1 | // SPDX-License-Identifier: GPL-2.0 |
---|---|
2 | /* |
3 | * ARC On-Chip(fpga) UART Driver |
4 | * |
5 | * Copyright (C) 2010-2012 Synopsys, Inc. (www.synopsys.com) |
6 | * |
7 | * vineetg: July 10th 2012 |
8 | * -Decoupled the driver from arch/arc |
9 | * +Using platform_get_resource() for irq/membase (thx to bfin_uart.c) |
10 | * +Using early_platform_xxx() for early console (thx to mach-shmobile/xxx) |
11 | * |
12 | * Vineetg: Aug 21st 2010 |
13 | * -Is uart_tx_stopped() not done in tty write path as it has already been |
14 | * taken care of, in serial core |
15 | * |
16 | * Vineetg: Aug 18th 2010 |
17 | * -New Serial Core based ARC UART driver |
18 | * -Derived largely from blackfin driver albiet with some major tweaks |
19 | * |
20 | * TODO: |
21 | * -check if sysreq works |
22 | */ |
23 | |
24 | #include <linux/module.h> |
25 | #include <linux/serial.h> |
26 | #include <linux/console.h> |
27 | #include <linux/sysrq.h> |
28 | #include <linux/platform_device.h> |
29 | #include <linux/tty.h> |
30 | #include <linux/tty_flip.h> |
31 | #include <linux/serial_core.h> |
32 | #include <linux/io.h> |
33 | #include <linux/of_irq.h> |
34 | #include <linux/of_address.h> |
35 | |
36 | /************************************* |
37 | * ARC UART Hardware Specs |
38 | ************************************/ |
39 | #define ARC_UART_TX_FIFO_SIZE 1 |
40 | |
41 | /* |
42 | * UART Register set (this is not a Standards Compliant IP) |
43 | * Also each reg is Word aligned, but only 8 bits wide |
44 | */ |
45 | #define R_ID0 0 |
46 | #define R_ID1 4 |
47 | #define R_ID2 8 |
48 | #define R_ID3 12 |
49 | #define R_DATA 16 |
50 | #define R_STS 20 |
51 | #define R_BAUDL 24 |
52 | #define R_BAUDH 28 |
53 | |
54 | /* Bits for UART Status Reg (R/W) */ |
55 | #define RXIENB 0x04 /* Receive Interrupt Enable */ |
56 | #define TXIENB 0x40 /* Transmit Interrupt Enable */ |
57 | |
58 | #define RXEMPTY 0x20 /* Receive FIFO Empty: No char receivede */ |
59 | #define TXEMPTY 0x80 /* Transmit FIFO Empty, thus char can be written into */ |
60 | |
61 | #define RXFULL 0x08 /* Receive FIFO full */ |
62 | #define RXFULL1 0x10 /* Receive FIFO has space for 1 char (tot space=4) */ |
63 | |
64 | #define RXFERR 0x01 /* Frame Error: Stop Bit not detected */ |
65 | #define RXOERR 0x02 /* OverFlow Err: Char recv but RXFULL still set */ |
66 | |
67 | /* Uart bit fiddling helpers: lowest level */ |
68 | #define RBASE(port, reg) (port->membase + reg) |
69 | #define UART_REG_SET(u, r, v) writeb((v), RBASE(u, r)) |
70 | #define UART_REG_GET(u, r) readb(RBASE(u, r)) |
71 | |
72 | #define UART_REG_OR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) | (v)) |
73 | #define UART_REG_CLR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) & ~(v)) |
74 | |
75 | /* Uart bit fiddling helpers: API level */ |
76 | #define UART_SET_DATA(uart, val) UART_REG_SET(uart, R_DATA, val) |
77 | #define UART_GET_DATA(uart) UART_REG_GET(uart, R_DATA) |
78 | |
79 | #define UART_SET_BAUDH(uart, val) UART_REG_SET(uart, R_BAUDH, val) |
80 | #define UART_SET_BAUDL(uart, val) UART_REG_SET(uart, R_BAUDL, val) |
81 | |
82 | #define UART_CLR_STATUS(uart, val) UART_REG_CLR(uart, R_STS, val) |
83 | #define UART_GET_STATUS(uart) UART_REG_GET(uart, R_STS) |
84 | |
85 | #define UART_ALL_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB|TXIENB) |
