1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright (C) 2009 Texas Instruments.
4 * Copyright (C) 2010 EF Johnson Technologies
5 */
6
7#include <linux/interrupt.h>
8#include <linux/io.h>
9#include <linux/gpio/consumer.h>
10#include <linux/module.h>
11#include <linux/delay.h>
12#include <linux/platform_device.h>
13#include <linux/err.h>
14#include <linux/clk.h>
15#include <linux/dmaengine.h>
16#include <linux/dma-mapping.h>
17#include <linux/of.h>
18#include <linux/spi/spi.h>
19#include <linux/spi/spi_bitbang.h>
20#include <linux/slab.h>
21
22#include <linux/platform_data/spi-davinci.h>
23
24#define CS_DEFAULT 0xFF
25
26#define SPIFMT_PHASE_MASK BIT(16)
27#define SPIFMT_POLARITY_MASK BIT(17)
28#define SPIFMT_DISTIMER_MASK BIT(18)
29#define SPIFMT_SHIFTDIR_MASK BIT(20)
30#define SPIFMT_WAITENA_MASK BIT(21)
31#define SPIFMT_PARITYENA_MASK BIT(22)
32#define SPIFMT_ODD_PARITY_MASK BIT(23)
33#define SPIFMT_WDELAY_MASK 0x3f000000u
34#define SPIFMT_WDELAY_SHIFT 24
35#define SPIFMT_PRESCALE_SHIFT 8
36
37/* SPIPC0 */
38#define SPIPC0_DIFUN_MASK BIT(11) /* MISO */
39#define SPIPC0_DOFUN_MASK BIT(10) /* MOSI */
40#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */
41#define SPIPC0_SPIENA_MASK BIT(8) /* nREADY */
42
43#define SPIINT_MASKALL 0x0101035F
44#define SPIINT_MASKINT 0x0000015F
45#define SPI_INTLVL_1 0x000001FF
46#define SPI_INTLVL_0 0x00000000
47
48/* SPIDAT1 (upper 16 bit defines) */
49#define SPIDAT1_CSHOLD_MASK BIT(12)
50#define SPIDAT1_WDEL BIT(10)
51
52/* SPIGCR1 */
53#define SPIGCR1_CLKMOD_MASK BIT(1)
54#define SPIGCR1_MASTER_MASK BIT(0)
55#define SPIGCR1_POWERDOWN_MASK BIT(8)
56#define SPIGCR1_LOOPBACK_MASK BIT(16)
57#define SPIGCR1_SPIENA_MASK BIT(24)
58
59/* SPIBUF */
60#define SPIBUF_TXFULL_MASK BIT(29)
61#define SPIBUF_RXEMPTY_MASK BIT(31)
62
63/* SPIDELAY */
64#define SPIDELAY_C2TDELAY_SHIFT 24
65#define SPIDELAY_C2TDELAY_MASK (0xFF << SPIDELAY_C2TDELAY_SHIFT)
66#define SPIDELAY_T2CDELAY_SHIFT 16
67#define SPIDELAY_T2CDELAY_MASK (0xFF << SPIDELAY_T2CDELAY_SHIFT)
68#define SPIDELAY_T2EDELAY_SHIFT 8
69#define SPIDELAY_T2EDELAY_MASK (0xFF << SPIDELAY_T2EDELAY_SHIFT)
70#define SPIDELAY_C2EDELAY_SHIFT 0
71#define SPIDELAY_C2EDELAY_MASK 0xFF
72
73/* Error Masks */
74#define SPIFLG_DLEN_ERR_MASK BIT(0)
75#define SPIFLG_TIMEOUT_MASK BIT(1)
76#define SPIFLG_PARERR_MASK BIT(2)
77#define SPIFLG_DESYNC_MASK BIT(3)
78#define SPIFLG_BITERR_MASK BIT(4)
79#define SPIFLG_OVRRUN_MASK BIT(6)
80#define SPIFLG_BUF_INIT_ACTIVE_MASK BIT(24)
81#define SPIFLG_ERROR_MASK (SPIFLG_DLEN_ERR_MASK \
82 | SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \
83 | SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \
84 | SPIFLG_OVRRUN_MASK)
85
86#define SPIINT_DMA_REQ_EN BIT(16)
87
88/* SPI Controller registers */
89#define SPIGCR0 0x00
90#define SPIGCR1 0x04
91#define SPIINT 0x08
92#define SPILVL 0x0c
93#define SPIFLG 0x10
94#define SPIPC0 0x14
95#define SPIDAT1 0x3c
96#define SPIBUF 0x40
97#define SPIDELAY 0x48
98#define SPIDEF 0x4c
99#define SPIFMT0 0x50
100
101#define DMA_MIN_BYTES 16
102
103/* SPI Controller driver's private data. */
104struct davinci_spi {
105 struct spi_bitbang bitbang;
106 struct clk *clk;
107
108 u8 version;
109 resource_size_t pbase;
110 void __iomem *base;
111 u32 irq;
112 struct completion done;
113
114 const void *tx;
115 void *rx;
116 int rcount;
117 int wcount;
118
119 struct dma_chan *dma_rx;
120 struct dma_chan *dma_tx;
121
122 struct davinci_spi_platform_data pdata;
123
124 void (*get_rx)(u32 rx_data, struct davinci_spi *);
