1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Microchip PIC32 SPI controller driver.
4 *
5 * Purna Chandra Mandal <purna.mandal@microchip.com>
6 * Copyright (c) 2016, Microchip Technology Inc.
7 */
8
9#include <linux/clk.h>
10#include <linux/clkdev.h>
11#include <linux/delay.h>
12#include <linux/dmaengine.h>
13#include <linux/dma-mapping.h>
14#include <linux/gpio/consumer.h>
15#include <linux/highmem.h>
16#include <linux/module.h>
17#include <linux/io.h>
18#include <linux/interrupt.h>
19#include <linux/of.h>
20#include <linux/of_irq.h>
21#include <linux/of_address.h>
22#include <linux/platform_device.h>
23#include <linux/spi/spi.h>
24
25/* SPI controller registers */
26struct pic32_spi_regs {
27 u32 ctrl;
28 u32 ctrl_clr;
29 u32 ctrl_set;
30 u32 ctrl_inv;
31 u32 status;
32 u32 status_clr;
33 u32 status_set;
34 u32 status_inv;
35 u32 buf;
36 u32 dontuse[3];
37 u32 baud;
38 u32 dontuse2[3];
39 u32 ctrl2;
40 u32 ctrl2_clr;
41 u32 ctrl2_set;
42 u32 ctrl2_inv;
43};
44
45/* Bit fields of SPI Control Register */
46#define CTRL_RX_INT_SHIFT 0 /* Rx interrupt generation */
47#define RX_FIFO_EMPTY 0
48#define RX_FIFO_NOT_EMPTY 1 /* not empty */
49#define RX_FIFO_HALF_FULL 2 /* full by half or more */
50#define RX_FIFO_FULL 3 /* completely full */
51
52#define CTRL_TX_INT_SHIFT 2 /* TX interrupt generation */
53#define TX_FIFO_ALL_EMPTY 0 /* completely empty */
54#define TX_FIFO_EMPTY 1 /* empty */
55#define TX_FIFO_HALF_EMPTY 2 /* empty by half or more */
56#define TX_FIFO_NOT_FULL 3 /* atleast one empty */
57
58#define CTRL_MSTEN BIT(5) /* enable master mode */
59#define CTRL_CKP BIT(6) /* active low */
60#define CTRL_CKE BIT(8) /* Tx on falling edge */
61#define CTRL_SMP BIT(9) /* Rx at middle or end of tx */
62#define CTRL_BPW_MASK 0x03 /* bits per word/sample */
63#define CTRL_BPW_SHIFT 10
64#define PIC32_BPW_8 0
65#define PIC32_BPW_16 1
66#define PIC32_BPW_32 2
67#define CTRL_SIDL BIT(13) /* sleep when idle */
68#define CTRL_ON BIT(15) /* enable macro */
69#define CTRL_ENHBUF BIT(16) /* enable enhanced buffering */
70#define CTRL_MCLKSEL BIT(23) /* select clock source */
71#define CTRL_MSSEN BIT(28) /* macro driven /SS */
72#define CTRL_FRMEN BIT(31) /* enable framing mode */
73
74/* Bit fields of SPI Status Register */
75#define STAT_RF_EMPTY BIT(5) /* RX Fifo empty */
76#define STAT_RX_OV BIT(6) /* err, s/w needs to clear */
77#define STAT_TX_UR BIT(8) /* UR in Framed SPI modes */
78#define STAT_FRM_ERR BIT(12) /* Multiple Frame Sync pulse */
79#define STAT_TF_LVL_MASK 0x1F
80#define STAT_TF_LVL_SHIFT 16
81#define STAT_RF_LVL_MASK 0x1F
82#define STAT_RF_LVL_SHIFT 24
83
84/* Bit fields of SPI Baud Register */
85#define BAUD_MASK 0x1ff
86