86 | #define UART_RX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB) |
87 | #define UART_TX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, TXIENB) |
88 | |
89 | #define UART_ALL_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB|TXIENB) |
90 | #define UART_RX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB) |
91 | #define UART_TX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, TXIENB) |
92 | |
93 | #define ARC_SERIAL_DEV_NAME "ttyARC" |
94 | |
95 | struct arc_uart_port { |
96 | struct uart_port port; |
97 | unsigned long baud; |
98 | }; |
99 | |
100 | #define to_arc_port(uport) container_of(uport, struct arc_uart_port, port) |
101 | |
102 | static struct arc_uart_port arc_uart_ports[CONFIG_SERIAL_ARC_NR_PORTS]; |
103 | |
104 | #ifdef CONFIG_SERIAL_ARC_CONSOLE |
105 | static struct console arc_console; |
106 | #endif |
107 | |
108 | #define DRIVER_NAME "arc-uart" |
109 | |
110 | static struct uart_driver arc_uart_driver = { |
111 | .owner = THIS_MODULE, |
112 | .driver_name = DRIVER_NAME, |
113 | .dev_name = ARC_SERIAL_DEV_NAME, |
114 | .major = 0, |
115 | .minor = 0, |
116 | .nr = CONFIG_SERIAL_ARC_NR_PORTS, |
117 | #ifdef CONFIG_SERIAL_ARC_CONSOLE |
118 | .cons = &arc_console, |
119 | #endif |
120 | }; |
121 | |
122 | static void arc_serial_stop_rx(struct uart_port *port) |
123 | { |
124 | UART_RX_IRQ_DISABLE(port); |
125 | } |
126 | |
127 | static void arc_serial_stop_tx(struct uart_port *port) |
128 | { |
129 | while (!(UART_GET_STATUS(port) & TXEMPTY)) |
130 | cpu_relax(); |
131 | |
132 | UART_TX_IRQ_DISABLE(port); |
133 | } |
134 | |
135 | /* |
136 | * Return TIOCSER_TEMT when transmitter is not busy. |
137 | */ |
138 | static unsigned int arc_serial_tx_empty(struct uart_port *port) |
139 | { |
140 | unsigned int stat; |
141 | |
142 | stat = UART_GET_STATUS(port); |
143 | if (stat & TXEMPTY) |
144 | return TIOCSER_TEMT; |
145 | |
146 | return 0; |
147 | } |
148 | |
149 | /* |
150 | * Driver internal routine, used by both tty(serial core) as well as tx-isr |
151 | * -Called under spinlock in either cases |
152 | * -also tty->flow.stopped has already been checked |
153 | * = by uart_start( ) before calling us |
154 | * = tx_ist checks that too before calling |
155 | */ |
156 | static void arc_serial_tx_chars(struct uart_port *port) |
157 | { |
158 | struct tty_port *tport = &port->state->port; |
159 | int sent = 0; |
160 | unsigned char ch; |
161 | |
162 | if (unlikely(port->x_char)) { |
163 | UART_SET_DATA(port, port->x_char); |
164 | port->icount.tx++; |
165 | port->x_char = 0; |
166 | sent = 1; |
167 | } else if (uart_fifo_get(up: port, ch: &ch)) { |
168 | while (!(UART_GET_STATUS(port) & TXEMPTY)) |
169 | cpu_relax(); |
170 | UART_SET_DATA(port, ch); |
171 | sent = 1; |
172 | } |
173 | |
174 | /* |
175 | * If num chars in xmit buffer are too few, ask tty layer for more. |
176 | * By Hard ISR to schedule processing in software interrupt part |
177 | */ |
178 | if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) |
179 | uart_write_wakeup(port); |
180 | |
181 | if (sent) |
182 | UART_TX_IRQ_ENABLE(port); |
183 | } |
184 | |
185 | /* |
186 | * port is locked and interrupts are disabled |
187 | * uart_start( ) calls us under the port spinlock irqsave |
188 | */ |
189 | static void arc_serial_start_tx(struct uart_port *port) |