125 u32 (*get_tx)(struct davinci_spi *);
126
127 u8 *bytes_per_word;
128
129 u8 prescaler_limit;
130};
131
132static struct davinci_spi_config davinci_spi_default_cfg;
133
134static void davinci_spi_rx_buf_u8(u32 data, struct davinci_spi *dspi)
135{
136 if (dspi->rx) {
137 u8 *rx = dspi->rx;
138 *rx++ = (u8)data;
139 dspi->rx = rx;
140 }
141}
142
143static void davinci_spi_rx_buf_u16(u32 data, struct davinci_spi *dspi)
144{
145 if (dspi->rx) {
146 u16 *rx = dspi->rx;
147 *rx++ = (u16)data;
148 dspi->rx = rx;
149 }
150}
151
152static u32 davinci_spi_tx_buf_u8(struct davinci_spi *dspi)
153{
154 u32 data = 0;
155
156 if (dspi->tx) {
157 const u8 *tx = dspi->tx;
158
159 data = *tx++;
160 dspi->tx = tx;
161 }
162 return data;
163}
164
165static u32 davinci_spi_tx_buf_u16(struct davinci_spi *dspi)
166{
167 u32 data = 0;
168
169 if (dspi->tx) {
170 const u16 *tx = dspi->tx;
171
172 data = *tx++;
173 dspi->tx = tx;
174 }
175 return data;
176}
177
178static inline void set_io_bits(void __iomem *addr, u32 bits)
179{
180 u32 v = ioread32(addr);
181
182 v |= bits;
183 iowrite32(v, addr);
184}
185
186static inline void clear_io_bits(void __iomem *addr, u32 bits)
187{
188 u32 v = ioread32(addr);
189
190 v &= ~bits;
191 iowrite32(v, addr);
192}
193
194/*
195 * Interface to control the chip select signal
196 */
197static void davinci_spi_chipselect(struct spi_device *spi, int value)
198{
199 struct davinci_spi *dspi;
200 struct davinci_spi_config *spicfg = spi->controller_data;
201 u8 chip_sel = spi_get_chipselect(spi, idx: 0);
202 u16 spidat1 = CS_DEFAULT;
203
204 dspi = spi_controller_get_devdata(ctlr: spi->controller);
205
206 /* program delay transfers if tx_delay is non zero */
207 if (spicfg && spicfg->wdelay)
208 spidat1 |= SPIDAT1_WDEL;
209
210 /*
211 * Board specific chip select logic decides the polarity and cs
212 * line for the controller
213 */
214 if (spi_get_csgpiod(spi, idx: 0)) {
215 if (value == BITBANG_CS_ACTIVE)
216 gpiod_set_value(desc: spi_get_csgpiod(spi, idx: 0), value: 1);
217 else
218 gpiod_set_value(desc: spi_get_csgpiod(spi, idx: 0), value: 0);
219 } else {
220 if (value == BITBANG_CS_ACTIVE) {
221 if (!(spi->mode & SPI_CS_WORD))
222 spidat1 |= SPIDAT1_CSHOLD_MASK;
223 spidat1 &= ~(0x1 << chip_sel);
224 }
225 }
226
227 iowrite16(spidat1, dspi->base + SPIDAT1 + 2);
228}
229
230/**
231 * davinci_spi_get_prescale - Calculates the correct prescale value
232 * @dspi: the controller data
233 * @max_speed_hz: the maximum rate the SPI clock can run at
234 *
235 * This function calculates the prescale value that generates a clock rate
236 * less than or equal to the specified maximum.
237 *
238 * Returns: calculated prescale value for easy programming into SPI registers
239 * or negative error number if valid prescalar cannot be updated.
240 */
241static inline int davinci_spi_get_prescale(struct davinci_spi *dspi,
242 u32 max_speed_hz)
243{
244 int ret;
245
246 /* Subtract 1 to match what will be programmed into SPI register. */
247 ret = DIV_ROUND_UP(clk_get_rate(dspi->clk), max_speed_hz) - 1;
248
249 if (ret < dspi->prescaler_limit || ret > 255)
250 return -EINVAL;
251
252 return ret;
253}
254
255/**
256 * davinci_spi_setup_transfer - This functions will determine transfer method
257 * @spi: spi device on which data transfer to be done
258 * @t: spi transfer in which transfer info is filled
259 *
260 * This function determines data transfer method (8/16/32 bit transfer).
261 * It will also set the SPI Clock Control register according to
262 * SPI slave device freq.