87/* Bit fields of SPI Control2 Register */
88#define CTRL2_TX_UR_EN BIT(10) /* Enable int on Tx under-run */
89#define CTRL2_RX_OV_EN BIT(11) /* Enable int on Rx over-run */
90#define CTRL2_FRM_ERR_EN BIT(12) /* Enable frame err int */
91
92/* Minimum DMA transfer size */
93#define PIC32_DMA_LEN_MIN 64
94
95struct pic32_spi {
96 dma_addr_t dma_base;
97 struct pic32_spi_regs __iomem *regs;
98 int fault_irq;
99 int rx_irq;
100 int tx_irq;
101 u32 fifo_n_byte; /* FIFO depth in bytes */
102 struct clk *clk;
103 struct spi_controller *host;
104 /* Current controller setting */
105 u32 speed_hz; /* spi-clk rate */
106 u32 mode;
107 u32 bits_per_word;
108 u32 fifo_n_elm; /* FIFO depth in words */
109#define PIC32F_DMA_PREP 0 /* DMA chnls configured */
110 unsigned long flags;
111 /* Current transfer state */
112 struct completion xfer_done;
113 /* PIO transfer specific */
114 const void *tx;
115 const void *tx_end;
116 const void *rx;
117 const void *rx_end;
118 int len;
119 void (*rx_fifo)(struct pic32_spi *);
120 void (*tx_fifo)(struct pic32_spi *);
121};
122
123static inline void pic32_spi_enable(struct pic32_spi *pic32s)
124{
125 writel(CTRL_ON | CTRL_SIDL, addr: &pic32s->regs->ctrl_set);
126}
127
128static inline void pic32_spi_disable(struct pic32_spi *pic32s)
129{
130 writel(CTRL_ON | CTRL_SIDL, addr: &pic32s->regs->ctrl_clr);
131
132 /* avoid SPI registers read/write at immediate next CPU clock */
133 ndelay(20);
134}
135
136static void pic32_spi_set_clk_rate(struct pic32_spi *pic32s, u32 spi_ck)
137{
138 u32 div;
139
140 /* div = (clk_in / 2 * spi_ck) - 1 */
141 div = DIV_ROUND_CLOSEST(clk_get_rate(pic32s->clk), 2 * spi_ck) - 1;
142
143 writel(val: div & BAUD_MASK, addr: &pic32s->regs->baud);
144}
145
146static inline u32 pic32_rx_fifo_level(struct pic32_spi *pic32s)
147{
148 u32 sr = readl(addr: &pic32s->regs->status);
149
150 return (sr >> STAT_RF_LVL_SHIFT) & STAT_RF_LVL_MASK;
151}
152
153static inline u32 pic32_tx_fifo_level(struct pic32_spi *pic32s)
154{
155 u32 sr = readl(addr: &pic32s->regs->status);
156
157 return (sr >> STAT_TF_LVL_SHIFT) & STAT_TF_LVL_MASK;
158}
159
160/* Return the max entries we can fill into tx fifo */
161static u32 pic32_tx_max(struct pic32_spi *pic32s, int n_bytes)
162{
163 u32 tx_left, tx_room, rxtx_gap;
164
165 tx_left = (pic32s->tx_end - pic32s->tx) / n_bytes;
166 tx_room = pic32s->fifo_n_elm - pic32_tx_fifo_level(pic32s);
167
168 /*
169 * Another concern is about the tx/rx mismatch, we
170 * though to use (pic32s->fifo_n_byte - rxfl - txfl) as
171 * one maximum value for tx, but it doesn't cover the
172 * data which is out of tx/rx fifo and inside the
173 * shift registers. So a ctrl from sw point of
174 * view is taken.