190 | { |
191 | arc_serial_tx_chars(port); |
192 | } |
193 | |
194 | static void arc_serial_rx_chars(struct uart_port *port, unsigned int status) |
195 | { |
196 | /* |
197 | * UART has 4 deep RX-FIFO. Driver's recongnition of this fact |
198 | * is very subtle. Here's how ... |
199 | * Upon getting a RX-Intr, such that RX-EMPTY=0, meaning data available, |
200 | * driver reads the DATA Reg and keeps doing that in a loop, until |
201 | * RX-EMPTY=1. Multiple chars being avail, with a single Interrupt, |
202 | * before RX-EMPTY=0, implies some sort of buffering going on in the |
203 | * controller, which is indeed the Rx-FIFO. |
204 | */ |
205 | do { |
206 | u8 ch, flg = TTY_NORMAL; |
207 | |
208 | /* |
209 | * This could be an Rx Intr for err (no data), |
210 | * so check err and clear that Intr first |
211 | */ |
212 | if (status & RXOERR) { |
213 | port->icount.overrun++; |
214 | flg = TTY_OVERRUN; |
215 | UART_CLR_STATUS(port, RXOERR); |
216 | } |
217 | |
218 | if (status & RXFERR) { |
219 | port->icount.frame++; |
220 | flg = TTY_FRAME; |
221 | UART_CLR_STATUS(port, RXFERR); |
222 | } |
223 | |
224 | if (status & RXEMPTY) |
225 | continue; |
226 | |
227 | ch = UART_GET_DATA(port); |
228 | port->icount.rx++; |
229 | |
230 | if (!(uart_handle_sysrq_char(port, ch))) |
231 | uart_insert_char(port, status, RXOERR, ch, flag: flg); |
232 | |
233 | tty_flip_buffer_push(port: &port->state->port); |
234 | } while (!((status = UART_GET_STATUS(port)) & RXEMPTY)); |
235 | } |
236 | |
237 | /* |
238 | * A note on the Interrupt handling state machine of this driver |
239 | * |
240 | * kernel printk writes funnel thru the console driver framework and in order |
241 | * to keep things simple as well as efficient, it writes to UART in polled |
242 | * mode, in one shot, and exits. |
243 | * |
244 | * OTOH, Userland output (via tty layer), uses interrupt based writes as there |
245 | * can be undeterministic delay between char writes. |
246 | * |
247 | * Thus Rx-interrupts are always enabled, while tx-interrupts are by default |
248 | * disabled. |
249 | * |
250 | * When tty has some data to send out, serial core calls driver's start_tx |
251 | * which |
252 | * -checks-if-tty-buffer-has-char-to-send |
253 | * -writes-data-to-uart |
254 | * -enable-tx-intr |
255 | * |
256 | * Once data bits are pushed out, controller raises the Tx-room-avail-Interrupt. |
257 | * The first thing Tx ISR does is disable further Tx interrupts (as this could |
258 | * be the last char to send, before settling down into the quiet polled mode). |
259 | * It then calls the exact routine used by tty layer write to send out any |
260 | * more char in tty buffer. In case of sending, it re-enables Tx-intr. In case |
261 | * of no data, it remains disabled. |
262 | * This is how the transmit state machine is dynamically switched on/off |
263 | */ |
264 | |
265 | static irqreturn_t arc_serial_isr(int irq, void *dev_id) |
266 | { |
267 | struct uart_port *port = dev_id; |
268 | unsigned int status; |
269 | |
270 | status = UART_GET_STATUS(port); |
271 | |
272 | /* |
273 | * Single IRQ for both Rx (data available) Tx (room available) Interrupt |
274 | * notifications from the UART Controller. |
275 | * To demultiplex between the two, we check the relevant bits |