263 */
264static int davinci_spi_setup_transfer(struct spi_device *spi,
265 struct spi_transfer *t)
266{
267
268 struct davinci_spi *dspi;
269 struct davinci_spi_config *spicfg;
270 u8 bits_per_word = 0;
271 u32 hz = 0, spifmt = 0;
272 int prescale;
273
274 dspi = spi_controller_get_devdata(ctlr: spi->controller);
275 spicfg = spi->controller_data;
276 if (!spicfg)
277 spicfg = &davinci_spi_default_cfg;
278
279 if (t) {
280 bits_per_word = t->bits_per_word;
281 hz = t->speed_hz;
282 }
283
284 /* if bits_per_word is not set then set it default */
285 if (!bits_per_word)
286 bits_per_word = spi->bits_per_word;
287
288 /*
289 * Assign function pointer to appropriate transfer method
290 * 8bit, 16bit or 32bit transfer
291 */
292 if (bits_per_word <= 8) {
293 dspi->get_rx = davinci_spi_rx_buf_u8;
294 dspi->get_tx = davinci_spi_tx_buf_u8;
295 dspi->bytes_per_word[spi_get_chipselect(spi, idx: 0)] = 1;
296 } else {
297 dspi->get_rx = davinci_spi_rx_buf_u16;
298 dspi->get_tx = davinci_spi_tx_buf_u16;
299 dspi->bytes_per_word[spi_get_chipselect(spi, idx: 0)] = 2;
300 }
301
302 if (!hz)
303 hz = spi->max_speed_hz;
304
305 /* Set up SPIFMTn register, unique to this chipselect. */
306
307 prescale = davinci_spi_get_prescale(dspi, max_speed_hz: hz);
308 if (prescale < 0)
309 return prescale;
310
311 spifmt = (prescale << SPIFMT_PRESCALE_SHIFT) | (bits_per_word & 0x1f);
312
313 if (spi->mode & SPI_LSB_FIRST)
314 spifmt |= SPIFMT_SHIFTDIR_MASK;
315
316 if (spi->mode & SPI_CPOL)
317 spifmt |= SPIFMT_POLARITY_MASK;
318
319 if (!(spi->mode & SPI_CPHA))
320 spifmt |= SPIFMT_PHASE_MASK;
321
322 /*
323 * Assume wdelay is used only on SPI peripherals that has this field
324 * in SPIFMTn register and when it's configured from board file or DT.
325 */
326 if (spicfg->wdelay)
327 spifmt |= ((spicfg->wdelay << SPIFMT_WDELAY_SHIFT)
328 & SPIFMT_WDELAY_MASK);
329
330 /*
331 * Version 1 hardware supports two basic SPI modes:
332 * - Standard SPI mode uses 4 pins, with chipselect
333 * - 3 pin SPI is a 4 pin variant without CS (SPI_NO_CS)
334 * (distinct from SPI_3WIRE, with just one data wire;
335 * or similar variants without MOSI or without MISO)
336 *
337 * Version 2 hardware supports an optional handshaking signal,
338 * so it can support two more modes:
339 * - 5 pin SPI variant is standard SPI plus SPI_READY
340 * - 4 pin with enable is (SPI_READY | SPI_NO_CS)
341 */
342
343 if (dspi->version == SPI_VERSION_2) {
344
345 u32 delay = 0;
346
347 if (spicfg->odd_parity)
348 spifmt |= SPIFMT_ODD_PARITY_MASK;
349
350 if (spicfg->parity_enable)
351 spifmt |= SPIFMT_PARITYENA_MASK;
352
353 if (spicfg->timer_disable) {
354 spifmt |= SPIFMT_DISTIMER_MASK;
355 } else {
356 delay |= (spicfg->c2tdelay << SPIDELAY_C2TDELAY_SHIFT)
357 & SPIDELAY_C2TDELAY_MASK;
358 delay |= (spicfg->t2cdelay << SPIDELAY_T2CDELAY_SHIFT)
359 & SPIDELAY_T2CDELAY_MASK;
360 }
361
362 if (spi->mode & SPI_READY) {
363 spifmt |= SPIFMT_WAITENA_MASK;
364 delay |= (spicfg->t2edelay << SPIDELAY_T2EDELAY_SHIFT)
365 & SPIDELAY_T2EDELAY_MASK;
366 delay |= (spicfg->c2edelay << SPIDELAY_C2EDELAY_SHIFT)
367 & SPIDELAY_C2EDELAY_MASK;
368 }
369
370 iowrite32(delay, dspi->base + SPIDELAY);
371 }
372
373 iowrite32(spifmt, dspi->base + SPIFMT0);
374
375 return 0;
376}
377
378static int davinci_spi_of_setup(struct spi_device *spi)
379{
380 struct davinci_spi_config *spicfg = spi->controller_data;
381 struct device_node *np = spi->dev.of_node;
382 struct davinci_spi *dspi = spi_controller_get_devdata(ctlr: spi->controller);
383 u32 prop;
384
385 if (spicfg == NULL && np) {
386 spicfg = kzalloc(size: sizeof(*spicfg), GFP_KERNEL);
387 if (!spicfg)
388 return -ENOMEM;
389 *spicfg = davinci_spi_default_cfg;
390 /* override with dt configured values */
391 if (!of_property_read_u32(np, propname: "ti,spi-wdelay", out_value: &prop))
392 spicfg->wdelay = (u8)prop;
393 spi->controller_data = spicfg;
394
395 if (dspi->dma_rx && dspi->dma_tx)
396 spicfg->io_type = SPI_IO_TYPE_DMA;
397 }
398
399 return 0;
400}
401
402/**
403 * davinci_spi_setup - This functions will set default transfer method
404 * @spi: spi device on which data transfer to be done
405 *
406 * This functions sets the default transfer method.
