944	"Audio interface %i found (Vendor Class)\n", ifnum);
3945	dev->usb_audio_type = EM28XX_USB_AUDIO_VENDOR;
3946	}
3947	/* Checks if audio is provided by a USB Audio Class intf */
3948	for (i = 0; i < udev->config->desc.bNumInterfaces; i++) {
3949	struct usb_interface *uif = udev->config->interface[i];
3950
3951	if (uif->altsetting[0].desc.bInterfaceClass == USB_CLASS_AUDIO) {
3952	if (has_vendor_audio)
3953	dev_err(&intf->dev,
3954	"em28xx: device seems to have vendor AND usb audio class interfaces !\n"
3955	"\t\tThe vendor interface will be ignored. Please contact the developers <linux-media@vger.kernel.org>\n");
3956	dev->usb_audio_type = EM28XX_USB_AUDIO_CLASS;
3957	break;
3958	}
3959	}
3960
3961	if (has_video)
3962	dev_info(&intf->dev, "Video interface %i found:%s%s\n",
3963	ifnum,
3964	dev->analog_ep_bulk ? " bulk" : "",
3965	dev->analog_ep_isoc ? " isoc" : "");
3966	if (has_dvb)
3967	dev_info(&intf->dev, "DVB interface %i found:%s%s\n",
3968	ifnum,
3969	dev->dvb_ep_bulk ? " bulk" : "",
3970	dev->dvb_ep_isoc ? " isoc" : "");
3971
3972	dev->num_alt = intf->num_altsetting;
3973
3974	if ((unsigned int)card[nr] < em28xx_bcount)
3975	dev->model = card[nr];
3976
3977	/* save our data pointer in this intf device */
3978	usb_set_intfdata(intf, data: dev);
3979
3980	/* allocate device struct and check if the device is a webcam */
3981	mutex_init(&dev->lock);
3982	retval = em28xx_init_dev(dev, udev, intf, minor: nr);
3983	if (retval)
3984	goto err_free;
3985
3986	if (usb_xfer_mode < 0) {
3987	if (dev->is_webcam)
3988	try_bulk = 1;
3989	else
3990	try_bulk = 0;
3991	} else {
3992	try_bulk = usb_xfer_mode > 0;
3993	}
3994
3995	/* Disable V4L2 if the device doesn't have a decoder or image sensor */
3996	if (has_video &&
3997	dev->board.decoder == EM28XX_NODECODER &&
3998	dev->em28xx_sensor == EM28XX_NOSENSOR) {
3999	dev_err(&intf->dev,
4000	"Currently, V4L2 is not supported on this model\n");
4001	has_video = false;
4002	dev->has_video = false;
4003	}
4004
4005	if (dev->board.has_dual_ts &&
4006	(dev->tuner_type != TUNER_ABSENT || INPUT(0)->type)) {
4007	/*
4008	* The logic with sets alternate is not ready for dual-tuners
4009	* which analog modes.
4010	*/
4011	dev_err(&intf->dev,
4012	"We currently don't support analog TV or stream capture on dual tuners.\n");
4013	has_video = false;
4014	}
4015
4016	/* Select USB transfer types to use */
4017	if (has_video) {
4018	if (!dev->analog_ep_isoc || (try_bulk && dev->analog_ep_bulk))
4019	dev->analog_xfer_bulk = 1;
4020	dev_info(&intf->dev, "analog set to %s mode.\n",
4021	dev->analog_xfer_bulk ? "bulk" : "isoc");
4022	}
4023	if (has_dvb) {
4024	if (!dev->dvb_ep_isoc || (try_bulk && dev->dvb_ep_bulk))
4025	dev->dvb_xfer_bulk = 1;
4026	dev_info(&intf->dev, "dvb set to %s mode.\n",
4027	dev->dvb_xfer_bulk ? "bulk" : "isoc");
4028	}
4029
4030	if (dev->board.has_dual_ts && em28xx_duplicate_dev(dev) == 0) {
4031	kref_init(kref: &dev->dev_next->ref);
4032
4033	dev->dev_next->ts = SECONDARY_TS;
4034	dev->dev_next->alt = -1;
4035	dev->dev_next->is_audio_only = has_vendor_audio &&
4036	!(has_video || has_dvb);
4037	dev->dev_next->has_video = false;
4038	dev->dev_next->ifnum = ifnum;
4039	dev->dev_next->model = id->driver_info;
4040
4041	mutex_init(&dev->dev_next->lock);
4042	retval = em28xx_init_dev(dev: dev->dev_next, udev, intf,
4043	minor: dev->dev_next->devno);
4044	if (retval)
4045	goto err_free;
4046
4047	dev->dev_next->board.ir_codes = NULL; /* No IR for 2nd tuner */
4048	dev->dev_next->board.has_ir_i2c = 0; /* No IR for 2nd tuner */
4049
4050	if (usb_xfer_mode < 0) {
4051	if (dev->dev_next->is_webcam)
4052	try_bulk = 1;
4053	else
4054	try_bulk = 0;
4055	} else {