276 | */ |
277 | if (status & RXIENB) { |
278 | |
279 | /* already in ISR, no need of xx_irqsave */ |
280 | uart_port_lock(up: port); |
281 | arc_serial_rx_chars(port, status); |
282 | uart_port_unlock(up: port); |
283 | } |
284 | |
285 | if ((status & TXIENB) && (status & TXEMPTY)) { |
286 | |
287 | /* Unconditionally disable further Tx-Interrupts. |
288 | * will be enabled by tx_chars() if needed. |
289 | */ |
290 | UART_TX_IRQ_DISABLE(port); |
291 | |
292 | uart_port_lock(up: port); |
293 | |
294 | if (!uart_tx_stopped(port)) |
295 | arc_serial_tx_chars(port); |
296 | |
297 | uart_port_unlock(up: port); |
298 | } |
299 | |
300 | return IRQ_HANDLED; |
301 | } |
302 | |
303 | static unsigned int arc_serial_get_mctrl(struct uart_port *port) |
304 | { |
305 | /* |
306 | * Pretend we have a Modem status reg and following bits are |
307 | * always set, to satify the serial core state machine |
308 | * (DSR) Data Set Ready |
309 | * (CTS) Clear To Send |
310 | * (CAR) Carrier Detect |
311 | */ |
312 | return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; |
313 | } |
314 | |
315 | static void arc_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) |
316 | { |
317 | /* MCR not present */ |
318 | } |
319 | |
320 | static void arc_serial_break_ctl(struct uart_port *port, int break_state) |
321 | { |
322 | /* ARC UART doesn't support sending Break signal */ |
323 | } |
324 | |
325 | static int arc_serial_startup(struct uart_port *port) |
326 | { |
327 | /* Before we hook up the ISR, Disable all UART Interrupts */ |
328 | UART_ALL_IRQ_DISABLE(port); |
329 | |
330 | if (request_irq(irq: port->irq, handler: arc_serial_isr, flags: 0, name: "arc uart rx-tx", dev: port)) { |
331 | dev_warn(port->dev, "Unable to attach ARC UART intr\n"); |
332 | return -EBUSY; |
333 | } |
334 | |
335 | UART_RX_IRQ_ENABLE(port); /* Only Rx IRQ enabled to begin with */ |
336 | |
337 | return 0; |
338 | } |
339 | |
340 | /* This is not really needed */ |
341 | static void arc_serial_shutdown(struct uart_port *port) |
342 | { |
343 | free_irq(port->irq, port); |
344 | } |
345 | |
346 | static void |
347 | arc_serial_set_termios(struct uart_port *port, struct ktermios *new, |
348 | const struct ktermios *old) |
349 | { |
350 | struct arc_uart_port *uart = to_arc_port(port); |
351 | unsigned int baud, uartl, uarth, hw_val; |
352 | unsigned long flags; |
353 | |
354 | /* |
355 | * Use the generic handler so that any specially encoded baud rates |
356 | * such as SPD_xx flags or "%B0" can be handled |
357 | * Max Baud I suppose will not be more than current 115K * 4 |
358 | * Formula for ARC UART is: hw-val = ((CLK/(BAUD*4)) -1) |
359 | * spread over two 8-bit registers |
360 | */ |
361 | baud = uart_get_baud_rate(port, termios: new, old, min: 0, max: 460800); |
362 | |
363 | hw_val = port->uartclk / (uart->baud * 4) - 1; |
364 | uartl = hw_val & 0xFF; |
365 | uarth = (hw_val >> 8) & 0xFF; |
366 | |
367 | uart_port_lock_irqsave(up: port, flags: &flags); |
368 | |
369 | UART_ALL_IRQ_DISABLE(port); |
370 | |
371 | UART_SET_BAUDL(port, uartl); |
372 | UART_SET_BAUDH(port, uarth); |
373 | |
374 | UART_RX_IRQ_ENABLE(port); |
375 | |
376 | /* |
377 | * UART doesn't support Parity/Hardware Flow Control; |
378 | * Only supports 8N1 character size |
379 | */ |
380 | new->c_cflag &= ~(CMSPAR|CRTSCTS|CSIZE); |