407 */
408static int davinci_spi_setup(struct spi_device *spi)
409{
410 struct davinci_spi *dspi;
411 struct device_node *np = spi->dev.of_node;
412 bool internal_cs = true;
413
414 dspi = spi_controller_get_devdata(ctlr: spi->controller);
415
416 if (!(spi->mode & SPI_NO_CS)) {
417 if (np && spi_get_csgpiod(spi, idx: 0))
418 internal_cs = false;
419
420 if (internal_cs)
421 set_io_bits(addr: dspi->base + SPIPC0, bits: 1 << spi_get_chipselect(spi, idx: 0));
422 }
423
424 if (spi->mode & SPI_READY)
425 set_io_bits(addr: dspi->base + SPIPC0, SPIPC0_SPIENA_MASK);
426
427 if (spi->mode & SPI_LOOP)
428 set_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_LOOPBACK_MASK);
429 else
430 clear_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_LOOPBACK_MASK);
431
432 return davinci_spi_of_setup(spi);
433}
434
435static void davinci_spi_cleanup(struct spi_device *spi)
436{
437 struct davinci_spi_config *spicfg = spi->controller_data;
438
439 spi->controller_data = NULL;
440 if (spi->dev.of_node)
441 kfree(objp: spicfg);
442}
443
444static bool davinci_spi_can_dma(struct spi_controller *host,
445 struct spi_device *spi,
446 struct spi_transfer *xfer)
447{
448 struct davinci_spi_config *spicfg = spi->controller_data;
449 bool can_dma = false;
450
451 if (spicfg)
452 can_dma = (spicfg->io_type == SPI_IO_TYPE_DMA) &&
453 (xfer->len >= DMA_MIN_BYTES) &&
454 !is_vmalloc_addr(x: xfer->rx_buf) &&
455 !is_vmalloc_addr(x: xfer->tx_buf);
456
457 return can_dma;
458}
459
460static int davinci_spi_check_error(struct davinci_spi *dspi, int int_status)
461{
462 struct device *sdev = dspi->bitbang.ctlr->dev.parent;
463
464 if (int_status & SPIFLG_TIMEOUT_MASK) {
465 dev_err(sdev, "SPI Time-out Error\n");
466 return -ETIMEDOUT;
467 }
468 if (int_status & SPIFLG_DESYNC_MASK) {
469 dev_err(sdev, "SPI Desynchronization Error\n");
470 return -EIO;
471 }
472 if (int_status & SPIFLG_BITERR_MASK) {
473 dev_err(sdev, "SPI Bit error\n");
474 return -EIO;
475 }
476
477 if (dspi->version == SPI_VERSION_2) {
478 if (int_status & SPIFLG_DLEN_ERR_MASK) {
479 dev_err(sdev, "SPI Data Length Error\n");
480 return -EIO;
481 }
482 if (int_status & SPIFLG_PARERR_MASK) {
483 dev_err(sdev, "SPI Parity Error\n");
484 return -EIO;
485 }
486 if (int_status & SPIFLG_OVRRUN_MASK) {
487 dev_err(sdev, "SPI Data Overrun error\n");
488 return -EIO;
489 }
490 if (int_status & SPIFLG_BUF_INIT_ACTIVE_MASK) {
491 dev_err(sdev, "SPI Buffer Init Active\n");
492 return -EBUSY;
493 }
494 }
495
496 return 0;
497}
498
499/**
500 * davinci_spi_process_events - check for and handle any SPI controller events
501 * @dspi: the controller data
502 *
503 * This function will check the SPIFLG register and handle any events that are
504 * detected there
505 */
506static int davinci_spi_process_events(struct davinci_spi *dspi)
507{
508 u32 buf, status, errors = 0, spidat1;
509
510 buf = ioread32(dspi->base + SPIBUF);
511
512 if (dspi->rcount > 0 && !(buf & SPIBUF_RXEMPTY_MASK)) {
513 dspi->get_rx(buf & 0xFFFF, dspi);
514 dspi->rcount--;
515 }
516
517 status = ioread32(dspi->base + SPIFLG);
518
519 if (unlikely(status & SPIFLG_ERROR_MASK)) {
520 errors = status & SPIFLG_ERROR_MASK;
521 goto out;
522 }
523
524 if (dspi->wcount > 0 && !(buf & SPIBUF_TXFULL_MASK)) {
525 spidat1 = ioread32(dspi->base + SPIDAT1);
526 dspi->wcount--;
527 spidat1 &= ~0xFFFF;
528 spidat1 |= 0xFFFF & dspi->get_tx(dspi);
529 iowrite32(spidat1, dspi->base + SPIDAT1);
530 }
531
532out:
533 return errors;
534}
535
536static void davinci_spi_dma_rx_callback(void *data)
537{
538 struct davinci_spi *dspi = (struct davinci_spi *)data;
539
540 dspi->rcount = 0;
541
542 if (!dspi->wcount && !dspi->rcount)
543 complete(&dspi->done);
544}
545
546static void davinci_spi_dma_tx_callback(void *data)
547{
548 struct davinci_spi *dspi = (struct davinci_spi *)data;
549
550 dspi->wcount = 0;
551
552 if (!dspi->wcount && !dspi->rcount)
553 complete(&dspi->done);
554}
555
556/**
557 * davinci_spi_bufs - functions which will handle transfer data
558 * @spi: spi device on which data transfer to be done
559 * @t: spi transfer in which transfer info is filled
560 *
561 * This function will put data to be transferred into data register
562 * of SPI controller and then wait until the completion will be marked
563 * by the IRQ Handler.