175 */
176 rxtx_gap = ((pic32s->rx_end - pic32s->rx) -
177 (pic32s->tx_end - pic32s->tx)) / n_bytes;
178 return min3(tx_left, tx_room, (u32)(pic32s->fifo_n_elm - rxtx_gap));
179}
180
181/* Return the max entries we should read out of rx fifo */
182static u32 pic32_rx_max(struct pic32_spi *pic32s, int n_bytes)
183{
184 u32 rx_left = (pic32s->rx_end - pic32s->rx) / n_bytes;
185
186 return min_t(u32, rx_left, pic32_rx_fifo_level(pic32s));
187}
188
189#define BUILD_SPI_FIFO_RW(__name, __type, __bwl) \
190static void pic32_spi_rx_##__name(struct pic32_spi *pic32s) \
191{ \
192 __type v; \
193 u32 mx = pic32_rx_max(pic32s, sizeof(__type)); \
194 for (; mx; mx--) { \
195 v = read##__bwl(&pic32s->regs->buf); \
196 if (pic32s->rx_end - pic32s->len) \
197 *(__type *)(pic32s->rx) = v; \
198 pic32s->rx += sizeof(__type); \
199 } \
200} \
201 \
202static void pic32_spi_tx_##__name(struct pic32_spi *pic32s) \
203{ \
204 __type v; \
205 u32 mx = pic32_tx_max(pic32s, sizeof(__type)); \
206 for (; mx ; mx--) { \
207 v = (__type)~0U; \
208 if (pic32s->tx_end - pic32s->len) \
209 v = *(__type *)(pic32s->tx); \
210 write##__bwl(v, &pic32s->regs->buf); \
211 pic32s->tx += sizeof(__type); \
212 } \
213}
214
215BUILD_SPI_FIFO_RW(byte, u8, b);
216BUILD_SPI_FIFO_RW(word, u16, w);
217BUILD_SPI_FIFO_RW(dword, u32, l);
218
219static void pic32_err_stop(struct pic32_spi *pic32s, const char *msg)
220{
221 /* disable all interrupts */
222 disable_irq_nosync(irq: pic32s->fault_irq);
223 disable_irq_nosync(irq: pic32s->rx_irq);
224 disable_irq_nosync(irq: pic32s->tx_irq);
225
226 /* Show err message and abort xfer with err */
227 dev_err(&pic32s->host->dev, "%s\n", msg);
228 if (pic32s->host->cur_msg)
229 pic32s->host->cur_msg->status = -EIO;
230 complete(&pic32s->xfer_done);
231}
232
233static irqreturn_t pic32_spi_fault_irq(int irq, void *dev_id)
234{
235 struct pic32_spi *pic32s = dev_id;
236 u32 status;
237
238 status = readl(addr: &pic32s->regs->status);
239
240 /* Error handling */
241 if (status & (STAT_RX_OV | STAT_TX_UR)) {
242 writel(STAT_RX_OV, addr: &pic32s->regs->status_clr);
243 writel(STAT_TX_UR, addr: &pic32s->regs->status_clr);
244 pic32_err_stop(pic32s, msg: "err_irq: fifo ov/ur-run\n");
245 return IRQ_HANDLED;
246 }
247
248 if (status & STAT_FRM_ERR) {
249 pic32_err_stop(pic32s, msg: "err_irq: frame error");
250 return IRQ_HANDLED;
251 }
252
253 if (!pic32s->host->cur_msg) {
254 pic32_err_stop(pic32s, msg: "err_irq: no mesg");
255 return IRQ_NONE;
256 }
257
258 return IRQ_NONE;
259}
260
261static irqreturn_t pic32_spi_rx_irq(int irq, void *dev_id)
262{
263 struct pic32_spi *pic32s = dev_id;
264
265 pic32s->rx_fifo(pic32s);
266
267 /* rx complete ? */
268 if (pic32s->rx_end == pic32s->rx) {
269 /* disable all interrupts */
270 disable_irq_nosync(irq: pic32s->fault_irq);
271 disable_irq_nosync(irq: pic32s->rx_irq);
272
273 /* complete current xfer */
274 complete(&pic32s->xfer_done);
275 }
276
277 return IRQ_HANDLED;
278}
279
280static irqreturn_t pic32_spi_tx_irq(int irq, void *dev_id)
281{
282 struct pic32_spi *pic32s = dev_id;
283
284 pic32s->tx_fifo(pic32s);
285
286 /* tx complete? disable tx interrupt */
287 if (pic32s->tx_end == pic32s->tx)
288 disable_irq_nosync(irq: pic32s->tx_irq);
289
290 return IRQ_HANDLED;
291}
292
293static void pic32_spi_dma_rx_notify(void *data)
294{