381 | new->c_cflag |= CS8; |
382 | |
383 | if (old) |
384 | tty_termios_copy_hw(new, old); |
385 | |
386 | /* Don't rewrite B0 */ |
387 | if (tty_termios_baud_rate(termios: new)) |
388 | tty_termios_encode_baud_rate(termios: new, ibaud: baud, obaud: baud); |
389 | |
390 | uart_update_timeout(port, cflag: new->c_cflag, baud); |
391 | |
392 | uart_port_unlock_irqrestore(up: port, flags); |
393 | } |
394 | |
395 | static const char *arc_serial_type(struct uart_port *port) |
396 | { |
397 | return port->type == PORT_ARC ? DRIVER_NAME : NULL; |
398 | } |
399 | |
400 | static void arc_serial_release_port(struct uart_port *port) |
401 | { |
402 | } |
403 | |
404 | static int arc_serial_request_port(struct uart_port *port) |
405 | { |
406 | return 0; |
407 | } |
408 | |
409 | /* |
410 | * Verify the new serial_struct (for TIOCSSERIAL). |
411 | */ |
412 | static int |
413 | arc_serial_verify_port(struct uart_port *port, struct serial_struct *ser) |
414 | { |
415 | if (port->type != PORT_UNKNOWN && ser->type != PORT_ARC) |
416 | return -EINVAL; |
417 | |
418 | return 0; |
419 | } |
420 | |
421 | /* |
422 | * Configure/autoconfigure the port. |
423 | */ |
424 | static void arc_serial_config_port(struct uart_port *port, int flags) |
425 | { |
426 | if (flags & UART_CONFIG_TYPE) |
427 | port->type = PORT_ARC; |
428 | } |
429 | |
430 | #ifdef CONFIG_CONSOLE_POLL |
431 | |
432 | static void arc_serial_poll_putchar(struct uart_port *port, unsigned char chr) |
433 | { |
434 | while (!(UART_GET_STATUS(port) & TXEMPTY)) |
435 | cpu_relax(); |
436 | |
437 | UART_SET_DATA(port, chr); |
438 | } |
439 | |
440 | static int arc_serial_poll_getchar(struct uart_port *port) |
441 | { |
442 | unsigned char chr; |
443 | |
444 | while (!(UART_GET_STATUS(port) & RXEMPTY)) |
445 | cpu_relax(); |
446 | |
447 | chr = UART_GET_DATA(port); |
448 | return chr; |
449 | } |
450 | #endif |
451 | |
452 | static const struct uart_ops arc_serial_pops = { |
453 | .tx_empty = arc_serial_tx_empty, |
454 | .set_mctrl = arc_serial_set_mctrl, |
455 | .get_mctrl = arc_serial_get_mctrl, |
456 | .stop_tx = arc_serial_stop_tx, |
457 | .start_tx = arc_serial_start_tx, |
458 | .stop_rx = arc_serial_stop_rx, |
459 | .break_ctl = arc_serial_break_ctl, |
460 | .startup = arc_serial_startup, |
461 | .shutdown = arc_serial_shutdown, |
462 | .set_termios = arc_serial_set_termios, |
463 | .type = arc_serial_type, |
464 | .release_port = arc_serial_release_port, |
465 | .request_port = arc_serial_request_port, |
466 | .config_port = arc_serial_config_port, |
467 | .verify_port = arc_serial_verify_port, |
468 | #ifdef CONFIG_CONSOLE_POLL |
469 | .poll_put_char = arc_serial_poll_putchar, |
470 | .poll_get_char = arc_serial_poll_getchar, |
471 | #endif |
472 | }; |
473 | |
474 | #ifdef CONFIG_SERIAL_ARC_CONSOLE |
475 | |
476 | static int arc_serial_console_setup(struct console *co, char *options) |
477 | { |
478 | struct uart_port *port; |
479 | int baud = 115200; |
480 | int bits = 8; |
481 | int parity = 'n'; |
482 | int flow = 'n'; |
483 | |
484 | if (co->index < 0 || co->index >= CONFIG_SERIAL_ARC_NR_PORTS) |
485 | return -ENODEV; |
486 | |
487 | /* |
488 | * The uart port backing the console (e.g. ttyARC1) might not have been |
489 | * init yet. If so, defer the console setup to after the port. |