564 */
565static int davinci_spi_bufs(struct spi_device *spi, struct spi_transfer *t)
566{
567 struct davinci_spi *dspi;
568 int data_type, ret = -ENOMEM;
569 u32 tx_data, spidat1;
570 u32 errors = 0;
571 struct davinci_spi_config *spicfg;
572 struct davinci_spi_platform_data *pdata;
573
574 dspi = spi_controller_get_devdata(ctlr: spi->controller);
575 pdata = &dspi->pdata;
576 spicfg = (struct davinci_spi_config *)spi->controller_data;
577 if (!spicfg)
578 spicfg = &davinci_spi_default_cfg;
579
580 /* convert len to words based on bits_per_word */
581 data_type = dspi->bytes_per_word[spi_get_chipselect(spi, idx: 0)];
582
583 dspi->tx = t->tx_buf;
584 dspi->rx = t->rx_buf;
585 dspi->wcount = t->len / data_type;
586 dspi->rcount = dspi->wcount;
587
588 spidat1 = ioread32(dspi->base + SPIDAT1);
589
590 clear_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK);
591 set_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_SPIENA_MASK);
592
593 reinit_completion(x: &dspi->done);
594
595 if (!davinci_spi_can_dma(host: spi->controller, spi, xfer: t)) {
596 if (spicfg->io_type != SPI_IO_TYPE_POLL)
597 set_io_bits(addr: dspi->base + SPIINT, SPIINT_MASKINT);
598 /* start the transfer */
599 dspi->wcount--;
600 tx_data = dspi->get_tx(dspi);
601 spidat1 &= 0xFFFF0000;
602 spidat1 |= tx_data & 0xFFFF;
603 iowrite32(spidat1, dspi->base + SPIDAT1);
604 } else {
605 struct dma_slave_config dma_rx_conf = {
606 .direction = DMA_DEV_TO_MEM,
607 .src_addr = (unsigned long)dspi->pbase + SPIBUF,
608 .src_addr_width = data_type,
609 .src_maxburst = 1,
610 };
611 struct dma_slave_config dma_tx_conf = {
612 .direction = DMA_MEM_TO_DEV,
613 .dst_addr = (unsigned long)dspi->pbase + SPIDAT1,
614 .dst_addr_width = data_type,
615 .dst_maxburst = 1,
616 };
617 struct dma_async_tx_descriptor *rxdesc;
618 struct dma_async_tx_descriptor *txdesc;
619
620 dmaengine_slave_config(chan: dspi->dma_rx, config: &dma_rx_conf);
621 dmaengine_slave_config(chan: dspi->dma_tx, config: &dma_tx_conf);
622
623 rxdesc = dmaengine_prep_slave_sg(chan: dspi->dma_rx,
624 sgl: t->rx_sg.sgl, sg_len: t->rx_sg.nents, dir: DMA_DEV_TO_MEM,
625 flags: DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
626 if (!rxdesc)
627 goto err_desc;
628
629 if (!t->tx_buf) {
630 /* To avoid errors when doing rx-only transfers with
631 * many SG entries (> 20), use the rx buffer as the
632 * dummy tx buffer so that dma reloads are done at the
633 * same time for rx and tx.