295 struct pic32_spi *pic32s = data;
296
297 complete(&pic32s->xfer_done);
298}
299
300static int pic32_spi_dma_transfer(struct pic32_spi *pic32s,
301 struct spi_transfer *xfer)
302{
303 struct spi_controller *host = pic32s->host;
304 struct dma_async_tx_descriptor *desc_rx;
305 struct dma_async_tx_descriptor *desc_tx;
306 dma_cookie_t cookie;
307 int ret;
308
309 if (!host->dma_rx || !host->dma_tx)
310 return -ENODEV;
311
312 desc_rx = dmaengine_prep_slave_sg(chan: host->dma_rx,
313 sgl: xfer->rx_sg.sgl,
314 sg_len: xfer->rx_sg.nents,
315 dir: DMA_DEV_TO_MEM,
316 flags: DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
317 if (!desc_rx) {
318 ret = -EINVAL;
319 goto err_dma;
320 }
321
322 desc_tx = dmaengine_prep_slave_sg(chan: host->dma_tx,
323 sgl: xfer->tx_sg.sgl,
324 sg_len: xfer->tx_sg.nents,
325 dir: DMA_MEM_TO_DEV,
326 flags: DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
327 if (!desc_tx) {
328 ret = -EINVAL;
329 goto err_dma;
330 }
331
332 /* Put callback on the RX transfer, that should finish last */
333 desc_rx->callback = pic32_spi_dma_rx_notify;
334 desc_rx->callback_param = pic32s;
335
336 cookie = dmaengine_submit(desc: desc_rx);
337 ret = dma_submit_error(cookie);
338 if (ret)
339 goto err_dma;
340
341 cookie = dmaengine_submit(desc: desc_tx);
342 ret = dma_submit_error(cookie);
343 if (ret)
344 goto err_dma_tx;
345
346 dma_async_issue_pending(chan: host->dma_rx);
347 dma_async_issue_pending(chan: host->dma_tx);
348
349 return 0;
350
351err_dma_tx:
352 dmaengine_terminate_all(chan: host->dma_rx);
353err_dma:
354 return ret;
355}
356
357static int pic32_spi_dma_config(struct pic32_spi *pic32s, u32 dma_width)
358{
359 int buf_offset = offsetof(struct pic32_spi_regs, buf);
360 struct spi_controller *host = pic32s->host;
361 struct dma_slave_config cfg;
362 int ret;
363
364 memset(&cfg, 0, sizeof(cfg));
365 cfg.device_fc = true;
366 cfg.src_addr = pic32s->dma_base + buf_offset;
367 cfg.dst_addr = pic32s->dma_base + buf_offset;
368 cfg.src_maxburst = pic32s->fifo_n_elm / 2; /* fill one-half */
369 cfg.dst_maxburst = pic32s->fifo_n_elm / 2; /* drain one-half */
370 cfg.src_addr_width = dma_width;
371 cfg.dst_addr_width = dma_width;
372 /* tx channel */
373 cfg.direction = DMA_MEM_TO_DEV;
374 ret = dmaengine_slave_config(chan: host->dma_tx, config: &cfg);
375 if (ret) {
376 dev_err(&host->dev, "tx channel setup failed\n");
377 return ret;
378 }
379 /* rx channel */
380 cfg.direction = DMA_DEV_TO_MEM;
381 ret = dmaengine_slave_config(chan: host->dma_rx, config: &cfg);
382 if (ret)
383 dev_err(&host->dev, "rx channel setup failed\n");
384
385 return ret;
386}
387
388static int pic32_spi_set_word_size(struct pic32_spi *pic32s, u8 bits_per_word)
389{
390 enum dma_slave_buswidth dmawidth;
391 u32 buswidth, v;
392
393 switch (bits_per_word) {
394 case 8:
395 pic32s->rx_fifo = pic32_spi_rx_byte;
396 pic32s->tx_fifo = pic32_spi_tx_byte;
397 buswidth = PIC32_BPW_8;
398 dmawidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
399 break;
400 case 16:
401 pic32s->rx_fifo = pic32_spi_rx_word;
402 pic32s->tx_fifo = pic32_spi_tx_word;
403 buswidth = PIC32_BPW_16;
404 dmawidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
405 break;
406 case 32:
407 pic32s->rx_fifo = pic32_spi_rx_dword;
408 pic32s->tx_fifo = pic32_spi_tx_dword;
409 buswidth = PIC32_BPW_32;