490 | */ |
491 | port = &arc_uart_ports[co->index].port; |
492 | if (!port->membase) |
493 | return -ENODEV; |
494 | |
495 | if (options) |
496 | uart_parse_options(options, baud: &baud, parity: &parity, bits: &bits, flow: &flow); |
497 | |
498 | /* |
499 | * Serial core will call port->ops->set_termios( ) |
500 | * which will set the baud reg |
501 | */ |
502 | return uart_set_options(port, co, baud, parity, bits, flow); |
503 | } |
504 | |
505 | static void arc_serial_console_putchar(struct uart_port *port, unsigned char ch) |
506 | { |
507 | while (!(UART_GET_STATUS(port) & TXEMPTY)) |
508 | cpu_relax(); |
509 | |
510 | UART_SET_DATA(port, (unsigned char)ch); |
511 | } |
512 | |
513 | /* |
514 | * Interrupts are disabled on entering |
515 | */ |
516 | static void arc_serial_console_write(struct console *co, const char *s, |
517 | unsigned int count) |
518 | { |
519 | struct uart_port *port = &arc_uart_ports[co->index].port; |
520 | unsigned long flags; |
521 | |
522 | uart_port_lock_irqsave(up: port, flags: &flags); |
523 | uart_console_write(port, s, count, putchar: arc_serial_console_putchar); |
524 | uart_port_unlock_irqrestore(up: port, flags); |
525 | } |
526 | |
527 | static struct console arc_console = { |
528 | .name = ARC_SERIAL_DEV_NAME, |
529 | .write = arc_serial_console_write, |
530 | .device = uart_console_device, |
531 | .setup = arc_serial_console_setup, |
532 | .flags = CON_PRINTBUFFER, |
533 | .index = -1, |
534 | .data = &arc_uart_driver |
535 | }; |
536 | |
537 | static void arc_early_serial_write(struct console *con, const char *s, |
538 | unsigned int n) |
539 | { |
540 | struct earlycon_device *dev = con->data; |
541 | |
542 | uart_console_write(port: &dev->port, s, count: n, putchar: arc_serial_console_putchar); |
543 | } |
544 | |
545 | static int __init arc_early_console_setup(struct earlycon_device *dev, |
546 | const char *opt) |
547 | { |
548 | struct uart_port *port = &dev->port; |
549 | unsigned int l, h, hw_val; |
550 | |
551 | if (!dev->port.membase) |
552 | return -ENODEV; |
553 | |
554 | hw_val = port->uartclk / (dev->baud * 4) - 1; |
555 | l = hw_val & 0xFF; |
556 | h = (hw_val >> 8) & 0xFF; |
557 | |
558 | UART_SET_BAUDL(port, l); |
559 | UART_SET_BAUDH(port, h); |
560 | |
561 | dev->con->write = arc_early_serial_write; |
562 | return 0; |
563 | } |
564 | OF_EARLYCON_DECLARE(arc_uart, "snps,arc-uart", arc_early_console_setup); |
565 | |
566 | #endif /* CONFIG_SERIAL_ARC_CONSOLE */ |
567 | |
568 | static int arc_serial_probe(struct platform_device *pdev) |
569 | { |
570 | struct device_node *np = pdev->dev.of_node; |
571 | struct arc_uart_port *uart; |
572 | struct uart_port *port; |
573 | int dev_id; |
574 | u32 val; |
575 | |
576 | /* no device tree device */ |
577 | if (!np) |
578 | return -ENODEV; |
579 | |
580 | dev_id = of_alias_get_id(np, stem: "serial"); |
581 | if (dev_id < 0) |
582 | dev_id = 0; |
583 | |
584 | if (dev_id >= ARRAY_SIZE(arc_uart_ports)) { |
585 | dev_err(&pdev->dev, "serial%d out of range\n", dev_id); |
586 | return -EINVAL; |
587 | } |
588 | |
589 | uart = &arc_uart_ports[dev_id]; |
590 | port = &uart->port; |
591 | |
592 | if (of_property_read_u32(np, propname: "clock-frequency", out_value: &val)) { |
593 | dev_err(&pdev->dev, "clock-frequency property NOTset\n"); |
594 | return -EINVAL; |