634 */
635 t->tx_sg.sgl = t->rx_sg.sgl;
636 t->tx_sg.nents = t->rx_sg.nents;
637 }
638
639 txdesc = dmaengine_prep_slave_sg(chan: dspi->dma_tx,
640 sgl: t->tx_sg.sgl, sg_len: t->tx_sg.nents, dir: DMA_MEM_TO_DEV,
641 flags: DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
642 if (!txdesc)
643 goto err_desc;
644
645 rxdesc->callback = davinci_spi_dma_rx_callback;
646 rxdesc->callback_param = (void *)dspi;
647 txdesc->callback = davinci_spi_dma_tx_callback;
648 txdesc->callback_param = (void *)dspi;
649
650 if (pdata->cshold_bug)
651 iowrite16(spidat1 >> 16, dspi->base + SPIDAT1 + 2);
652
653 dmaengine_submit(desc: rxdesc);
654 dmaengine_submit(desc: txdesc);
655
656 dma_async_issue_pending(chan: dspi->dma_rx);
657 dma_async_issue_pending(chan: dspi->dma_tx);
658
659 set_io_bits(addr: dspi->base + SPIINT, SPIINT_DMA_REQ_EN);
660 }
661
662 /* Wait for the transfer to complete */
663 if (spicfg->io_type != SPI_IO_TYPE_POLL) {
664 if (wait_for_completion_timeout(x: &dspi->done, HZ) == 0)
665 errors = SPIFLG_TIMEOUT_MASK;
666 } else {
667 while (dspi->rcount > 0 || dspi->wcount > 0) {
668 errors = davinci_spi_process_events(dspi);
669 if (errors)
670 break;
671 cpu_relax();
672 }
673 }
674
675 clear_io_bits(addr: dspi->base + SPIINT, SPIINT_MASKALL);
676 if (davinci_spi_can_dma(host: spi->controller, spi, xfer: t))
677 clear_io_bits(addr: dspi->base + SPIINT, SPIINT_DMA_REQ_EN);
678
679 clear_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_SPIENA_MASK);
680 set_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK);
681
682 /*
683 * Check for bit error, desync error,parity error,timeout error and
684 * receive overflow errors
685 */
686 if (errors) {
687 ret = davinci_spi_check_error(dspi, int_status: errors);
688 WARN(!ret, "%s: error reported but no error found!\n",
689 dev_name(&spi->dev));
690 return ret;
691 }
692
693 if (dspi->rcount != 0 || dspi->wcount != 0) {
694 dev_err(&spi->dev, "SPI data transfer error\n");
695 return -EIO;
696 }
697
698 return t->len;
699
700err_desc:
701 return ret;
702}
703
704/**
705 * dummy_thread_fn - dummy thread function
706 * @irq: IRQ number for this SPI Master
707 * @data: structure for SPI Master controller davinci_spi
708 *
709 * This is to satisfy the request_threaded_irq() API so that the irq
710 * handler is called in interrupt context.
711 */
712static irqreturn_t dummy_thread_fn(s32 irq, void *data)
713{
714 return IRQ_HANDLED;
715}
716
717/**
718 * davinci_spi_irq - Interrupt handler for SPI Master Controller
719 * @irq: IRQ number for this SPI Master
720 * @data: structure for SPI Master controller davinci_spi
721 *
722 * ISR will determine that interrupt arrives either for READ or WRITE command.
723 * According to command it will do the appropriate action. It will check
724 * transfer length and if it is not zero then dispatch transfer command again.
725 * If transfer length is zero then it will indicate the COMPLETION so that
726 * davinci_spi_bufs function can go ahead.
727 */
728static irqreturn_t davinci_spi_irq(s32 irq, void *data)
729{
730 struct davinci_spi *dspi = data;
731 int status;
732
733 status = davinci_spi_process_events(dspi);
734 if (unlikely(status != 0))
735 clear_io_bits(addr: dspi->base + SPIINT, SPIINT_MASKINT);
736
737 if ((!dspi->rcount && !dspi->wcount) || status)
738 complete(&dspi->done);
739
740 return IRQ_HANDLED;
741}
742
743static int davinci_spi_request_dma(struct davinci_spi *dspi)
744{
745 struct device *sdev = dspi->bitbang.ctlr->dev.parent;
746
747 dspi->dma_rx = dma_request_chan(dev: sdev, name: "rx");
748 if (IS_ERR(ptr: dspi->dma_rx))
749 return PTR_ERR(ptr: dspi->dma_rx);
750
751 dspi->dma_tx = dma_request_chan(dev: sdev, name: "tx");
752 if (IS_ERR(ptr: dspi->dma_tx)) {
753 dma_release_channel(chan: dspi->dma_rx);
754 return PTR_ERR(ptr: dspi->dma_tx);
755 }
756
757 return 0;
758}
759
760#if defined(CONFIG_OF)
761
762/* OF SPI data structure */
763struct davinci_spi_of_data {
764 u8 version;
765 u8 prescaler_limit;
766};
767
768static const struct davinci_spi_of_data dm6441_spi_data = {
769 .version = SPI_VERSION_1,
770 .prescaler_limit = 2,
771};
772
773static const struct davinci_spi_of_data da830_spi_data = {
774 .version = SPI_VERSION_2,
775 .prescaler_limit = 2,
776};
777
778static const struct davinci_spi_of_data keystone_spi_data = {
779 .version = SPI_VERSION_1,
780 .prescaler_limit = 0,
781};
782
783static const struct of_device_id davinci_spi_of_match[] = {
784 {
785 .compatible = "ti,dm6441-spi",
786 .data = &dm6441_spi_data,
787 },
788 {
789 .compatible = "ti,da830-spi",
790 .data = &da830_spi_data,
791 },
792 {
793 .compatible = "ti,keystone-spi",
794 .data = &keystone_spi_data,
795 },
796 { },
797};
798MODULE_DEVICE_TABLE(of, davinci_spi_of_match);
799
800/**
801 * spi_davinci_get_pdata - Get platform data from DTS binding
802 * @pdev: ptr to platform data
803 * @dspi: ptr to driver data
804 *
805 * Parses and populates pdata in dspi from device tree bindings.