410 dmawidth = DMA_SLAVE_BUSWIDTH_4_BYTES;
411 break;
412 default:
413 /* not supported */
414 return -EINVAL;
415 }
416
417 /* calculate maximum number of words fifos can hold */
418 pic32s->fifo_n_elm = DIV_ROUND_UP(pic32s->fifo_n_byte,
419 bits_per_word / 8);
420 /* set word size */
421 v = readl(addr: &pic32s->regs->ctrl);
422 v &= ~(CTRL_BPW_MASK << CTRL_BPW_SHIFT);
423 v |= buswidth << CTRL_BPW_SHIFT;
424 writel(val: v, addr: &pic32s->regs->ctrl);
425
426 /* re-configure dma width, if required */
427 if (test_bit(PIC32F_DMA_PREP, &pic32s->flags))
428 pic32_spi_dma_config(pic32s, dma_width: dmawidth);
429
430 return 0;
431}
432
433static int pic32_spi_prepare_hardware(struct spi_controller *host)
434{
435 struct pic32_spi *pic32s = spi_controller_get_devdata(ctlr: host);
436
437 pic32_spi_enable(pic32s);
438
439 return 0;
440}
441
442static int pic32_spi_prepare_message(struct spi_controller *host,
443 struct spi_message *msg)
444{
445 struct pic32_spi *pic32s = spi_controller_get_devdata(ctlr: host);
446 struct spi_device *spi = msg->spi;
447 u32 val;
448
449 /* set device specific bits_per_word */
450 if (pic32s->bits_per_word != spi->bits_per_word) {
451 pic32_spi_set_word_size(pic32s, bits_per_word: spi->bits_per_word);
452 pic32s->bits_per_word = spi->bits_per_word;
453 }
454
455 /* device specific speed change */
456 if (pic32s->speed_hz != spi->max_speed_hz) {
457 pic32_spi_set_clk_rate(pic32s, spi_ck: spi->max_speed_hz);
458 pic32s->speed_hz = spi->max_speed_hz;
459 }
460
461 /* device specific mode change */
462 if (pic32s->mode != spi->mode) {
463 val = readl(addr: &pic32s->regs->ctrl);
464 /* active low */
465 if (spi->mode & SPI_CPOL)
466 val |= CTRL_CKP;
467 else
468 val &= ~CTRL_CKP;
469 /* tx on rising edge */
470 if (spi->mode & SPI_CPHA)
471 val &= ~CTRL_CKE;
472 else
473 val |= CTRL_CKE;
474
475 /* rx at end of tx */
476 val |= CTRL_SMP;
477 writel(val, addr: &pic32s->regs->ctrl);
478 pic32s->mode = spi->mode;
479 }
480
481 return 0;
482}
483
484static bool pic32_spi_can_dma(struct spi_controller *host,
485 struct spi_device *spi,
486 struct spi_transfer *xfer)
487{
488 struct pic32_spi *pic32s = spi_controller_get_devdata(ctlr: host);
489
490 /* skip using DMA on small size transfer to avoid overhead.*/
491 return (xfer->len >= PIC32_DMA_LEN_MIN) &&
492 test_bit(PIC32F_DMA_PREP, &pic32s->flags);
493}
494
495static int pic32_spi_one_transfer(struct spi_controller *host,
496 struct spi_device *spi,
497 struct spi_transfer *transfer)
498{
499 struct pic32_spi *pic32s;
500 bool dma_issued = false;
501 unsigned long timeout;
502 int ret;
503
504 pic32s = spi_controller_get_devdata(ctlr: host);
505
506 /* handle transfer specific word size change */
507 if (transfer->bits_per_word &&
508 (transfer->bits_per_word != pic32s->bits_per_word)) {
509 ret = pic32_spi_set_word_size(pic32s, bits_per_word: transfer->bits_per_word);
510 if (ret)
511 return ret;
512 pic32s->bits_per_word = transfer->bits_per_word;
513 }
514
515 /* handle transfer specific speed change */
516 if (transfer->speed_hz && (transfer->speed_hz != pic32s->speed_hz)) {
517 pic32_spi_set_clk_rate(pic32s, spi_ck: transfer->speed_hz);
518 pic32s->speed_hz = transfer->speed_hz;
519 }
520
521 reinit_completion(x: &pic32s->xfer_done);
522
523 /* transact by DMA mode */
524 if (transfer->rx_sg.nents && transfer->tx_sg.nents) {