595 | } |
596 | port->uartclk = val; |
597 | |
598 | if (of_property_read_u32(np, propname: "current-speed", out_value: &val)) { |
599 | dev_err(&pdev->dev, "current-speed property NOT set\n"); |
600 | return -EINVAL; |
601 | } |
602 | uart->baud = val; |
603 | |
604 | port->membase = devm_platform_ioremap_resource(pdev, index: 0); |
605 | if (IS_ERR(ptr: port->membase)) { |
606 | /* No point of dev_err since UART itself is hosed here */ |
607 | return PTR_ERR(ptr: port->membase); |
608 | } |
609 | |
610 | port->irq = irq_of_parse_and_map(node: np, index: 0); |
611 | |
612 | port->dev = &pdev->dev; |
613 | port->iotype = UPIO_MEM; |
614 | port->flags = UPF_BOOT_AUTOCONF; |
615 | port->line = dev_id; |
616 | port->ops = &arc_serial_pops; |
617 | port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_ARC_CONSOLE); |
618 | |
619 | port->fifosize = ARC_UART_TX_FIFO_SIZE; |
620 | |
621 | /* |
622 | * uart_insert_char( ) uses it in decideding whether to ignore a |
623 | * char or not. Explicitly setting it here, removes the subtelty |
624 | */ |
625 | port->ignore_status_mask = 0; |
626 | |
627 | return uart_add_one_port(reg: &arc_uart_driver, port: &arc_uart_ports[dev_id].port); |
628 | } |
629 | |
630 | static const struct of_device_id arc_uart_dt_ids[] = { |
631 | { .compatible = "snps,arc-uart"}, |
632 | { /* Sentinel */ } |
633 | }; |
634 | MODULE_DEVICE_TABLE(of, arc_uart_dt_ids); |
635 | |
636 | static struct platform_driver arc_platform_driver = { |
637 | .probe = arc_serial_probe, |
638 | .driver = { |
639 | .name = DRIVER_NAME, |
640 | .of_match_table = arc_uart_dt_ids, |
641 | }, |
642 | }; |
643 | |
644 | static int __init arc_serial_init(void) |
645 | { |
646 | int ret; |
647 | |
648 | ret = uart_register_driver(uart: &arc_uart_driver); |
649 | if (ret) |
650 | return ret; |
651 | |
652 | ret = platform_driver_register(&arc_platform_driver); |
653 | if (ret) |
654 | uart_unregister_driver(uart: &arc_uart_driver); |
655 | |
656 | return ret; |
657 | } |
658 | |
659 | static void __exit arc_serial_exit(void) |
660 | { |
661 | platform_driver_unregister(&arc_platform_driver); |
662 | uart_unregister_driver(uart: &arc_uart_driver); |
663 | } |
664 | |
665 | module_init(arc_serial_init); |
666 | module_exit(arc_serial_exit); |
667 | |
668 | MODULE_LICENSE("GPL"); |
669 | MODULE_ALIAS("platform:"DRIVER_NAME); |
670 | MODULE_AUTHOR("Vineet Gupta"); |
671 | MODULE_DESCRIPTION("ARC(Synopsys) On-Chip(fpga) serial driver"); |
672 |
Definitions
- arc_uart_port
- arc_uart_ports
- arc_console
- arc_uart_driver
- arc_serial_stop_rx
- arc_serial_stop_tx
- arc_serial_tx_empty
- arc_serial_tx_chars
- arc_serial_start_tx
- arc_serial_rx_chars
- arc_serial_isr
- arc_serial_get_mctrl
- arc_serial_set_mctrl
- arc_serial_break_ctl
- arc_serial_startup
- arc_serial_shutdown
- arc_serial_set_termios
- arc_serial_type
- arc_serial_release_port
- arc_serial_request_port
- arc_serial_verify_port
- arc_serial_config_port
- arc_serial_poll_putchar
- arc_serial_poll_getchar
- arc_serial_pops
- arc_serial_console_setup
- arc_serial_console_putchar
- arc_serial_console_write
- arc_console
- arc_early_serial_write
- arc_early_console_setup
- arc_serial_probe
- arc_uart_dt_ids
- arc_platform_driver
- arc_serial_init
Improve your Profiling and Debugging skills
Find out more