806 *
807 * NOTE: Not all platform data params are supported currently.
808 */
809static int spi_davinci_get_pdata(struct platform_device *pdev,
810 struct davinci_spi *dspi)
811{
812 struct device_node *node = pdev->dev.of_node;
813 const struct davinci_spi_of_data *spi_data;
814 struct davinci_spi_platform_data *pdata;
815 unsigned int num_cs, intr_line = 0;
816
817 pdata = &dspi->pdata;
818
819 spi_data = device_get_match_data(dev: &pdev->dev);
820
821 pdata->version = spi_data->version;
822 pdata->prescaler_limit = spi_data->prescaler_limit;
823 /*
824 * default num_cs is 1 and all chipsel are internal to the chip
825 * indicated by chip_sel being NULL or cs_gpios being NULL or
826 * set to -ENOENT. num-cs includes internal as well as gpios.
827 * indicated by chip_sel being NULL. GPIO based CS is not
828 * supported yet in DT bindings.
829 */
830 num_cs = 1;
831 of_property_read_u32(np: node, propname: "num-cs", out_value: &num_cs);
832 pdata->num_chipselect = num_cs;
833 of_property_read_u32(np: node, propname: "ti,davinci-spi-intr-line", out_value: &intr_line);
834 pdata->intr_line = intr_line;
835 return 0;
836}
837#else
838static int spi_davinci_get_pdata(struct platform_device *pdev,
839 struct davinci_spi *dspi)
840{
841 return -ENODEV;
842}
843#endif
844
845/**
846 * davinci_spi_probe - probe function for SPI Master Controller
847 * @pdev: platform_device structure which contains plateform specific data
848 *
849 * According to Linux Device Model this function will be invoked by Linux
850 * with platform_device struct which contains the device specific info.
851 * This function will map the SPI controller's memory, register IRQ,
852 * Reset SPI controller and setting its registers to default value.
853 * It will invoke spi_bitbang_start to create work queue so that client driver
854 * can register transfer method to work queue.
855 */
856static int davinci_spi_probe(struct platform_device *pdev)
857{
858 struct spi_controller *host;
859 struct davinci_spi *dspi;
860 struct davinci_spi_platform_data *pdata;
861 struct resource *r;
862 int ret = 0;
863 u32 spipc0;
864
865 host = spi_alloc_host(dev: &pdev->dev, size: sizeof(struct davinci_spi));
866 if (host == NULL) {
867 ret = -ENOMEM;
868 goto err;
869 }
870
871 platform_set_drvdata(pdev, data: host);
872
873 dspi = spi_controller_get_devdata(ctlr: host);
874
875 if (dev_get_platdata(dev: &pdev->dev)) {
876 pdata = dev_get_platdata(dev: &pdev->dev);
877 dspi->pdata = *pdata;
878 } else {
879 /* update dspi pdata with that from the DT */
880 ret = spi_davinci_get_pdata(pdev, dspi);
881 if (ret < 0)
882 goto free_host;
883 }
884
885 /* pdata in dspi is now updated and point pdata to that */
886 pdata = &dspi->pdata;
887
888 dspi->bytes_per_word = devm_kcalloc(dev: &pdev->dev,
889 n: pdata->num_chipselect,
890 size: sizeof(*dspi->bytes_per_word),
891 GFP_KERNEL);
892 if (dspi->bytes_per_word == NULL) {
893 ret = -ENOMEM;
894 goto free_host;
895 }
896
897 dspi->base = devm_platform_get_and_ioremap_resource(pdev, index: 0, res: &r);
898 if (IS_ERR(ptr: dspi->base)) {
899 ret = PTR_ERR(ptr: dspi->base);
900 goto free_host;
901 }
902 dspi->pbase = r->start;
903
904 init_completion(x: &dspi->done);
905
906 ret = platform_get_irq(pdev, 0);
907 if (ret < 0)
908 goto free_host;
909 dspi->irq = ret;
910
911 ret = devm_request_threaded_irq(dev: &pdev->dev, irq: dspi->irq, handler: davinci_spi_irq,
912 thread_fn: dummy_thread_fn, irqflags: 0, devname: dev_name(dev: &pdev->dev), dev_id: dspi);
913 if (ret)
914 goto free_host;
915
916 dspi->bitbang.ctlr = host;
917
918 dspi->clk = devm_clk_get_enabled(dev: &pdev->dev, NULL);
919 if (IS_ERR(ptr: dspi->clk)) {
920 ret = -ENODEV;