4056	try_bulk = usb_xfer_mode > 0;
4057	}
4058
4059	/* Select USB transfer types to use */
4060	if (has_dvb) {
4061	if (!dev->dvb_ep_isoc_ts2 ||
4062	(try_bulk && dev->dvb_ep_bulk_ts2))
4063	dev->dev_next->dvb_xfer_bulk = 1;
4064	dev_info(&dev->intf->dev, "dvb ts2 set to %s mode.\n",
4065	dev->dev_next->dvb_xfer_bulk ? "bulk" : "isoc");
4066	}
4067
4068	dev->dev_next->dvb_ep_isoc = dev->dvb_ep_isoc_ts2;
4069	dev->dev_next->dvb_ep_bulk = dev->dvb_ep_bulk_ts2;
4070	dev->dev_next->dvb_max_pkt_size_isoc = dev->dvb_max_pkt_size_isoc_ts2;
4071	dev->dev_next->dvb_alt_isoc = dev->dvb_alt_isoc;
4072
4073	/* Configure hardware to support TS2*/
4074	if (dev->dvb_xfer_bulk) {
4075	/* The ep4 and ep5 are configured for BULK */
4076	em28xx_write_reg(dev, reg: 0x0b, val: 0x96);
4077	mdelay(100);
4078	em28xx_write_reg(dev, reg: 0x0b, val: 0x80);
4079	mdelay(100);
4080	} else {
4081	/* The ep4 and ep5 are configured for ISO */
4082	em28xx_write_reg(dev, reg: 0x0b, val: 0x96);
4083	mdelay(100);
4084	em28xx_write_reg(dev, reg: 0x0b, val: 0x82);
4085	mdelay(100);
4086	}
4087	}
4088
4089	request_modules(dev);
4090
4091	/*
4092	* Do it at the end, to reduce dynamic configuration changes during
4093	* the device init. Yet, as request_modules() can be async, the
4094	* topology will likely change after the load of the em28xx subdrivers.
4095	*/
4096	#ifdef CONFIG_MEDIA_CONTROLLER
4097	/*
4098	* No need to check the return value, the device will still be
4099	* usable without media controller API.
4100	*/
4101	retval = media_device_register(dev->media_dev);
4102	#endif
4103
4104	return 0;
4105
4106	err_free:
4107	kfree(objp: dev->alt_max_pkt_size_isoc);
4108	kfree(objp: dev);
4109
4110	err:
4111	clear_bit(nr, addr: em28xx_devused);
4112
4113	err_no_slot:
4114	usb_put_dev(dev: udev);
4115	return retval;
4116	}
4117
4118	/*
4119	* em28xx_usb_disconnect()
4120	* called when the device gets disconnected
4121	* video device will be unregistered on v4l2_close in case it is still open
4122	*/
4123	static void em28xx_usb_disconnect(struct usb_interface *intf)
4124	{
4125	struct em28xx *dev;
4126
4127	dev = usb_get_intfdata(intf);
4128	usb_set_intfdata(intf, NULL);
4129
4130	if (!dev)
4131	return;
4132
4133	if (dev->dev_next) {
4134	dev->dev_next->disconnected = 1;
4135	dev_info(&dev->intf->dev, "Disconnecting %s\n",
4136	dev->dev_next->name);
4137	}
4138
4139	dev->disconnected = 1;
4140
4141	dev_info(&dev->intf->dev, "Disconnecting %s\n", dev->name);
4142
4143	flush_request_modules(dev);
4144
4145	em28xx_close_extension(dev);
4146
4147	if (dev->dev_next)
4148	em28xx_release_resources(dev: dev->dev_next);
4149	em28xx_release_resources(dev);
4150
4151	if (dev->dev_next) {
4152	kref_put(kref: &dev->dev_next->ref, release: em28xx_free_device);
4153	dev->dev_next = NULL;
4154	}
4155	kref_put(kref: &dev->ref, release: em28xx_free_device);
4156	}
4157
4158	static int em28xx_usb_suspend(struct usb_interface *intf,
4159	pm_message_t message)
4160	{
4161	struct em28xx *dev;
4162
4163	dev = usb_get_intfdata(intf);
4164	if (!dev)
4165	return 0;
4166	em28xx_suspend_extension(dev);
4167	return 0;
4168	}
4169
4170	static int em28xx_usb_resume(struct usb_interface *intf)
4171	{
4172	struct em28xx *dev;
4173
4174	dev = usb_get_intfdata(intf);
4175	if (!dev)
4176	return 0;
4177	em28xx_resume_extension(dev);
4178	return 0;
4179	}
4180
4181	static struct usb_driver em28xx_usb_driver = {
4182	.name = "em28xx",
4183	.probe = em28xx_usb_probe,
4184	.disconnect = em28xx_usb_disconnect,
4185	.suspend = em28xx_usb_suspend,
4186	.resume = em28xx_usb_resume,
4187	.reset_resume = em28xx_usb_resume,
4188	.id_table = em28xx_id_table,
4189	};
4190
4191	module_usb_driver(em28xx_usb_driver);
4192