525 ret = pic32_spi_dma_transfer(pic32s, xfer: transfer);
526 if (ret) {
527 dev_err(&spi->dev, "dma submit error\n");
528 return ret;
529 }
530
531 /* DMA issued */
532 dma_issued = true;
533 } else {
534 /* set current transfer information */
535 pic32s->tx = (const void *)transfer->tx_buf;
536 pic32s->rx = (const void *)transfer->rx_buf;
537 pic32s->tx_end = pic32s->tx + transfer->len;
538 pic32s->rx_end = pic32s->rx + transfer->len;
539 pic32s->len = transfer->len;
540
541 /* transact by interrupt driven PIO */
542 enable_irq(irq: pic32s->fault_irq);
543 enable_irq(irq: pic32s->rx_irq);
544 enable_irq(irq: pic32s->tx_irq);
545 }
546
547 /* wait for completion */
548 timeout = wait_for_completion_timeout(x: &pic32s->xfer_done, timeout: 2 * HZ);
549 if (timeout == 0) {
550 dev_err(&spi->dev, "wait error/timedout\n");
551 if (dma_issued) {
552 dmaengine_terminate_all(chan: host->dma_rx);
553 dmaengine_terminate_all(chan: host->dma_tx);
554 }
555 ret = -ETIMEDOUT;
556 } else {
557 ret = 0;
558 }
559
560 return ret;
561}
562
563static int pic32_spi_unprepare_message(struct spi_controller *host,
564 struct spi_message *msg)
565{
566 /* nothing to do */
567 return 0;
568}
569
570static int pic32_spi_unprepare_hardware(struct spi_controller *host)
571{
572 struct pic32_spi *pic32s = spi_controller_get_devdata(ctlr: host);
573
574 pic32_spi_disable(pic32s);
575
576 return 0;
577}
578
579/* This may be called multiple times by same spi dev */
580static int pic32_spi_setup(struct spi_device *spi)
581{
582 if (!spi->max_speed_hz) {
583 dev_err(&spi->dev, "No max speed HZ parameter\n");
584 return -EINVAL;
585 }
586
587 /* PIC32 spi controller can drive /CS during transfer depending
588 * on tx fifo fill-level. /CS will stay asserted as long as TX
589 * fifo is non-empty, else will be deasserted indicating
590 * completion of the ongoing transfer. This might result into
591 * unreliable/erroneous SPI transactions.
592 * To avoid that we will always handle /CS by toggling GPIO.
593 */
594 if (!spi_get_csgpiod(spi, idx: 0))
595 return -EINVAL;
596
597 return 0;
598}
599
600static void pic32_spi_cleanup(struct spi_device *spi)
601{
602 /* de-activate cs-gpio, gpiolib will handle inversion */
603 gpiod_direction_output(desc: spi_get_csgpiod(spi, idx: 0), value: 0);
604}
605
606static int pic32_spi_dma_prep(struct pic32_spi *pic32s, struct device *dev)
607{
608 struct spi_controller *host = pic32s->host;
609 int ret = 0;
610
611 host->dma_rx = dma_request_chan(dev, name: "spi-rx");
612 if (IS_ERR(ptr: host->dma_rx)) {
613 if (PTR_ERR(ptr: host->dma_rx) == -EPROBE_DEFER)
614 ret = -EPROBE_DEFER;
615 else
616 dev_warn(dev, "RX channel not found.\n");
617
618 host->dma_rx = NULL;
619 goto out_err;
620 }
621
622 host->dma_tx = dma_request_chan(dev, name: "spi-tx");
623 if (IS_ERR(ptr: host->dma_tx)) {
624 if (PTR_ERR(ptr: host->dma_tx) == -EPROBE_DEFER)
625 ret = -EPROBE_DEFER;
626 else
627 dev_warn(dev, "TX channel not found.\n");
628
629 host->dma_tx = NULL;
630 goto out_err;
631 }
632
633 if (pic32_spi_dma_config(pic32s, dma_width: DMA_SLAVE_BUSWIDTH_1_BYTE))
634 goto out_err;
635
636 /* DMA chnls allocated and prepared */
637 set_bit(PIC32F_DMA_PREP, addr: &pic32s->flags);
638
639 return 0;
640
641out_err:
642 if (host->dma_rx) {
643 dma_release_channel(chan: host->dma_rx);
644 host->dma_rx = NULL;