921 goto free_host;
922 }
923
924 host->use_gpio_descriptors = true;
925 host->dev.of_node = pdev->dev.of_node;
926 host->bus_num = pdev->id;
927 host->num_chipselect = pdata->num_chipselect;
928 host->bits_per_word_mask = SPI_BPW_RANGE_MASK(2, 16);
929 host->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_GPIO_SS;
930 host->setup = davinci_spi_setup;
931 host->cleanup = davinci_spi_cleanup;
932 host->can_dma = davinci_spi_can_dma;
933
934 dspi->bitbang.chipselect = davinci_spi_chipselect;
935 dspi->bitbang.setup_transfer = davinci_spi_setup_transfer;
936 dspi->prescaler_limit = pdata->prescaler_limit;
937 dspi->version = pdata->version;
938
939 dspi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP | SPI_CS_WORD;
940 if (dspi->version == SPI_VERSION_2)
941 dspi->bitbang.flags |= SPI_READY;
942
943 dspi->bitbang.txrx_bufs = davinci_spi_bufs;
944
945 ret = davinci_spi_request_dma(dspi);
946 if (ret == -EPROBE_DEFER) {
947 goto free_host;
948 } else if (ret) {
949 dev_info(&pdev->dev, "DMA is not supported (%d)\n", ret);
950 dspi->dma_rx = NULL;
951 dspi->dma_tx = NULL;
952 }
953
954 dspi->get_rx = davinci_spi_rx_buf_u8;
955 dspi->get_tx = davinci_spi_tx_buf_u8;
956
957 /* Reset In/OUT SPI module */
958 iowrite32(0, dspi->base + SPIGCR0);
959 udelay(100);
960 iowrite32(1, dspi->base + SPIGCR0);
961
962 /* Set up SPIPC0. CS and ENA init is done in davinci_spi_setup */
963 spipc0 = SPIPC0_DIFUN_MASK | SPIPC0_DOFUN_MASK | SPIPC0_CLKFUN_MASK;
964 iowrite32(spipc0, dspi->base + SPIPC0);
965
966 if (pdata->intr_line)
967 iowrite32(SPI_INTLVL_1, dspi->base + SPILVL);
968 else
969 iowrite32(SPI_INTLVL_0, dspi->base + SPILVL);
970
971 iowrite32(CS_DEFAULT, dspi->base + SPIDEF);
972
973 /* host mode default */
974 set_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_CLKMOD_MASK);
975 set_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_MASTER_MASK);
976 set_io_bits(addr: dspi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK);
977
978 ret = spi_bitbang_start(spi: &dspi->bitbang);
979 if (ret)
980 goto free_dma;
981
982 dev_info(&pdev->dev, "Controller at 0x%p\n", dspi->base);
983
984 return ret;
985
986free_dma:
987 if (dspi->dma_rx) {
988 dma_release_channel(chan: dspi->dma_rx);
989 dma_release_channel(chan: dspi->dma_tx);
990 }
991free_host:
992 spi_controller_put(ctlr: host);
993err:
994 return ret;
995}
996
997/**
998 * davinci_spi_remove - remove function for SPI Master Controller
999 * @pdev: platform_device structure which contains plateform specific data
1000 *
1001 * This function will do the reverse action of davinci_spi_probe function
1002 * It will free the IRQ and SPI controller's memory region.
1003 * It will also call spi_bitbang_stop to destroy the work queue which was
1004 * created by spi_bitbang_start.
1005 */
1006static void davinci_spi_remove(struct platform_device *pdev)
1007{
1008 struct davinci_spi *dspi;
1009 struct spi_controller *host;
1010
1011 host = platform_get_drvdata(pdev);
1012 dspi = spi_controller_get_devdata(ctlr: host);
1013
1014 spi_bitbang_stop(spi: &dspi->bitbang);
1015
1016 if (dspi->dma_rx) {
1017 dma_release_channel(chan: dspi->dma_rx);
1018 dma_release_channel(chan: dspi->dma_tx);
1019 }
1020
1021 spi_controller_put(ctlr: host);
1022}
1023
1024static struct platform_driver davinci_spi_driver = {
1025 .driver = {
1026 .name = "spi_davinci",
1027 .of_match_table = of_match_ptr(davinci_spi_of_match),
1028 },
1029 .probe = davinci_spi_probe,
1030 .remove_new = davinci_spi_remove,
1031};
1032module_platform_driver(davinci_spi_driver);
1033
1034MODULE_DESCRIPTION("TI DaVinci SPI Master Controller Driver");
1035MODULE_LICENSE("GPL");
1036

source code of linux/drivers/spi/spi-davinci.c