645 }
646
647 if (host->dma_tx) {
648 dma_release_channel(chan: host->dma_tx);
649 host->dma_tx = NULL;
650 }
651
652 return ret;
653}
654
655static void pic32_spi_dma_unprep(struct pic32_spi *pic32s)
656{
657 if (!test_bit(PIC32F_DMA_PREP, &pic32s->flags))
658 return;
659
660 clear_bit(PIC32F_DMA_PREP, addr: &pic32s->flags);
661 if (pic32s->host->dma_rx)
662 dma_release_channel(chan: pic32s->host->dma_rx);
663
664 if (pic32s->host->dma_tx)
665 dma_release_channel(chan: pic32s->host->dma_tx);
666}
667
668static void pic32_spi_hw_init(struct pic32_spi *pic32s)
669{
670 u32 ctrl;
671
672 /* disable hardware */
673 pic32_spi_disable(pic32s);
674
675 ctrl = readl(addr: &pic32s->regs->ctrl);
676 /* enable enhanced fifo of 128bit deep */
677 ctrl |= CTRL_ENHBUF;
678 pic32s->fifo_n_byte = 16;
679
680 /* disable framing mode */
681 ctrl &= ~CTRL_FRMEN;
682
683 /* enable host mode while disabled */
684 ctrl |= CTRL_MSTEN;
685
686 /* set tx fifo threshold interrupt */
687 ctrl &= ~(0x3 << CTRL_TX_INT_SHIFT);
688 ctrl |= (TX_FIFO_HALF_EMPTY << CTRL_TX_INT_SHIFT);
689
690 /* set rx fifo threshold interrupt */
691 ctrl &= ~(0x3 << CTRL_RX_INT_SHIFT);
692 ctrl |= (RX_FIFO_NOT_EMPTY << CTRL_RX_INT_SHIFT);
693
694 /* select clk source */
695 ctrl &= ~CTRL_MCLKSEL;
696
697 /* set manual /CS mode */
698 ctrl &= ~CTRL_MSSEN;
699
700 writel(val: ctrl, addr: &pic32s->regs->ctrl);
701
702 /* enable error reporting */
703 ctrl = CTRL2_TX_UR_EN | CTRL2_RX_OV_EN | CTRL2_FRM_ERR_EN;
704 writel(val: ctrl, addr: &pic32s->regs->ctrl2_set);
705}
706
707static int pic32_spi_hw_probe(struct platform_device *pdev,
708 struct pic32_spi *pic32s)
709{
710 struct resource *mem;
711 int ret;
712
713 pic32s->regs = devm_platform_get_and_ioremap_resource(pdev, index: 0, res: &mem);
714 if (IS_ERR(ptr: pic32s->regs))
715 return PTR_ERR(ptr: pic32s->regs);
716
717 pic32s->dma_base = mem->start;
718
719 /* get irq resources: err-irq, rx-irq, tx-irq */
720 pic32s->fault_irq = platform_get_irq_byname(pdev, "fault");
721 if (pic32s->fault_irq < 0)
722 return pic32s->fault_irq;
723
724 pic32s->rx_irq = platform_get_irq_byname(pdev, "rx");
725 if (pic32s->rx_irq < 0)
726 return pic32s->rx_irq;
727
728 pic32s->tx_irq = platform_get_irq_byname(pdev, "tx");
729 if (pic32s->tx_irq < 0)
730 return pic32s->tx_irq;
731
732 /* get clock */
733 pic32s->clk = devm_clk_get_enabled(dev: &pdev->dev, id: "mck0");
734 if (IS_ERR(ptr: pic32s->clk)) {
735 dev_err(&pdev->dev, "clk not found\n");
736 ret = PTR_ERR(ptr: pic32s->clk);
737 goto err_unmap_mem;
738 }
739
740 pic32_spi_hw_init(pic32s);
741
742 return 0;
743
744err_unmap_mem:
745 dev_err(&pdev->dev, "%s failed, err %d\n", __func__, ret);
746 return ret;
747}
748
749static int pic32_spi_probe(struct platform_device *pdev)
750{
751 struct spi_controller *host;
752 struct pic32_spi *pic32s;
753 int ret;
754
755 host = spi_alloc_host(dev: &pdev->dev, size: sizeof(*pic32s));
756 if (!host)
757 return -ENOMEM;
758
759 pic32s = spi_controller_get_devdata(ctlr: host);
760 pic32s->host = host;
761
762 ret = pic32_spi_hw_probe(pdev, pic32s);
763 if (ret)
764 goto err_host;
765
766 host->dev.of_node = pdev->dev.of_node;
767 host->mode_bits = SPI_MODE_3 | SPI_MODE_0 | SPI_CS_HIGH;
768 host->num_chipselect = 1; /* single chip-select */
769 host->max_speed_hz = clk_get_rate(clk: pic32s->clk);
770 host->setup = pic32_spi_setup;
771 host->cleanup = pic32_spi_cleanup;
772 host->flags = SPI_CONTROLLER_MUST_TX | SPI_CONTROLLER_MUST_RX;
773 host->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
774 SPI_BPW_MASK(32);
775 host->transfer_one = pic32_spi_one_transfer;
776 host->prepare_message = pic32_spi_prepare_message;
777 host->unprepare_message = pic32_spi_unprepare_message;
778 host->prepare_transfer_hardware = pic32_spi_prepare_hardware;
779 host->unprepare_transfer_hardware = pic32_spi_unprepare_hardware;
780 host->use_gpio_descriptors = true;
781
782 /* optional DMA support */
783 ret = pic32_spi_dma_prep(pic32s, dev: &pdev->dev);
784 if (ret)
785 goto err_bailout;
786
787 if (test_bit(PIC32F_DMA_PREP, &pic32s->flags))
788 host->can_dma = pic32_spi_can_dma;
789
790 init_completion(x: &pic32s->xfer_done);
791 pic32s->mode = -1;
792
793 /* install irq handlers (with irq-disabled) */
794 irq_set_status_flags(irq: pic32s->fault_irq, set: IRQ_NOAUTOEN);
795 ret = devm_request_irq(dev: &pdev->dev, irq: pic32s->fault_irq,
796 handler: pic32_spi_fault_irq, IRQF_NO_THREAD,
797 devname: dev_name(dev: &pdev->dev), dev_id: pic32s);
798 if (ret < 0) {
799 dev_err(&pdev->dev, "request fault-irq %d\n", pic32s->rx_irq);
800 goto err_bailout;
801 }
802
803 /* receive interrupt handler */
804 irq_set_status_flags(irq: pic32s->rx_irq, set: IRQ_NOAUTOEN);
805 ret = devm_request_irq(dev: &pdev->dev, irq: pic32s->rx_irq,
806 handler: pic32_spi_rx_irq, IRQF_NO_THREAD,
807 devname: dev_name(dev: &pdev->dev), dev_id: pic32s);
808 if (ret < 0) {
809 dev_err(&pdev->dev, "request rx-irq %d\n", pic32s->rx_irq);
810 goto err_bailout;
811 }
812
813 /* transmit interrupt handler */
814 irq_set_status_flags(irq: pic32s->tx_irq, set: IRQ_NOAUTOEN);
815 ret = devm_request_irq(dev: &pdev->dev, irq: pic32s->tx_irq,
816 handler: pic32_spi_tx_irq, IRQF_NO_THREAD,
817 devname: dev_name(dev: &pdev->dev), dev_id: pic32s);
818 if (ret < 0) {
819 dev_err(&pdev->dev, "request tx-irq %d\n", pic32s->tx_irq);
820 goto err_bailout;
821 }
822
823 /* register host */
824 ret = devm_spi_register_controller(dev: &pdev->dev, ctlr: host);
825 if (ret) {
826 dev_err(&host->dev, "failed registering spi host\n");
827 goto err_bailout;
828 }
829
830 platform_set_drvdata(pdev, data: pic32s);
831
832 return 0;
833
834err_bailout:
835 pic32_spi_dma_unprep(pic32s);
836err_host:
837 spi_controller_put(ctlr: host);
838 return ret;
839}
840
841static void pic32_spi_remove(struct platform_device *pdev)
842{
843 struct pic32_spi *pic32s;
844
845 pic32s = platform_get_drvdata(pdev);
846 pic32_spi_disable(pic32s);
847 pic32_spi_dma_unprep(pic32s);
848}
849
850static const struct of_device_id pic32_spi_of_match[] = {
851 {.compatible = "microchip,pic32mzda-spi",},
852 {},
853};
854MODULE_DEVICE_TABLE(of, pic32_spi_of_match);
855
856static struct platform_driver pic32_spi_driver = {
857 .driver = {
858 .name = "spi-pic32",
859 .of_match_table = of_match_ptr(pic32_spi_of_match),
860 },
861 .probe = pic32_spi_probe,
862 .remove_new = pic32_spi_remove,
863};
864
865module_platform_driver(pic32_spi_driver);
866
867MODULE_AUTHOR("Purna Chandra Mandal <purna.mandal@microchip.com>");
868MODULE_DESCRIPTION("Microchip SPI driver for PIC32 SPI controller.");
869MODULE_LICENSE("GPL v2");
870

source code of linux/drivers/spi/spi-pic32.c